Eiki Projector Lc Sd15 User Manual

							21
Basic Operation
Menu Bar
PC System Menu
Select computer
system. (p25)
Image Adjust Menu
Adjust the computer image. [Contrast / Brightness / Color
temp. / 
White balance (R/G/B) /
Gamma](p30)
Setting Menu
Change the settings
for the projector or
reset the lamp
replacement counter. 
(p38-44)
Sound Menu
Adjust the volume
or mute the sound.
(p23)
Image Select Menu
Select  an image level
among Dynamic,
Standard, Real,
Blackboard(Green), and
Image 1 ~ 4. (p29)
For computer source
AV System Menu
Select system of
selected video
source. (p33)
Image Adjust Menu
Adjust the picture image.  [Contrast / Brightness / Color / Tint /
Color temp. / White balance (R/G/B) /
Sharpness /Gamma / Progressive /
Film]
(p35-36)
For video source
Same function as Menu
for computer source.
Input Menu
Select either Video
or Computer for
input source. (p32)
PC Adjust Menu
Adjust parameters
to match with input
signal format.  
(p26-28)
Image Select Menu
Select an image level
among Dynamic,
Standard, Cinema,
Blackboard(Green) and
Image 1 ~ 4. (p34)
Screen Menu
Set the size of
image to Normal
or Wide. (p37)
Guide Window
Show the selected
Menu of the On-
Screen Menu.
Same function as
Menu for computer
source.
Input Menu
Select either
Computer or Video
for input source.
(p24)
Screen Menu
Adjust the size of
image.  [Normal /
True / Wide /
Digital zoom +/–]
(p31)
Basic Operation 
						

							Press the NO SHOW button on the remote control to black out the
image. To restore to normal, press the NO SHOW button again or
press any other button. When a projected image is captured and
set as “User” in the Logo item in the Setting Menu (p40), the
screen changes each time you press the NO SHOW button as
follows.
The message disappears after 4 seconds.
black-out ➜the captured image ➜normal ➜• • • • •
No Show Function
22
Basic Operation
Press the FREEZE button on the remote control to freeze the
picture on the screen. To cancel the Freeze function, press the
FREEZE button again or press any other button. 
1Press the KEYSTONE button on the remote control or select
Keystone on the Setting Menu (p38) to display the Keystone
dialog box.
2Correct keystone distortion by pressing the Point edbuttons.
Press the Point 
ebutton to reduce the upper part of image, and
press the Point 
dbutton to reduce the lower part.  
Reduce the upper width with the Point ebutton.  Reduce the lower width with the Point dbutton.  
If a projected picture has keystone distortion, correct the image with the keystone correction function.
–The arrows are white when no correction.
–The arrows in the corrected direction will turn
red.
–The arrows disappear at the maximum
correction.
–If you press the KEYSTONE button on the
remote control once more while the keystone
dialog box is being displayed, the correction
will be canceled.
Remote ControlKEYSTONE
button
FREEZE
button
NO SHOW
button
The Dim mode function is provided to dim the contrast and
brightness of the projection screen. Press the DIM button on the
remote control to dim the screen. Press the DIM button again to
return to the previous screen. Contrast level of the Dim mode
screen can be adjusted in the Setting Menu.  (p41)
DIM
button
Dim Mode Picture Freeze Function Keystone Correction 
						

							23
Basic Operation
1
2
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the Sound Menu icon.  Volume
Press the VOLUME +/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Press the + button to turn up the volume and the – button to turn
down the volume.
Mute
Press the MUTE button on the remote control to turn off the
sound. To restore the sound to its previous level, press the MUTE
button again or press the VOLUME +/– buttons.
Press the Point 8button to turn up the volume, and press the
Point 
7button to turn down the volume. 
Press the Point 7 8buttons to turn off the sound. The mute dialog
box display is changed to “On” and the sound is turned off. To
restore the sound to its previous level, press the Point 
7 8
buttons again.
Press the Point dbutton to move the red frame pointer to
the desired item and then press the SELECT button.
Approximate level
of the volume.
Exit the Sound Menu.
Direct Operation
Volume
Mute
Approximate level of the volume
Press the MUTE button to set
the Mute function On or Off.
The display disappears after 4 seconds.  
Sound Menu
Sound Menu icon
Sound Adjustment
Menu Operation
Press the P-TIMER button on the remote control. The timer
display “00 : 00” appears on the screen and starts to count time
(00 : 00 ~ 59 : 59).  
To stop the P-Timer, press the P-TIMER button. Press the P-
TIMER button again to cancel the  P-Timer function.
P-Timer Function
Basic OperationRemote Control
VOLUME
buttons
P-TIMER
button
MUTE
button 
						

