Eiki Projector Lc Sxg400 Specifications

							51
This function prevents an unauthorized person from 
changing the screen logo.
 Off  ...........  The screen logo can be changed freely from 
the Logo Menu (p.54).
  On  ............  The screen logo cannot be changed without 
a Logo PIN code.
If you want to change the Logo PIN code lock setting, 
press the SELECT button and the Logo PIN code dialog 
box appears. Enter a Logo PIN code by following the 
steps below. The initial Logo PIN code is set to “4321” at 
the factory.
Logo PIN code lock
Enter a Logo PIN code
After a correct Logo PIN code 
is entered, the following dialog 
box appears.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the Point 
d button to select “Logo PIN 
code change” and then press the SELECT button. The 
New Logo PIN code input dialog box appears. Set a new 
Logo PIN code.  
Be sure to note the new Logo PIN code and keep it on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting. For details on PIN code 
setting, refer to “PIN code lock” on pages 55–56. CAUTION:
WHEN y
OU HAVE CHANGED THE LOGO 
PIN CODE,  WRITE DOWN  THE NEW PIN 
CODE IN COLUMN OF  THE LOGO PIN 
CODE NO .  MEMO ON PAGE 76,  AND 
KEEP IT SECUREL y . SHOULD  THE LOGO 
PIN CODE BE LOST OR FORGOTTEN, 
THE LOGO PIN CODE SETTING CAN NO 
LONGER BE CHANGED .
Logo PIN code lock
Use the Point 7 8 button to switch On/Off, and then press 
the Point 
d button to move the pointer to “Quit.” Press 
the SELECT button to close the dialog box.
Change the Logo PIN code lock setting
Change the Logo PIN code lock setting
Change the Logo PIN code
Use the Point 7 8 buttons to 
switch On/Off.
Enter a Logo PIN code
Use the Point ed buttons on the top control or Number 
buttons on the remote control to enter a number. 
Use the Point ed buttons on the top control to select a 
number. Press the Point 8 button to fix the number and 
move the red frame pointer to the next box. The number 
changes to “✳.” Repeat this step to complete entering 
a four-digit number. After entering the four-digit number, 
move the pointer to “Set.” Press the SELECT button so 
that you can change the Logo PIN code lock setting.
Press the Number buttons on the remote control to enter 
a number (p.15). When you complete entering a four-digit 
number, the pointer moves to “Set.” Press the SELECT 
button so that you can change the Logo PIN code lock 
setting.
If you fixed an incorrect number, use the Point 7 button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
If you entered an incorrect PIN code, “Logo PIN code” and 
the number (✳✳✳✳) will turn red for a moment. Enter the 
correct PIN code all over again.
When using top control
When using remote control
Setting 
						

							52
Remote controlRemote control
The eight different remote control codes (Code 1–Code 8) 
are assigned to the projector; the factory-set, initial code 
(Code 1) and the other seven codes (Code 2 to Code 8). 
The same code should set on both the projector and the 
remote control. For example, operating the projector in 
“Code 7”, the remote control code also must be switched to 
“Code 7”.
 To change the code for the projector
  Select a remote control code in this Setting Menu.
  To change the code for the remote control:
  Press and hold the MENU button and a number button 
(1–8) on the remote control for more than five seconds to 
switch between the codes. (See page 17 for details.)
RC sensor
Select a location of the infrared remote receiver of the 
remote control. See “Remote Control Operating Range” on 
page 16 for details.
 Both  ....... Activate both the front and back receiver.
  Front  ...... Activate only the front receiver.
  Back  ....... Activate only the back receiver.
Display
This function decides whether to display On-Screen Displays.
  On  ............................  Show all the On-Screen displays. Use 
this function when you want to project 
images after the lamp becomes bright 
enough. The factory default setting is 
in this option.
  Countdown Off  ........ Show the input image instead of 
the countdown when turning on the 
projector. Use this function when you 
want to project the image as early as 
possible even when the lamp is not 
bright enough.
  Off  ...........................  Hide the On-Screen Displays except;
   ●	On-Screen Menu
   ●	“Power off?” (p.25)
   ●	“No signal” for Power management  
   (p.53)
   ●	“Please wait ...”
   ●	Arrows for panning mode (p.46)
   ●	“Filter warning” icon (red) (p.69)
Display
Use the Point 7 8 buttons to 
switch between the options.
Setting 
						

