Eiki Projector Lc Se10 User Manual

							11
Part Names and Functions
This projector has control buttons and indicators on its top.
To p
qw
e
r
t
y
u
i
o
iLAMP REPLACE indicatorTurns yellow when the life of the projection lamp draws to an
end.  (p45, 49)
uWARNING indicatorLights red when the projector detects abnormal condition.  This
also flashes red when the internal temperature of the projector
exceeds the operating range.  (p43, 49)
qPOWER ON–OFF buttonTurns the projector on or off.  (p19)
yPOWER indicatorFlashes red until the projector gets ready to be turned on.  It
turns red when the projector is in the stand-by mode.  It
remains green while the projector is under operation. (p49)
!2INPUT buttonSelects input source. (p25, 33)
!0MENU buttonOpens or closes the On-Screen Menu. (p23)
oPOINT (Up/Down/Left/Right ) buttonSelects an item or adjusts value in the On-Screen Menu.  These
are also used to pan the image in the Digital zoom +/– mode.
(p32)
Point Left/Right button are  used as VOLUME +/– button.  (p22)
!1SELECT buttonExecutes the item selected.  It is also used to expand /
compress the image in Digital zoom +/–  mode. (p32)
!0!1!2
wAUTO SET UP buttonOperate AUTO SET UP function. (p21)
eZOOM/FOCUS buttonSelect ZOOM or FOCUS function. (p20)
rIMAGE buttonSelect image level. (p30, 36)
tAUTO PC ADJ. buttonOperates the AUTO PC Adjustment function. (p27) 
						

							12
Part Names and Functions
MUTE PAGEFREEZE D.ZOOMNO SHOW
ON RESETALL OFFCOMPUTER 1 LASER
FOCUS KEYSTONE
ZOOMCOMPUTER 2
VIDEO MENU
R-CLICKSELECT
IMAGE
AUTO SETP-TIMER AUTO PCON
-OFF
VOLUME-VOLUME+











Remote Control
q
w
e
r
t
y
u
i
o
!0
!1
!4
!5
!6
!7
!8
!9
@0
!2
@1
@5RESET/ON/ALL-OFF switchWhen using the remote control, set this switch to “ON.” Set it to “ALL OFF” for
energy saving when it is not used.  Slide this switch to the RESET to initialize the
remote control code.  (p14)
wSIGNAL EMISSION indicatorThis indicator lights red while the laser beam is being emitted from the laser light
window or a signal is being sent from the remote control to the projector.
eAUTO PC buttonOperates the Auto PC adjustment function. (p27)
rD.ZOOM buttonsSelects the Digital zoom +/– mode and resize the image. (p32)
!8MUTE buttonMutes sound. (p22)
iPOINT (UP/DOWN/LEFT/RIGHT) buttonsSelects an item or adjusts value in the On-Screen Menu. These are also used to pan
the image in the Digital zoom +/- mode. (p32)
Point Left/Right button are also used as VOLUME +/- button. (p22)
!0MENU buttonOpens or closes the On-Screen Menu.  (p23)
@4LASER buttonOperates the Laser pointer function.  Laser beam is emitted while pressing this
button within 1 minute.  When using this laser pointer for more than 1 minute,
release the LASER button and press it again.  This button is also used as a
switching button to activate the Pointer function of the projector.  (p13)
!5POWER ON-OFF button Turns the projector on or off. (p19)
!6NO SHOW buttonTurns the picture into black image. (p22)
tFREEZE buttonFreezes the projected picture. (p21)
yIMAGE buttonSelects image levels.(p30, 36)
!2SELECT buttonExecutes the item selected, or to expand or compress image in the Digital zoom +/-
mode. (p32)
@1 @2 @3COMPUTER 1, COMPUTER 2, VIDEO buttonsSelects input source (COMPUTER 1, COMPUTER 2 or VIDEO).  (p25, 33)
!7P-TIMER buttonOperates P-Timer function. (p22) 
uPAGE UP/DOWN buttonsTurns pages; the Up button to the previous page and the Down button to the next
page for an image from a computer.  Connect the projector and your computer with
a USB cable before use.  (p17)
@0R-CLICK buttonActs as right click for wireless mouse operation.  (p14)
qL-CLICK buttonActs as left click for wireless mouse operation. (p14)
!1KEYSTONE buttonCorrects keystone distortion. (p20, 21, 39)
oPRESENTATION POINTER buttonMove a pointer of the projector or a pointer for wireless mouse operation. (p13, 14)
@4!3@3
@5
@2
!3ZOOM buttons Adjust zoom. (p20)
!4FOCUS buttons Adjust focus. (p20)
!9AUTO SET UP buttonOperate AUTO SET UP function. (p21) 
						