							24
Choose Computer by pressing the INPUT button on the top
control or press the COMPUTER button on the remote control.
Before using these buttons, a correct input source should be
selected through Menu Operation as described below.
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the Input Menu icon.1
Computer 
Input Menu
Press the Point d button to move the red arrow pointer to
Computer and then press the SELECT button.  2
After the Source Select Menu appears for Computer,  move
the pointer to RGB and then press the SELECT button.3
Top Control
Input Source Selection
Direct Operation
Menu Operation
Computer Input 
Move the pointer (red
arrow) to Computer
and press the SELECT
button. Input Menu icon
Move the pointer to RGB and
press the SELECT button.
Source Select Menu
COMPUTER
button
Remote Control
POWERLAMP
REPLACE WARNING
INPUT
MENU ON - OFF
SELECTVOLUME–VOLUME+
INPUT
button
Computer 
Video 
						

							25
Computer Input
The Auto PC Adjustment
function operates to adjust
the projector. 
PC System Menu
The PC System Menu icon 
displays the system being
selected.
Systems on this dialog box can
be selected.Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the PC System Menu icon.
Press the Point d button to move the red arrow pointer to
the desired system and then press the 
SELECT button.  
1
2
PC System Menu
Custom Mode (1~5) set in the
PC Adjust Menu. (p27, 28)
PC system can also be selected manually.
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional settings. (The signal formats provided in this projector is
shown on page 55.)
The projector cannot recognize the connected signal
conforming to the provided PC Systems. The
message Auto is displayed on the PC System Menu
icon and the Auto PC Adjustment function works to
display proper images. If the image is not projected
properly, a manual adjustment is required. (p27, 28)
There is no signal input from computer. Check the
connection between your computer and the projector.
(See  Troubleshooting on page 50.)
Auto
-----
The preset system is manually adjusted in the PC
Adjust Menu. The adjusted data can be stored in
Mode 1
~5. (p27, 28)  
Mode 1
PC Systems provided in this projector is chosen. The
projector chooses a proper system provided in the
projector and displays it.  SVGA 1
Selecting Computer System Manually
*Mode 1 and SVGA 1 are examples.  
Computer Input
One of the following messages may appear when: 
						

							26
Computer Input
The Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical positions
to conform to your computer. Auto PC Adjustment function can be operated as follows.
Move the red frame pointer to
the Auto PC adj. icon and
press the SELECT button. 
Please wait ... message
appears while Auto PC
Adjustment is in progress.
PC Adjust Menu
PC Adjust Menu icon
To store the adjusted parameters
The system parameters adjusted in the Auto PC Adjustment can
be stored in the projector. Once the parameters are stored, the
setting can be done just by selecting Mode in the PC System
Menu (p25). See “Store” on page 28.
✔Note:
• Fine sync, Total dots and Picture Position of some computers can not be fully
adjusted with the Auto PC Adjustment function. When the image is not provided
properly, manual adjustments are required (p27, 28).
• The Auto PC Adjustment cannot be operated when 480i, 575i, 480p, 575p,
720p,1035i, or 1080i is selected in the PC System Menu (p25).
Auto PC Adjustment
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to PC Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to
Auto PC adj. icon and then press the SELECT button twice. Auto PC adj.
Direct Operation
The Auto PC Adjustment function can be operated directly by
pressing the AUTO PC button on the remote control.
Remote Control
AUTO PC
button
Menu Operation 
						

							27
Computer Input
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the PC Adjust Menu icon.1
Move the red frame pointer to
an item and press the SELECT
button.
PC Adjust MenuPC Adjust Menu icon
Eliminate a flicker from the image displayed. Press the Point 7 8
buttons to adjust the value. (From 0 to 31.)
Adjust the number of total dots in one horizontal period. Press the
Point 
7 8buttons to adjust the number to match your PC image. Total dots
Press the Point 7 8buttons to adjust the horizontal picture
position.Horizontal
Press the Point 7 8buttons to adjust the vertical picture position. Vertical
Press the SELECT button to show H-sync freq. and V-sync freq. of
the connected computer. Current mode
Adjust the clamp level. When the image has dark bars, try this
adjustment.Clamp
Press the SELECT button at
this icon to adjust other items. 
Press the Point 7 8buttons to
adjust the value.Status of the
selected Mode
(Stored/Free) Selected Mode
Press the SELECT button at
the Current mode icon to
show the information of the
connected computer.
Current mode
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC
Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5
independent memory areas to store those parameters manually adjusted, which allows you to recall the setting for a
specific computer. 
Computer Input
2Press the Point dbutton to move the red frame pointer to
the desired item and then press the SELECT button. The
adjustment dialog box will appear. Press the Point 
7 8
buttons to adjust the value.
Fine sync 
						