							53
Power management
Time left before the lamp is off.
Press the SELECT button at 
Power management and this 
dialog box appears. Use the 
Point 
7 8 buttons to choose 
one of the three options. 
Press the Point 
d button to 
select the timer, and then use 
the Point 
7 8 buttons to set 
timer.
Power management
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not used for a certain 
period.
If the input signal is interrupted and no button is pressed for 
more than 30 seconds, the timer display with “No signal” 
appears. It starts the countdown until the lamp is turned off. 
The countdown time can be set between 1–30 minutes. 
Use the Point 
7 8 buttons to set the countdown timer.
Select one of the following options:
  Ready  .................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to fast blinking. In this condition, the 
projection lamp can be turned on if the 
input signal is reconnected or any button 
on the top control or remote control is 
pressed. 
  Shut down  ......... When the lamp has been fully cooled 
down, the power will be turned off. 
  Off  .....................  Power management function is off.
On start
When this function is set to “On,” the projector will be 
automatically turned on just by connecting the AC power 
cord to a wall outlet.
✔Note:
	 •	Be	sure	to	turn	off	the	projector	properly	(see	 “Turning	Off	the	Projector”	on	page	25).	If	the	
projector	is	turned	off	in	the	incorrect	sequence,	the	
On	start	function	does	not	work	properly.
✔Note:
	 •	Factory	default	is	 “Ready:	5	min.”
Setting 
						

							54
Fan control
This function is used to set the cooling fans’ operation to the 
projector’s setting environment. Set this function properly in 
accordance with the projector’s installation method. Other wise, 
the cooling fans will not work properly and that causes 
malfunctions of the projector and decreases the lamp life.
Slant
Select the projector’s installation condition from the following 
options:
 Off  ...........  When using the projector within the range of the 
upward/ downward inclination of 20 degrees to the 
horizontal plane.
  L1  ............  When using the projector within the range of 
the upward inclination of over 20 degrees to the 
horizontal plane.*
  L2  ............  When using the projector with downward 
inclination of over 20 degrees to the horizontal 
plane.
Fan control
Key lock
Select Key lock. Use the Point 
ed buttons to choose one of 
the options and select [Yes] 
to activate it.
Security (Key lock and PIN code lock settings)
This function allows you to use the Key lock and PIN code 
lock function to set the security for the projector operation.
Key lock
This function locks the top control and remote control 
buttons to prevent operation by unauthorized persons.
 .....  Unlocked
  .....  Lock all the top control buttons
  .....  Lock the top control buttons except for the 
ON/STAND-BY, INPUT, and INFO. buttons. 
To unlock, use the remote control.
  .....  Lock all the remote control buttons. To 
unlock, use the top control.
  .....  Lock the remote control buttons except for 
the ON, STAND-BY, INPUT 1–3, AUTO PC, 
FREEZE, and INFO. buttons.
Press the SELECT button at Fan 
control and this dialog box appears. 
Use the Point 
ed buttons to choose 
Slant or Highland. Use the Point 
7 
8
 buttons to switch between the 
options.
Highland
Set this function according to the ground elevation under 
which you use the projector. When using the projector 
in high altitudes (about 1,200 meters or more above the 
sea level) where the fans have less cooling effect, set this 
function to “On.”
When “On” is selected, a confirmation box appears. If 
“Yes” is selected, “Please wait...” message appears for 
about 90 seconds and Highland will be set to “On.” If “No” 
is selected, Highland is set to “Off.”
✔Note:
	 •	Make	sure	to	use	the	clean	filter	when	 setting	the	Highland	to	 “On.”
	 •	When	 “Please	wait...”	is	on	the	screen,	
all	operations	are	invalid	except	for	the	
STAND-BY	button	on	the	remote	control	
and	ON/STAND-BY	button	on	the	top	
control.	 When	“STAND-BY”	is	selected,	
Highland	will	be	set	to	off.
If the top control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact the dealer where 
you purchased the projector or the service center.
Setting
+70º
UP
UP
UP
UP
UP
UP
UP
UP
L1
L2 OFF
OFF+20º
-20º
-160º
+160º
Fan control setting
*When installing 
the projector in 
upwardly inclined 
position, install the 
projector bottom 
side up. 
						

