Eiki Projector EK-502X User Manual

							11
Compliance
The AC Power Cord supplied with this projector meets the requirement for use\
 in the country you purchased it.  
AC Power Cord for the United States and Canada:AC Power Cord used in the United States and Canada is listed by the Unde\
rwriters Laboratories (UL) 
and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit 
into the power outlet. Do not try to defeat this safety feature. Should \
you be unable to insert the plug into 
the outlet, contact your electrician.
AC Power Cord Requirement
AC Power Cord for the United Kingdom:This cord is already fitted with a moulded plug incorporating a fuse, th\
e value of which is indicated on the 
pin face of the plug.  Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be 
used of the same rating, marked thus 
ASA. If the fuse cover is detachable, never use the plug with the 
cover omitted. If a replacement fuse cover is required, ensure it is of \
the same colour as that visible on 
the pin face of the plug (i.e. red or orange). Fuse covers are availab\
le from the Parts Department 
indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should b\
e cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct\
 plug fitted. 
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE 
SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the followi\
ng code:
 Green-and-yellow  ....... . Earth
 Blue .................     Neutral
 Brown ...............     Live
As the colours of the wires in the mains lead of this apparatus may not \
correspond with the coloured 
markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the ter\
minal in the plug which is 
marked by the letter E or by the safety earth symbol 
 or coloured green or green-and-yellow.
The wire which is coloured blue must be connected  to the terminal which is marked with the letter N or 
coloured black.
The wire which is coloured brown must be connected to the terminal which\
 is marked with the letter L or 
coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE. FCC Caution
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class A limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwi\
se specified in the 
instructions. If such changes or modifications should be made, you could be required to stop operation of 
the equipment.
Model Number : EK-502X, EK-501W
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)  
						

							12
Accessories
Owner's Manual(CD)AC Power cordRemote control with batteries
(AA or LR6)
VGA cable Quick start guide Lens Cover
US Type x1
Euro Type x1  
						

							Overview
This chapter presents names and 
functions of individual component. 
						

							14
Name and function of your projector
Front/top
 Projection lens
 Air intake with filter
 POWER indicator (Refer to Page 69)
– The power indicator turns steady red when your projector is in standby m\
ode 
–  It turns steady green when your projector is in normal operation 
  STATUS indicator (Refer to Page 69)
It flashes red when internal temperature of your projector is out of operation range
 FILTER indicator (Refer to Page 69)
It turns red when the filter needs be replaced 
 Lens release button
12
3
4
5
6  
						

							15
Name and function of your projector
Rear
 ON/STAND-BYPower on or off your projector 
 Arrow  
–  Select items or adjust values in the 
OSD menu.
–  Select display area in digital zoom+ 
mode 
–  Adjust the volume.
 ZOOM/FOCUS 
– Enter the optical zoom adjustment 
mode
–  Enter the focus adjustment mode 
 BLANK 
Dark out screen images temporarily 
 MENU Open or close the OSD menu 
 LENS SHIFT 
Enter the lens moving mode 
 ENTER 
Enter the OSD menu or select options in 
a menu 
 INPUT Select source of input 
 Air exhaust
 Adjustment pad
Note:
Air outlet emits hot air. DO NOT place 
heat sensitive objects near it. 
1
3
4
5
6
10
9
7
8
360.2
141.7VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
ING/Y
B/PBH/HV V
2  
						

							16
Terminal
 LAN Connect network cable to this port for con -
trolling and operating your projector via 
network. 
  VIDEO INConnect video output signal to this terminal. 
 S-VIDEO INConnect S-VIDEO output signal of video 
device to this terminal.
 VGA IN Connect output signal from computer to this 
terminal.
 MONITOR OUT Transmit signals from  to other displays 
when your projector is acting as a display 
output.
  R(PR)/G(Y)/B(PB)/H(HV)/V–  Connect RGBHV format (5-core) signals to 
R/G/B/HS/VS terminal respectively. 
–  Connect component signals to Y, Pb, Pr 
terminal respectively.
 HDMI Connect HDMI digital output signals to this 
terminal. 
 DVI-D IN(HDCP)Connect DVI digital output signals to this 
terminal. 
 AUDIO (Video)Connect audio signal from  to this terminal .
 AUDIO (S-Video) Connect audio signal from  to this terminal .
 AUDIO IN1/AUDIO IN2 –  Connect audio signals for device   
to AUDIO  IN1
–  Connect audio signals for device 
  