							13
Part Names and Functions
MUMUTE PAGEFREEZE D.ZOOMNO SHOW
ON RESET ALL OFF
COMPUTER 1 LASER
FOCUS
KEYSTONE
ZOOMCOMPUTER 2
VIDEO
MENUMENUR-CLICKSELECT
IMAGE
AUTO SETP-TIMER AUTO PCON
-OFF
VOLUME-VOLUME+





You can move Spotlight or Pointer of the projector with the remote control to emphasize a part of the projected image.
(See “Pointer” on page 41 for changing the patterns and sizes.)
While pressing the MENU button, hold down the NO SHOW
button for more than 7 seconds so that the Pointer function
can be available. (The Laser pointer function has switched to
the Pointer function.)1
Spotlight
Press the LASER button on the remote control toward the
projector and see if the LASER button lights green, and
Spotlight or Pointer is displayed on the screen.  Then you can
move Spotlight or Pointer with the PRESENTATION
POINTER button.  If the LASER button does not light green
and still emits laser beam, the Laser pointer function has not
switched to the Pointer function yet.  Try these steps until
the LASER button lights green. 2
Pointer Function
To clear Spotlight or Pointer displayed on the screen, press
the LASER button toward the projector and see if the LASER
button turns off.
To use the Laser pointer function once again, while pressing
the MENU button, hold down the NO SHOW button for
more than 7 seconds.3
MUMUTE PAGEFREEZE D.ZOOMNO SHOW
ON RESET ALL OFF
COMPUTER 1 LASER
FOCUS
KEYSTONE
ZOOM
COMPUTER 2
VIDEO
MENUMENUR-CLICKSELECT
IMAGE
AUTO SETP-TIMER AUTO PCON
-OFF
VOLUME-VOLUME+





After the Laser pointer function  has
switched to the Pointer function, the
LASER button is used as the Pointer
function ON-OFF switch instead of the
Laser pointer function. 
Press the LASER button toward the
projector and see if it lights green.
Pointer
This remote control emits a laser beam as Laser pointer function from the laser light window.  When the LASER button is
pressed, laser light goes on.  When the LASER button is being pressed for more than 1 minute or the LASER button is
released, light goes off.  The signal emission indicator lights red and laser is emitted with red light to indicate laser beam is
being emitted.
The laser emitted is a class 
IIlaser; therefore, do not look into the laser light window or shine the laser beam on yourself or
other people.  The marks below are caution labels for laser beam.
CAUTION:  Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.  Do not look into the laser light window while laser is emitting, otherwise eye
damage may result. 
Laser Light Window
These caution labels are put on the remote control.
Signal Emission Indicator
Laser Pointer Function
NO SHOW button (2)
MENU button (1)
LASER button (3)
PRESENTATION POINTER button (4)
PRESENTATION POINTER button (4)
NOTE
You can choose the size of Spotlight (Large, Middle, and Small) and the
pattern of Pointer (Arrow, Finger, and Dot) in the Setting Menu.  See
“Pointer” on page 41. 
						