							55
Change the PIN code lock setting
Use the Point 7 8 buttons to 
switch between the options.
Use the Point 7 8 button to select Off, On1, or On2 and 
then move the pointer to “Quit” with the Point 
d button. 
Press the SELECT button to close the dialog box.
Change the PIN code lock setting Enter a PIN code
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
  Off  ...........  Unlocked.
  On1  ..........  Enter the PIN code every time turning on 
the projector.
  On2  ..........  Enter the PIN code to operate the projector 
once the power cord is disconnected; as 
long as the AC power cord is connected, 
the projector can be operated without a 
PIN code.
Whenever you change the PIN code lock setting or the 
PIN code (the four-digit number), you are required to 
enter the PIN code. The “1234” is set as the initial PIN 
code at the factory. 
If you want to change the PIN code lock setting, Press 
the SELECT button and the PIN code dialog box appears. 
Enter a PIN code by following the steps below.
PIN code lock
When the projector is locked 
with a PIN code, the PIN code 
lock symbol appears on the 
menu bar. 
Enter a PIN code
After a correct PIN code is 
entered, the following dialog 
box appears.
Use the Point ed buttons on the top control or Number 
buttons on the remote control to enter a number. 
Use the Point ed buttons on the top control to select a 
number. Press the Point 8 button to fix the number and 
move the red frame pointer to the next box. The number 
changes to “✳.” Repeat this step to complete entering 
a four-digit number. After entering the four-digit number, 
move the pointer to “Set.” Press the SELECT button so 
that you can change the PIN code lock setting.
Press the Number buttons on the remote control to enter 
a number (p.15). When you complete entering a four-digit 
number, the pointer moves to “Set.” Press the SELECT 
button so that you can change the PIN code lock setting.
If you fixed an incorrect number, use the Point 7 button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and the 
number (✳✳✳✳) will turn red for a moment. Enter the 
correct PIN code all over again. When using top control
When using remote control
Setting 
						

							56
The PIN code can be changed to your desired four-digit 
number. Press the Point 
d buttons to select “PIN code 
change” and press the SELECT button. The New PIN code 
input dialog box appears. Set a new PIN code.
Change the PIN code Change the PIN code
CAUTION:
WHEN y OU HAVE CHANGED THE PIN 
CODE,  WRITE DOWN  THE NEW PIN 
CODE IN COLUMN OF  THE PIN CODE 
NO .  MEMO ON PAGE 76,  AND KEEP IT 
SECUREL y . IF y OU FORGET y OUR PIN 
CODE,  THE PROJECTOR  CAN NO LONGER 
BE STARTED .
Test pattern
Various test pattern are available for use when setting up the 
projector.
Warning log
This function records anomalous operations while the 
projector is in operation and use it when diagnosing faults. 
Up to 10 warning logs are displayed with the latest warning 
message at the top of the list, followed by previous warning 
messages in chronological order. 
This function is used to reset the lamp counter. 
When the lamp life is left less than 100 hours, the Lamp 
replacement icon appears on the screen, indicating that the 
end of lamp life is approaching.
When replacing the projection lamp, reset the lamp counter. 
See page 60 for operation. Lamp counter 
✔Note:
	 •	When	the	Factory	default	function	is	executed,	all	 the	warning	log	records	will	be	deleted.
This icon appears on the screen when the end of 
lamp life is approaching.
Setting 
						

							57
Factory default
This function returns all setting values except for the user 
logo, PIN code lock, Logo PIN code lock, lamp counter, and 
filter counter to the factory default settings.
Exit the Setting Menu.
Quit
Select Factory default and this 
box appears. Select [Yes], and 
the next box appears. Select [Yes] to 
activate it.
Factory default
This function is used to set a frequency for the filter cleaning.
When the projector reached a specified time between 
cleanings, a Filter warning icon (yellow) appears on the 
screen and the WARNING FILTER indicator lights orange, 
notifying the cleaning is necessary. After cleaning the filter, 
be sure to select RESET and set the timer. The WARNING 
FILTER indicator and Filter warning icon will not turn off until 
the filter counter is reset.
For details about resetting the timer, refer to “Resetting the 
Filter Counter” on page 58.Filter counter 
Filter counter
Use the Point 7 8 buttons to set 
the timer. Select from (Off/100H/ 
200H/300H) depending on the 
use environment.
Filter warning icon (yellow) appears on the screen 
at a set time.
✔Note:
	 •	The	Filter	warning	icon	(yellow)	will	 not	appear	when	the	Display	function	
is	set	to	 “Off”	(p.52),	during	 “Freeze”	
(p.30),	or	 “No	show”	(p.31).
Setting 
						

