Eiki Projector EIP-WX5000 EIP-WX5000L User Manual

							59
Setting the keycode
1Select “System Lock” on the “Op-
tions 1” menu, then press 
| || |
|.
•A message is displayed.
•Read this message, and press ENTER.
2Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
•When setting the keycode for the first time,
press " on the projector for four times.
Note
•If you input a wrong keycode, the cursor returns
to the first point of the “Old Code”.
•The preset keycode is 4 " buttons on the projec-
tor. If this keycode is set, the keycode input screen
does not appear when turning the power on.
3Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
Note
•You cannot use the following buttons for
keycode:
STANDBY-ON, ENTER, L-CLICK, R-CLICK/
UNDO, MENU, ZOOM, FOCUS, H&V LENS
SHIFT
•System Lock function recognizes each but-
ton on the remote control or on the projec-
tor as an individual button, even if they share
the same button name. If you set the keycode
with the buttons on the projector, use only
those buttons on the projector. If you set the
keycode with the buttons on the remote con-
trol, use only those buttons on the remote
control.
w ww w
w Setting the System Lock
Function
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only autho-
rized users have access.
 Info
•If you lose or forget your keycode, contact your
nearest EIKI Authorized Dealer or Service Cen-
ter (see page 81). Even if the product warranty
is valid, the keycode reset will incur a charge.
4Enter the same keycode in “Recon-
firm”.
Note
Not displaying the keycode input screen
when turning the projector on
•Press " on the projector for four times in steps
3 and 4 above.
When the System Lock is set
•When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to start
projection. Failure to enter the keycode will
cause images not to be projected even when
signals are entered to the projector. 
						

							60
Using the “Options 1” Menu
When the system lock is set
If you have set the system lock, enter the
keycode and follow the procedure below to
release the system lock.
    ▼Input screen for keycode
Note
•When System Lock is set, the keycode input
screen appears after the power is turned on.
•If no keycode is entered, the image will not be
displayed, even if the projector receives the in-
put signal.
1Press STANDBY-ON on the re-
mote control or  on the projector to
turn on the projector.
2When the keycode input screen ap-
pears, enter the right keycode to
start projection.
Note
•System Lock function recognizes each but-
ton on the remote control or on the projector
as an individual button, even if they share
the same button name. If you set the keycode
with the buttons on the projector, use only
those buttons on the projector. If you set the
keycode with the buttons on the remote con-
trol, use only those buttons on the remote
control.
Changing the keycode
1Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
2Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
3Enter the same keycode in “Recon-
firm”. 
						

							61
Helpful Functions Set during Installation (“Options 2” menu)
1 11 1
1 Setting a Password
• •• •
•There is no factory preset for the password,
so the “Options 2” menu is enabled.
• •• •
•If you do not want others to operate the
“Options 2” menu, set a password.
1Select “Password” from the
“Options 2” menu, and press 
| || |
|.
2Press 
' '' '
' or 
" "" "
" to set the first digit in
“New Password” and then press 
| || |
|.
3Enter the remaining 3 digits and
press ENTER.
4Enter the same password in
“Reconfirm” and press ENTER.
 Info
•The password must be entered to use the
“Options 2” menu when a password has
been set.
Changing the password
1Press 
' '' '
', 
" "" "
" and 
| || |
| to enter the pass-
word in “Old Password” and press
ENTER.
2Press 
' '' '
', 
" "" "
" and 
| || |
| to set the new
password in “New Password” and
press ENTER.
3Enter the same 4-digit password in
“Reconfirm” and press ENTER.
Note
•If you do not want to set a password, leave the
fields blank in steps 2 and 3 and press ENTER.
•To cancel the password settings, press UNDO.
If You Forget Your Password
If you forget the password, delete it using the fol-
lowing procedure and set a new password.
Press 
 on the
projector.
11
2
3
4
5
6
7
8
9
0
q
w
e
t
y
u
r
Menu operation  Page 47 
						

							62
4 44 4
4 Reversing/Inverting
Projected Images
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Note
•This function is used for the reversed image and
ceiling-mount setups. (See page 23.)
5 55 5
5 Controlling Multiple
Projectors with the One
Remote Control
This function allows you to control multiple projectors
with the one remote control during the stack projec-
tion or the video wall projection. When using this func-
tion, connect the projectors with LAN cables and as-
sign a projector as the master and the other projectors
as the slaves. 
See page 27 for connecting LAN cables.
Note
•When controlling multiple projectors with the one
remote control, settings via web browser are re-
quired. Refer to the “SETUP MANUAL” contained
on the supplied CD-ROM for details.
•Only when controlling two projectors with the one
remote control, using “Pair Stack” allows you to skip
settings via web browser. (See page 63.)
•When “Slave” is selected on “Stack Setting”, the slave pro-
jector cannot be controlled with the remote control.
To control the slave projector with the remote control, con-
nect the remote control to the projector. (See page 17.)
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Selectable items
Front
Ceiling + Front
Rear
Ceiling + Rear
Helpful Functions Set during Installation (“Options 2” menu)
Description
The stack setting is not available.
Set the projector as the master.
Set the projector as the slave.
Selectable items
Normal
Master
Slave
Description
Both lamps are used for greater
brightness.
The lamp 1 is used.
When the lamp 1 burns out, the lamp 2
automatically switches in use.
The lamp 2 is used.
When the lamp 2 burns out, the lamp 1
automatically switches in use.
Both lamps are used alternately for
certain periods.
Selectable items
Both Lamps
Lamp 1 Only
Lamp 2 Only
Equal Use
2 22 2
2 Setting the Lamp Mode
This function allows you to select the usage of
the two lamps installed in the projector.
3 33 3
3 Selecting the Lens Type
When you change the lens, you need to set the
lens type. See the table below to select the lens
type.
Info
•The Lens Shift, Keystone Correction, etc. may not
properly function if the correct lens type is not se-
lected.
Note
•When “Lens Type” is changed, “GEOMETRIC
ADJUSTMENT”, “H&V KEYSTONE” and “IM-
AGE RESIZING” will be reset.
Attached lens
AH-55201
AH-55301
AH-55401
AH-55501
AH-55601
AH-55701
AH-55801
Selectable items
Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
Menu operation  Page 47 
						