							14
Part Names and Functions
This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8).  This switching function prevents remote control interference when operating several
projectors or video equipment at the same time.  (Change the remote control code for the projector first before changing
that for the remote control.  See “Remote control” on page 42.) 
While pressing the MENU button, press the IMAGE button
number of times corresponding to each remote control code
number.  Each time you press the IMAGE button, the code is
changed sequentially.  (See the list below.) 1
To initialize the remote control code for the remote control,
slide the RESET/ON/ALL-OFF switch to the RESET, and then
to the ON.  The initial code is Code 1.2
Remote Control Code
MUMUTE PAGEFREEZE D.ZOOMNO SHOW
ON RESETALL OFFALL OFF
COMPUTER 1 LASERASER
FOCUSFOCUS
KEYSTONEYSTONE
ZOOMCOMPUTER 2
VIDEO MENU
MENUR-CLICKSELECT
IMAGE
AUTO SETP-TIMERIMER
AUTO PCON-OFF
VOLUME-VOLUME+






While pressing the MENU button,
press the IMAGE button number of
times corresponding to the remote
control code for the projector. 
Remote Control CodeNumber of Times of
Pressing IMAGE Button
Code 1 1
Code 2 2
Code 33
Code 44
Code 55
Code 66
Code 77
Code 88
MENU button IMAGE button
The remote control can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect
your computer and the projector with the supplied USB cable.  (See page 17 for connection.)  When the Pointer function is
used, the wireless mouse is not available. 
Wireless Mouse Operation
MUTE PAGEFREEZE D.ZOOM NO SHOW
ON RESET ALL OFF
COMPUTER 1 LASER
FOCUS
KEYSTONE
ZOOM
COMPUTER 2
VIDEO
MENUR-CLICKSELECT
IMAGE
AUTO SETP-TIMER AUTO PC ON
-OFF
VOLUME-VOLUME+




Move the pointer on the screen
with this button.  PRESENTATION POINTER button
R-CLICK button
L-CLICK button
Acts as right click while the
projector and a computer are
connected with a USB 
cable.            Acts as left click while the
projector and a computer are
connected with a USB 
cable.            
RESET/ON/ALL-OFF switch 
						

							15
Part Names and Functions
To insure safe operation, please observe the following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
Risk of explosion if battery is replaced by an incorrect type. 
Dispose of used batteries according to the instructions.  
Press the lid down-
ward and slide it.
Remove the battery
compartment lid.Slide the batteries into
the compartment.Replace the compartment
lid.
Two AA size batteriesFor correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
12 3
Point the remote control toward the projector (Infrared Remote Receiver) whenever pressing any button.  Maximum
operating range for the remote control is about 16.4’ (5m) and 60°in front of the projector.
16.4’
(5 m)
60°
Remote Control Batteries Installation
Remote Control Operating Range
60° 16.4’
(5 m) 
						

							16
Installation
Projection angle can be adjusted up to 10.3 degrees with the adjustable feet. 
Lift the front of the projector and pull the feet lock latches on
both sides of the projector.1
Adjustable FeetFeet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be adjusted
by menu operation.  (p20, 21, 39)3
CAUTION
Tilt the projector within the adjustable range in order not to shorten
the life of the lamp.  Proper angle should be taken.  See page 5. 
Positioning the Projector
Adjustable Feet
100”150”231”300”
231”
178”
115”
77”
40”
 A
B
31”
33.1 (10.1m)
25.3 (7.7m)
16.4 (5.0m)
10.8 (3.3m)
Max. Zoom
Min. Zoom
A : B  =  9 : 1
Screen Size
(W x H) mm
4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x 610
5.6 (1.7m)
4.3 (1.3m)
100”
2032 x 1524
14.4 (4.4m)
10.8 (3.3m)
150”
3048 x 2286
21.7 (6.6m)
16.4 (5.0m)
231”
4694 x 3520
33.1 (10.1m)
25.3 (7.7m)
300”
6096 x 4572 
––-––
33.1 (10.1m)
(Inch Diagonal)
4.3 (1.3m)
NOTE
 The brightness in a room has a great influence on picture quality.  It is
recommended to limit ambient lighting in order to provide the best
image.
 The values shown are approximate and may vary from the actual size. 
This projector is designed to project on a flat projection surface and can be focused from 4.3’(1.3m) - 33.1’(10.1m).  Refer to
the figure and the table below for the screen size and the distance between the projector and the screen.
(Center) 
						