to AUDIO  IN2
  AUDIO OUTOutput audio signals to amplifier or other audio 
equipment. 
 SERIALConnect serial cable to this terminal when 
using RS232 device to control or operate your 
projector. 
 REMOTE INConnect wired remote controller to this  termi-
nal. Connection of a wired remote controller 
will disable the wireless one. 
  REMOTE OUTTransmit wired remote controller signals of  to another projector when a wired remote 
controller is used. 
  AUDIO/DVI-DConnect audio signals of DVI equipment to this 
terminal. 
 Anti-theft slot
 Power cord connector
VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
IN
G/Y
B/PBH/HV V
VOL- VOL+AUDIO
AUDIO
IN2
AUDIO
IN1 AUDIO
OUT
S-VIDEO
VIDEO R/C
IN R/C
OUT
RS-232C
DVI-D
P/PR
MONITOR OUT
VGA 
IN
G/Y
B/PBH/HV V
1
9
18
17
2345678
10111213141516
Name and function of your projector  
						

							17
* Laser Transmitting Window: 
  Laser beam will emit from this window while 
  pressing LASER button during the projection 
  to use the remote controller as a laser pointer.   
  
  Do not stare directly at the laser transmitting  
  window or aim the window at human body, to 
  avoid any physical injury. 
  POWERPower on or off your projector.
 LASERPress the LASER button during presentation to 
use the remote controller as laser pointer
 HDMISelect HDMI input source 
 DVISelect DVI input source 
 PATTERNSelect built-in test pattern of your projector
 VGASelect VGA input source 
 VIDEOSelect VIDEO input source 
 RGBHVSelect RGBHV input source 
 S-VIDEOSelect S-VIDEO input source 
 COMPONENTSelect Component input source 
 INPUT
Open or close the INPUT menu 
 AUTO Enter auto adjustment mode 
 Arrow  –  Select items or adjust values in the OSD 
menu
–  Select display area in digital zoom+ mode 
 OKEnter the OSD menu or select options in it 
 MENUOpen or close the OSD menu 
 VOLUME +Increase volume 
 VOLUME - 
Decrease volume
 FOCUS
Enter the focus adjustment mode
 BLANKDark out screen images temporarily 
 IMAGESelect image mode   
Remote controller
Name and function of your projector
⑨
⑩
⑪ ①
⑤ ⑦
⑥
⑧
②
*
③
④
⑬
⑭ ⑮ ⑫
⑱
⑲㉑ ㉗
㉓
㉕ ⑯
⑰
⑳ ㉒
㉖
㉙ ㉘
㉔
㉚  
						

							18
⑨⑩
⑪ ①
⑤ ⑦
⑥
⑧
②
*
③
④
⑬
⑭ ⑮ ⑫
⑱
⑲㉑ ㉗
㉓
㉕ ⑯
⑰
⑳ ㉒
㉖
㉙ ㉘
㉔
 
TIMER
Enable the timer function
 LENS SHIFTEnter the lens moving mode 
 FREEZEFreeze projected images
 KEYSTONEKeystone calibration
The keystone calibration mode changed as:
H/V Keystone -> Corner Keystone -> H/V 
Keystone -> ....
 INFO.Display current status information of your pro -
jector 
  ZOOM Enter the zooming mode 
 SCREEN Select screen size 
 D.ZOOM+Zoom in projected image 
 D.ZOOM- Zoom out projected image 
 Wired remote controller output terminalConnect cable of wired remote controller to 
this port while operating the projector by wired 
remote control
30°
30°
5m
Remote controller operation 
range
Point your remote controller to the IR receiver 
of your projector 
Maximum operation range of your remote con-
troller is an area of radius 5 meters and arc 60° 
in front of and behind your projector 
Name and function of your projector
㉚  
						

							19
 Open the battery cover.
 Insert a new battery in it.
Two AA  batteries
Place your batteries with its 
anode and cathode (+ and -) 
in correct direction. Keep both 
poles in good connection to the 
contacts within the compartment.
 Put the cover back.
Install battery of remote controller
Name and function of your projector
Please follow the following rules for safety operation: 
● Use two of AA or LR6 alkaline batteries.
● Replace both batteries at the same time.
● Do not mix new and old batteries as one pair.
● Keep your remote controller away from water or other liquids.
● Do not expose your remote controller to environments with high 
humidity or temperature.
● Do not drop your remote controller.
● In case of any battery solution leaking in the compartment, clear it 
thoroughly before placing new batteries in it. 
● Using battery of other types than what specified on this manual may 
lead to risks of explosion.
● Please dispose your old battery by following instructions given in tag 
of the battery or local regulations.  
						

							Installation
This chapter introduces the information 
of install.