Eiki Projector Eip X350 User Manual

							
EN-30
Appendix
LED Indicator Messages
The projector is operating normally.
Standby mode
During shutdown cool-down.
During flash update.
Lamp failure.
Ballast failure.
Over-temperature error.
During flash update.
Fan, sensor, or color wheel error.Projector  Condition
Lamp
-
-
-
Solid On
Blinking -
-
Indicators
Power
Solid On Blinking
Off-
-
-
-Temperature -
-
-
-
-
Solid On
Blinking 
						

							EN-31
Compatibility Modes
Computer:
CompatibilityResolutionH-Sync [KHz] V-Sync [Hz]
VGA 640x48031.469 59.940
640x48037.861 72.809
640x48037.500 75.000
640x48043.269 85.008
SVGA 800x60035.156 56.250
800x60037.879 60.317
800x60048.077 72.188
800x60046.875 75.000
800x60053.674 85.061
XGA 1024x76848.363 60.004
1024x76856.476 70.069
1024x76860.023 75.029
1024x76868.677 84.997
SXGA1280x102463.981 60.020
1280x102479.976 75.025
MAC 16”832x62449.72 74.55
MAC 19”1024x76860.241 75.020
Video:
SignalHorizontal Frequency (kHz) Vertical Frequency (Hz)
480i15.734 kHz 60 Hz
480p31.469 kHz 60 Hz
576i15.625 kHz 50 Hz576p31.25 kHz 50 Hz720p45.0 kHz 60 Hz
720p37.5 kHz 50 Hz1080i33.75 kHz 60 Hz
1080i28.125 kHz 50 Hz 
						

							
EN-32
Troubleshooting
Refer to the statement that most closely matches the nature of the probl\
em before
sending the projector for repairs. If the problem persists, contact your local reseller or
service center.
Please refer to “LED Indicator Messages” (p.30) as well.
Problem:
If no lights or sounds turn on:
If a “scanning” or “waiting”
message is displayed on a blank
screen:
If the wrong input source is
displayed:
If the image is out of focus:- Solutions
- Be sure that the power cord is securely connected
to the projector and the other end is plugged into an
outlet with power.
- Be sure the main power switch is turned on.
- Press the power button again.
- Unplug the power cord and wait for a short while, then plug it in and press the power button again.
- Press the  Source button on the projector or remote
control one or more times until the correct source
name is selected.
- Be sure the external source is turned on and connected.
- For a computer connection, ensure your notebook computer’s external video port is turned on. Refer
to the computer manual.
- Press the  Source button on the projector or the
remote control one or more times to select another
active input source.
- Be sure the lens cover is open.
- While displaying the on-screen menu, adjust the focus ring. (The image size should not change; if it
does, you are adjusting the zoom, not the focus.)
- Check the projection lens to see if it needs cleaning.
- For a computer connection, set the display
resolution as the computer to the same resolution
as the projector, 800 × 600 or 1024 × 768. If the
computer has multiple monitors, adjust the resolution
of the monitor assigned to the projector.
- For a computer connected to the S-video port, the image cannot be as high resolution as what you
see on the computer display. 
						

							EN-33
If the image is flickering or
unstable for a computer
connection:
If the remote control does not
operate:- Press the Resync button.
- Press MENU, go to Picture > VGA settings, and
adjust Frequency or Tracking.
- Be sure nothing is blocking the remote control
receiver on the front or back of the projector. Use
the remote control within the effective range.
- Aim the remote control at the screen or at the front
or back of the projector.
- Move the remote control so it is more directly in
front of or behind the projector and not as far to the
side. 
						

							U.S.A.
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA  92688-2132
 U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
 Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
China
EIKI (Shanghai) Co.,LTD
1. Dapu Road, Golden Magnolia Plaza
#2109 Shanghai,
200023 China
Tel : 86-21-5396-0088
Fax : 86-21-5396-031
E-Mail : [email protected]
Canada
EIKI CANADA -Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecka 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024 +42 02 20571413
Fax : +42 02 20571411
E-Mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
WorldWide Website  http://www.eiki.com
 03/2007 Eiki International, Inc.