							17
Installation
Connecting to a Computer
S - VIDEO
USB
USB COMPUTER  IN  2  /
SERVICE PORT COMPUTER  IN  1 
DVI - I
MCI R  -  AUDIO  IN  -  L
AUDIO  IN  1 AUDIO  IN  2
(MONO)
VIDEO / Y – Pb/Cb  –  Pr/Cr
MONITOR  OUT
AUDIO OUTRESET
(VARIABLE)
ON ON
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF
ON
ONOFF OFF OFF
OFF OFF OFF
OFF OFF OFF34 56
OFF OFF ON ON 21 MODE (1152 x 870)
ON ON
ON
ON OFF
OFF12
ON ON
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
DVI-VGA Cable 
Monitor Output
Desktop type Laptop type
Audio Speaker
(stereo) Audio Amplifier
Audio Cable
(stereo) ✽
Audio Output
Audio Input
AUDIO OUT
COMPUTER 
AUDIO  IN 
Cables used for connection(✽= These accessories are not supplied with this projector.)
Audio 
Cable ✽(stereo)
NOTE :When connecting the cable, the power
cords of both the projector and the
external equipment should be
disconnected from AC outlet.  
USB port
MAC Adapter ✽Set slide switch-
es according to
the chart below.
• VGA Cable (HDB 15 pin) ✽
• DVI-VGA Cable (HDB 15 pin) 
• DVI-Digital Cable (for Single Link T.M.D.S.) 
✽
• USB Cable
• MAC Adapter (When connecting to Macintosh computer)
✽
• Audio Cables ( Mini Plug (stereo) x 2)✽
External Audio Equipment
Terminals 
of the Projector
VGA 
Cable ✽
Monitor Output
or
Monitor Input
USBCOMPUTER IN 2 /
MONITOR OUT
Set switches as shown in the table
below depending on RESOLUTION
MODE that you want to use before
you turn on projector and computer.
MAC ADAPTER (Not supplied)
USB 
Cable 
COMPUTER IN 1 DVI-I
DVI Cable ✽
Monitor Output
COMPUTER IN 1 DVI-I
NOTE
This terminal is switchable. Set the terminal
up as either Computer input or Monitor
output before using this terminal.  (See Page
40.) 
						

							18
Installation
Connecting to Video Equipment
S - VIDEO
USB
USB COMPUTER  IN  2  /
SERVICE PORT COMPUTER  IN  1 
DVI - I
MCI R  -  AUDIO  IN  -  L
AUDIO  IN  1 AUDIO  IN  2
(MONO)
VIDEO / Y – Pb/Cb  –  Pr/Cr
MONITOR  OUT
AUDIO OUTRESET
(VARIABLE)
Video Source (example)
Video Cassette RecorderVideo Disc Player
S-VIDEO
Cable 
✽
Audio AmplifierAudio Speaker 
(stereo) Audio Cable 
(Stereo) 
✽
Terminals 
of the Projector
S-VIDEO
Output
Audio Input
• Video Cable (RCA x 1) ✽
• Video Cable (RCA x 3) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini Plug (stereo) x 2 or RCA x 2) ✽
• Scart-VGA Cable ✽                                                                  
NOTE :
When connecting the cable, the power
cords of both the projector and the
external equipment should be
disconnected from AC outlet. 
Audio Output
Audio Cable
(Stereo) ✽
External Audio Equipment
AUDIO IN S-VIDEO
VIDEO
AUDIO OUT
Component video output equipment. (such as DVD player or high-definition TV source.)
Component Video Output
(Y, Pb/Cb, Pr/Cr) Composite 
Video Output
Video Cable
(RCA x 1) ✽Scart-VGA
Cable 
✽ 
RGB Scart
21-pin Output
Cables used for connection(✽= These accessories are not supplied with this projector.)
Video Cable
(RCA x 3) ✽Audio Cable
(RCA x 2) ✽
Audio Output
(R, L)
AUDIO INCOMPUTER IN 2 /
MONITOR OUT
NOTE
The Y, Pb/Cb, Pr/Cr jacks has priority over the S-VIDEO jack
under the condition of connecting both the Y, Pb/Cb, Pr/Cr
jacks and the S-VIDEO jack  when selecting AUTO in the Input
Menu. 
The S-VIDEO jack has priority over the VIDEO jack under the
condition of connecting both the S-VIDEO jack and the VIDEO
jack  when selecting AUTO in the Input Menu. 
Select COMPUTER 2 in the Setting Menu when the
COMPUTER IN 2/MONITOR OUT terminal is used as RGB
Scart 21-Pin video input .  (See “Terminal” on page 40.)
COMPUTER IN 1 DVI-I
Digital Video Output
✽ 
						