							28
Computer Input
Press the SELECT button to display the Display area dialog box
and select the resolution.Display area
Adjust the horizontal area displayed by the projector. Press the
Point 
7 8buttons to decrease/increase the value and then press
the SELECT button.Display area H
Adjust the vertical area displayed by the projector. Press the Point
7 8buttons to decrease/increase the value and then press the
SELECT button.Display area V
With this function on, SXGA image is fully displayed at 4 : 3 aspect
ratio. It is displayed at 5 : 4 aspect ratio with this function off.  Full screen
Reset
Store
Exit the PC Adjust Menu.
Quit
To store adjusted data, move the red frame pointer to the Store
icon and then press the SELECT button. Move the red arrow
pointer to any of Mode 1 to 5 in which you want to store and then
press the SELECT button.
To reset the adjusted data, select Reset and press the SELECT
button. The confirmation box will appear and then select [Yes]. All
adjustments return to their previous figures.
Mode free
Vacant Values of “Total dots”,
“Horizontal”, “Vertical”,
“Display area H”, and
“Display area V”.Close this dialog box.
To clear adjusted data
To store adjusted data
To clear the adjusted data previously set, move the red frame
pointer to the Mode free icon and then press the SELECT button.
Move the red arrow pointer to the Mode that you want to clear
and then press the SELECT button.  Display area
Press the SELECT button at
the Display area icon to display
the Display area dialog box.
This Mode has the parameters being stored.
✔Note:
• Auto PC Adjustment, Display area, Display area (H/V), and Full screen cannot be
selected when 480i, 575i, 480p, 575p, 720p, 1035i, or 1080i is selected in the PC
System Menu (p25).
The confirmation box
will appear and then
select [Yes].
The confirmation box
will appear and then
select [Yes]. 
						

							29
Computer Input
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the Image Select Menu icon.1
2Press the Point dbutton to move the red frame pointer to
the desired level and then press the SELECT button.
Move the red frame pointer to
the desired image level and
press the SELECT button.
The image level being selected.
Image Select Menu
Normal picture level preset on this projector.Standard
Picture level with improved halftone for graphics.Real
Picture level suitable for the image projected on a blackboard.
See above for further details.Blackboard(Green)
Image Select Menu icon
Select an image level among Dynamic, Standard, Real,
Blackboard(Green), Image 1, Image 2, Image 3, and Image 4 by
pressing the IMAGE button on the remote control.
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Normal picture level preset on this projector.  
Picture level with improved halftone for graphics. Standard
Real
Image 1~4
Image Level Selection 
Direct Operation
Menu Operation
Image 4
User preset image in the Image Adjust Menu (p30).Image 1~4
Blackboard(Green)
Picture level suitable for the image projected on a blackboard. This
mode helps to enhance the image contrast projected on the
blackboard. This is mainly effective on a green colored board, not
truly effective on a black colored board.
Blackboard(Green)
Picture level suitable for viewing a picture in a bright room.Dynamic
Picture level suitable for viewing a picture in a bright room. Dynamic
User preset image in the Image Adjust Menu (p30).
Standard
Computer Input
IMAGE button
Remote Control  
						

							30
Computer Input
Press the Point 7 8 buttons to
adjust the value.
Press the MENU button to display the On-Screen Menu.
Press the Point 
7 8buttons to move the red frame pointer
to the Image Adjust Menu icon.1
2Press the Point dbutton to move the red frame pointer to
the desired item and then press the SELECT button. The
level of each item is displayed. Adjust each level by pressing
the Point 
7 8buttons.Move the red frame pointer to
an item and then press the
SELECT button.
Image Adjust Menu
Press the Point 7 button to decrease the contrast and the Point 8
button to increase the contrast. (From 0 to 63.)
Press the Point 7 button to adjust the image darker and the Point
8button to adjust the image brighter. (From 0 to 63.)Contrast
Brightness
Press the Point 7 8buttons to obtain a better balance of contrast.
(From 0 to 15.)Gamma
Image Adjust Menu icon
Press the Point 7button to lighten red tone and the Point 8
button to deepen red tone. (From 0 to 63.)White balance (Red)
Press the Point 7button to lighten green tone and the Point 8
button to deepen green tone. (From 0 to 63.)White balance (Green)
Press the Point 7button to lighten blue tone and the Point 8
button to deepen blue tone. (From 0 to 63.)White balance (Blue)
Selected Image level
Press the Point 7 8buttons to select the desired Color temp.
level. (XLow, Low, Mid, or High) Color temp.
Image Level Adjustment
To reset the adjusted data, select Reset and press the SELECT
button. The confirmation box will appear and then select [Yes]. All
adjustments return to their previous figures.
Reset
Store
Exit the Image Adjust Menu.
Quit
To store the adjusted data, select Store and press the SELECT
button. The confirmation box will appear and then select [Yes].
Stored data can be called up by selecting Image in the Image
Level Selection on page 29. If you change the Image level (p29)
without storing the adjusted data, the figures will go back to the
factory default settings.
✔Note:
• After adjusting the White balance of Red, Green or Blue, the Color temp. level
will change to Adj..
The confirmation
box will appear and
then select [Yes].
Image Level Menu
Move the red frame pointer to
a desired image level among
Image 1 to 4 and then press
the SELECT button. Store icon
Press the SELECT button at
this icon to store the adjusted
data.