Eiki Projector Lc Se10 User Manual

41
Setting
For reducing power consumption as well as maintaining the lamp life,
the Power management function turns off the projection lamp when
the input signal is interrupted and no button is pressed for 30 seconds
or more.
When the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message No signal
appears on the screen. The count-down starts for the time to have
been set.  The count-down time can be set between 1 and 30
minutes. 
When the...

42
Setting
This function is used to reset the lamp replace counter.  When
replacing the projection lamp, reset the lamp replace counter by
using this function.  See page 46 for operation.Lamp counter reset Remote control
This projector provides eight different remote control codes (Code 1-
Code 8); the factory-set, initial code (Code 1) and the other seven
codes (Code 2 to Code 8).  This switching function prevents remote
control interference when operating several projectors or video
equipment at the...

43
The WARNING indicator shows the state of the function which protects the projector.  Check the state of the WARNING
indicator and the POWER indicator to take proper maintenance. 
WARNING
flashing red
TOP CONTROL
Warning Indicator
The projector is shut down and the WARNING indicator is flashing red
When the temperature inside the projector exceeds the normal
temperature, the projector is automatically shut down to protect the
inside of the projector.  The POWER indicator is flashing and the
projector...

44
Maintenance and Cleaning
Disconnect the AC power cord before cleaning.
When the projector is not in use, replace the lens cover.
1
3
2
Follow these steps to clean the projection lens.
Air Filter
Pull up and remove.
Turn off the projector, and disconnect the AC power cord from
the AC outlet.
Turn the projector upside down and remove the air filters by
pulling the latches upward.
1
2
Air filters prevent dust from accumulating on the surface of the optical elements inside the projector.  Should the air...

45
When the life of the projection lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow.  If this indicator lights
yellow, replace the lamp with a new one promptly.
Follow these steps to replace the lamp.
Lamp Lamp Cover
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give the following
information to the dealer.
Model No. of your projector   : LC-SE10
Replacement Lamp Type No. : POA-LMP68
(Service Parts No. 610...

46
Maintenance and Cleaning
Be sure to reset the lamp replace counter after the lamp is replaced.  When the lamp replace counter is reset, the LAMP
REPLACE indicator stops lighting.
Turn the projector on, press the MENU button and the On-
Screen Menu will appear.  Press the Point Left/Right button
to move the red frame pointer to the Setting Menu icon.
Press the Point Down button to move the red frame pointer
to the Lamp counter reset item and then press the SELECT
button.  The message Lamp replace...

47
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described in Connecting to a Computer
and “Connecting to Video Equipment” on  page17 and 18. 
–Make sure all equipment is connected to AC outlet and the power is turned on.
–When you operate the projector with a computer and it does not project an image, restart the computer.  
No power–Plug the power cord of the...

48
Appendix
This symbol on the nameplate means the product is Listed by Underwriters Laboratories
Inc.  It is designed and manufactured to meet rigid U.L. safety standards against risk of
fire, casualty and electrical hazards.
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If problems still persist after following all operating instructions,
contact the dealer where you purchased the projector or the
service center.Give the model number and explain about...

49
Appendix
Check the indicators for projector condition.  
• • • lights green.• • • lights red.• • • off• • • flashes green.
✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.  When this indicator lights
yellow, replace the projection lamp with a new one promptly.  Reset the Lamp replace counter after replacement of the lamp.  
See page 45 and 46.
The projector is OFF.  (The AC power cord is unplugged.)
The projector is preparing for stand-by or the...

50
Appendix
Menu Tree
System (1)MODE 1MODE 2SVGA 1- - - -
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClampDisplay area
Display area - HDisplay area - VFull screenResetMode freeStore
Quit
StandardRealImage 1Image 2Image 3Image 4
Image AdjustContrastBrightnessColor Temp
RedGreenBlue
Gamma
Store
Quit
NormalTrueWideDigital zoom +Digital zoom –
0 - 31
On/Off
0 - 630 - 63
InputRGB( Analog )  
RGB( PC Digital )  
Go to System(1)
Computer 2RGB
Y, Pb/Cb, Pr/Cr
Go to System(1)
Computer Input...