							19
Basic Operation
Connect the projectors AC power cord into an AC outlet.  The
POWER indicator flashes red in a moment and turns on red. 
Press the POWER ON-OFF button on the top control or on the
remote control.  The POWER indicator turns green, and the
cooling fans start to operate.  The preparation display appears on
the screen and the count down starts.  (A captured image can
be used as the preparation display.  See “Capture” on page 40.) 
2
3
Press the POWER ON-OFF button on the top control or on the
remote control, and a message Power off? appears on the
screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to flash red, and it
continues while the cooling fans are operating (for about 90
seconds). 
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD  WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED.  OTHERWISE IT WILL RESULT
IN SHORTENING LAMP LIFE.
1
3When the projector has cooled down enough to be turned on
again, the POWER indicator lights red.  Then you can disconnect
the AC power cord.
26
The preparation display disappears after 30 seconds.
The message disappears after 4 seconds.
4After the count-down, the input source that was selected last
and the Lamp mode status icon appear on the screen. 
(See page 41 for Lamp mode.)
Selected Input Source and Lamp Mode
Turning On the Projector
Turning Off the Projector
NOTE
The projector cannot be turned on during the cooling period with the
POWER indicator flashing red.  You can turn it on again after the POWER
indicator lights red.
When the On start function is on, this projector is turned on automatically by
connecting the AC power cord to an AC outlet.  (See page 41 for the On
start function.) 
Do not use the projector for more than 24 hours continuously.  Turn off the
projector at least once in 24 hours and give it a rest.  Continuous use may
result in shortening the lamp lifetime.  
This projector monitors internal temperature and automatically controls the
running speed of the cooling fans. 
If the WARNING indicator flashes or lights red, see “Warning Indicator” on
page 43.
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.  
Lamp mode 
						

							20
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Basic Operation
•The arrows are white when there is no correction.
•The direction of the arrow being corrected turns red.
•The arrows disappear at the maximum correction.
•If you press the KEYSTONE button on the remote control once more
while the keystone adjustment icon is being displayed, the keystone
adjustment will be canceled.
Keystone Adjustment
Zoom Adjustment
Focus Adjustment
Reduce the upper width
with Point Up button. Reduce the lower width
with Point Down button.  Reduce the left part with
Point Left button.  Reduce the right part with
Point Right button.  
1Press the KEYSTONE button on the remote control or select
Keystone in the Setting Menu (p39).  The keystone dialog box
appears. Press the Point UP/DOWN button to move the red
arrow pointer to H-V and then press the SELECT button. The
keystone adjustment icon appears.
2Correct keystone distortion by pressing the Point
Up/Down/Left/Right button.  Press the Point Up button to
reduce the upper part of the image, and press the Point Down
button to reduce the lower part.  Press the Point Left button to
reduce the left part, and press the Point Right button to reduce
the right part.  
Keystone adjustment can be memorized.  (p39)
Message disappears after 4 seconds.
Zoom
Focus
1Press ZOOM/FOCUS button on Top Control or ZOOM /
button on Remote Control Unit.  The message “Zoom” is
displayed.
2Press ZOOM button or POINT UP button to make image
larger, and press ZOOM 
button or POINT DOWN button to
make image smaller.
1Press ZOOM/FOCUS button on Top Control or FOCUS /
button on Remote Control Unit.  The message “Focus” is
displayed.
2Adjust focus of image by pressing FOCUS /button or POINT
UP/DOWN button(s) .
Message disappears after 4 seconds.
Keystone correction (H-V)