							58
Turn off the projector, and unplug the AC power cord 
from the AC outlet.
First, clean up the dust on the projector and around the 
air vents.
1
2
Filter prevents dust from accumulating on the optical elements inside the projector\
. Should the filter becomes 
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and 
adversely affect the life of the projector. If a “Filter warning” icon (yellow or red) appears on the screen and the 
WARNING FILTER indicator lights or blinks, clean the filter immediately. Clean the filter by following the steps 
below.
Pull out the filter cover from the projector and then 
remove the filter.3
Reinstall the filter into the projector properly.5
CAUTION
Do not operate the projector with the filter 
removed. Dust may accumulate on the optical 
elements degrading picture quality.
Do not put anything into the air vents. Doing so 
may result in malfunction of the projector.
Gently clean the filter by using a brush or blower.
WARNING: Do not wash the filter with water and 
any other liquid matter . Otherwise the filter may be 
damaged .4
Reset the filter counter in the Setting Menu. See 
“Resetting the Filter Counter” below.6
Press and hold the 
filter cover and pull 
out the filter.
Filter coverFilter
Filter
Filter cover
Be sure to reset the Filter counter after cleaning or replacing the filter. 
Press the MENU button to display the On-Screen 
Menu. Use the Point 
7 8 buttons to move the red 
frame pointer to the Setting Menu icon.
Use the Point ed buttons to move the red frame 
pointer to Filter counter and then press the SELECT 
button. A dialog box appears showing the total 
accumulated time of the filter use, a timer setting 
option, and the reset option. Select Reset and the 
“Filter counter Reset?” appears. Select [Yes] to 
continue.
1
2
Resetting the Filter Counter
Filter counter
NOTE:  If the filter is heavily clogged and unable to 
clean, replace it with a new one. Consult 
your dealer for details.
Replacement Filter Part No  .: 910-330-7184
Select Reset and the “Filter 
counter Reset?” appears.
Select [Yes], 
then another 
confirmation 
box appears.
Select [Yes] again to reset 
the Filter counter.
Another confirmation dialog box appears, select [Yes] 
to reset the Filter counter.3
Cleaning the Filter
Maintenance and Filter Cleaning 
						

							59
When the projection lamp of the projector reaches its end 
of life, the Lamp replacement icon appears on the screen 
and LAMP REPLACE indicator lights yellow. Replace the 
lamp with a new one promptly. The timing when the LAMP 
REPLACE indicator should light is depending on the lamp 
mode.
Follow these steps to replace the lamp.
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the dealer.
	●	Model No . of your projector  :  LC-SXG400, LC-SXG400L
	● Replacement Lamp Type No  . :  POA-LMP116  (Service Parts No. 610 335 8093)
For continued safety, replace with a lamp of the same 
type lamp. Do not drop the lamp or touch the glass 
bulb! The glass can shatter and may cause injury.Allow a projector to cool for at least 45 minutes 
before you open the Lamp cover. The inside of 
the projector can become very hot.
CAUTION
Turn off the projector and unplug the AC power cord. 
Let the projector cool for at least 45 minutes.
Remove the two (2) screws that secure the lamp. Lift 
the lamp out of the projector by using the handle.
1
3
Replace the lamp with a new one and secure the two 
(2) screws. Make sure that the lamp is set properly. 
Put the lamp cover back and secure it with the screw.4
Remove the screw that secures the lamp cover, and 
then open the lamp cover.2
Connect the AC power cord to the projector and turn 
on the projector.
6Reset the lamp counter  .
See “Resetting the Lamp Counter” on the next page.
5
Lamp Replacement
CAUTION
Screw
Lamp replacement icon
WARNING: 
TURN OFF 
THE UV LAMP BEFORE 
OPENING  THE LAMP COVER
Top Control
Handle
Screws
LAMP REPLACE
indicator
Lamp cover
Maintenance and Filter Cleaning 
						

							60
Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP 
REPLACE indicator stops lighting and the Lamp replacement icon disappears.
Press the MENU button to display the On-Screen 
Menu. Use the Point 
7 8 buttons to move the red 
frame pointer to the Setting Menu icon.
Use the Point ed buttons to move the red frame 
pointer to Lamp counter and then press the SELECT 
button. A dialog box appears showing the total 
accumulated time of the lamp usage and the reset 
option. Select Reset and the “Lamp replacement 
counter Reset?” appears. Select [Yes] to continue.
1
2
Another confirmation dialog box appears, select [Yes] 
to reset the Lamp counter.3
This projector uses a high-pressure lamp which must be handled carefully and properly.  
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee  of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  life  in  a  shorter  period  of  time 
than other similar lamps.
●  If  the  projector  indicates  that  the  lamp  should  be  replaced,  i.e.,  if  the  LAMP  REPLACE  indicator  lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
    (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of 
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
●  A  Lamp  may  explode  as  a  result  of  vibration,  shock  or  degradation  as  a  result  of  hours  of  use  as  its 
lifetime  draws  to  an  end.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFET y PRECAUTIONS SHOULD BE TAKEN .
If  a  lamp  explodes,  disconnect  the  projector’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  station  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
          LAMP HANDLING PRECAUTIONS
Resetting the Lamp Counter
✔Note:
	 •	Do	not	reset	the	Lamp	counter	without	implementing	 lamp	replacement.	Be	sure	to	reset	the	Lamp	counter	
only	after	replacing	the	lamp.
Select [Yes], 
then another 
confirmation 
box appears.
Select [Yes] again to reset 
the Lamp counter. Select Reset and the “Lamp 
replacement counter Reset?” 
appears.
Lamp counter
Maintenance and Filter Cleaning