Eiki Projector Lc Se10 User Manual

21
Basic Operation
Press the FREEZE button on the remote control to freeze the picture
on the screen.  To cancel the FREEZE function, press the FREEZE
button again or press any other button.
Picture Freeze Function
MUTE PAGEFREEZE D.ZOOMNO SHOW
ON RESET ALL OFFCOMPUTER 1 L ASER
FOCUS KEYSTONE
ZOOMCOMPUTER 2
VIDEO MENU
R-CLICKSELECT
IMAGE
AUTO SETP-TIMER AUTO PCON
-OFF
VOLUME-VOLUME+


FREEZE button
1Press the Point UP/DOWN button to move the red arrow pointer
to Corner and then press the SELECT button....

22
Basic Operation
Press the NO SHOW button on the remote control to black out the
image.  To restore to normal, press the NO SHOW button again or
press any other button.  When a projected image is captured and set
as “User” in the Logo item in the Setting Menu (p40), the screen
changes each time you press the NO SHOW button as follows.
The message disappears after 4 seconds.
Press the P-TIMER button on the remote control.  The timer display
“00 : 00” appears on the screen and the timer starts to count...

23
Basic Operation
Press the MENU button to display the On-Screen Menu
(Menu bar).  A red frame is a pointer.
Move the pointer (red frame) to the Menu icon that you want
to select by pressing the Point Left/Right button.
Adjust the item data by pressing the Point Left/Right button.
Refer to the following pages for details of respective
adjustments.
Press the Point Down button and move the pointer (red
frame or red arrow) to the item that you want to adjust, and
then press the SELECT button to show the...

24
Basic Operation
Menu Bar
PC System Menu
Used to select
computer system.
(p26)
Image Adjust Menu
Used to adjust computer image. [Contrast / Brightness / Color
temp. / 
White balance (R/G/B) /Sharpness / Gamma](p31)
Setting Menu
Used to change
settings of the
projector or reset  lamp
replace counter. 
(p39-42)
Sound Menu
Used to adjust
volume or mute
sound.  (p22)
Image Select Menu
Used to select  an
image level among
Standard, Real,
and Image 1 ~ 4.
(p30)
For computer source
AV System Menu
Used to...

25
Choose either Computer 1 or Computer 2 by pressing the INPUT
button on the top control or press the COMPUTER 1 or COMPUTER 2
button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Press the MENU button and the On-Screen Menu will appear.
Press the Point Left/Right button to move the red frame pointer
to the Input Menu icon.1
Move the pointer (red arrow)
to Computer 1 and press the
SELECT button.
Computer
1
Move the...

26
Computer Input
This projector can detect most of the current computer systems with the Multi-scan system and the Auto PC adjustment
function provided in the projector.  When selecting computer input, the projector automatically displays the most proper
image for the input signal.  One of the following four displays appears on the system menu icon.  If the projector does not
tune the input signal and the projected image is not displayed properly, or when you wish to adjust it manually, perform
manual...

27
Computer Input
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to
your computer.  Auto PC Adjustment function can be operated as follows.
Press the MENU button and the On-Screen Menu will appear.
Press the Point Left/Right button to move the red frame pointer
to the PC Adjust Menu icon.1
2Press the Point Down button to move the red frame pointer to
the Auto PC Adj. icon and then press the SELECT button twice.
This Auto PC...

28
Computer Input
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.  This
projector has Manual PC Adjustment to enable you to precisely adjust several parameters to match those signal formats.
The projector has 5 independent memory areas to memorize those parameters manually adjusted.  This enables you to
recall the setting for a specific computer whenever you use it. 
Press the MENU button and the On-Screen Menu will appear.
Press the Point...

29
Computer Input
Select the resolution at the Display area dialog box.
Display area
Adjusts the horizontal area displayed by this projector.  Press the
Point Left/Right button to decrease/increase value and then press the
SELECT button.
Display area H
Adjusts the vertical area displayed by this projector.  Press the Point
Left/Right button to decrease/increase value and then press the
SELECT button.
Display area V
When this function is on, SXGA image is fully displayed at 4 : 3 aspect
ratio.  It is...

30
Computer Input
Press the MENU button and the On-Screen Menu will appear.
Press the Point Left/Right button to move the red frame pointer
to the Image Select Menu icon.1
2Press the Point Down button to move the red frame pointer to
the level that you want to set and then press the SELECT
button.
Move the red frame pointer to
the level and press the
SELECT button.
The level being selected.
Image Select Menu
Normal picture level preset on this projector.
Standard
Picture level with improved halftone for...