							63
6 66 6
6 Shortcut to Make
Projector Stack Settings
Normally, settings via web browser are required for
the stack projection. You can skip the settings via
web browser by using “Pair Stack”, only when you
use the two projectors for the stack projection.
Note
•Before setting “Pair Stack”, select “Master” or
“Slave” on “Stack Setting”.
1Select “Pair Stack” on the “Option
2” menu, and then press ENTER.
•The confirmation screen will be displayed.
2Select “OK”, and then press
ENTER.
•The network settings of the projector will
change as shown below.
7 77 7
7 Locking the Operation
Buttons on the Projector
This function can be used to lock the use of cer-
tain operation buttons on the projector.
MasterSlave
IP Address 192.168.150.2 192.168.150.3
Subnet Mask 255.255.255.0 255.255.255.0
DHCP Client OFF OFF
Gateway0.0.0.0 0.0.0.0
User Name (Reset) (Reset)
Password(Reset) (Reset)
Data Port 10002 10002
Description
All operation buttons are functional.
Only INPUT/VOL buttons on the
projector are available.
All operation buttons on the projector
are unavailable.
Selectable items
Normal
Level A
Level B
8 88 8
8 Bypassing Unused Input
Selections
This function allows you to skip the input mode
that you rarely use. You can skip the input modes
when 
“Auto Search” works.
9 99 9
9 Selecting the Fan Mode
This function changes the fan rotation speed.
Note
•When “Fan Mode” is set to “High”, the fan rota-
tion speeds up, and the fan noise becomes
louder.
0 00 0
0 Setting the Auto Restart
Function
Selectable items Description
ONSets each input mode selectable
respectively.
OFFSets each input mode unavail-
able respectively.
Description
Suitable for normal environments.
Select this when using the projector at
attitudes of approximately 1,500 meters
(4,900 feet) or more.
Selectable items
 Normal
 High
COMPUTER 1
COMPUTER 2
DVI, HDMI,
VIDEO, S-VIDEO
Selectable items
On
 OffDescription
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
The projector does not turn on automati-
cally when the power cord is plugged
into the AC outlet or the breaker switch
is turned on.
Menu operation  Page 47 
						

							64
q qq q
q Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Note
•Refer to the “SETUP MANUAL” contained on
the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.
•Refer to the computer’s owner’s manual for in-
structions for setting the computer’s baud rate.
w ww w
w Setting the Monitor
Output
When the Monitor Out has been set to “Enable”,
the monitor output is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the Monitor Out be set to “Disable”
when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
Description
Transmission speed is slow.
Transmission speed is rapid.Selectable items
9600 bps
38400 bps
115200 bps
Description
The monitor output function is activated
even if the projector is in standby mode.
The monitor output function is switched off
when the projector is in standby mode.
Selectable items
Enable
Disable
e ee e
e Setting the LAN/RS232C
When the LAN/RS232C has been set to “Enable”,
the LAN/RS232C is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the LAN/RS232C be set to “Disable”
when it is not connected.
 This reduces power
consumption when the projector is in the standby
mode.
Note
•When you want to control the projector using
the LAN/RS232C function, select “Enable.”
•The item “LAN/RS232C” will be made unavail-
able for setting when “Master” or “Slave” is se-
lected on “Stack Setting”. (“LAN/RS232C” will
be set to “Enable” automatically.) (See page 62.)
r rr r
r Setting the DHCP Client
Connect the LAN cable before turning the pro-
jector on. If not, the DHCP Client function does
not work.
Note
•Select “ON” for “DHCP Client”. “Obtaining IP
Address...” appears, then the message “The
network settings have been changed.”, IP Address,
Subnet Mask and Gateway will be displayed.
•If the DHCP server is not available, “Could not
obtain IP Address.” appears.
In this case, set the TCP/IP manually. (See “Set-
ting the TCP/IP” on page 65.)
Description
The LAN/RS232C function is activated
even if the projector is in standby mode.
The LAN/RS232C function is switched off
when the projector is in standby mode.
Selectable items
Enable
Disable
Description
Obtains configuration parameters for
TCP/IP network automatically.
Sets the TCP/IP manually.
Selectable items
ON
OFF
Helpful Functions Set during Installation (“Options 2” menu)
Menu operation  Page 47 
						

							65
Note
•Before setting “TCP/IP”, select “OFF” for “DHCP
Client”.
•Confirm the existing network’s segment (IP ad-
dress group) to avoid setting an IP address that
duplicates the IP addresses of other network
equipment or computers. If “192.168.150.002”
is not used in a network with an IP address of
“192.168.150.XXX”, you don’t have to change
the projector IP address.
•For details about each setting, consult your net-
work administrator.
t tt t
t Setting the TCP/IP
Set the TCP/IP manually.
1Select “TCP/IP”, then press ENTER.
2Enter “IP Address” using 
' '' '
', 
" "" "
", 
| || |
|
and \, then press ENTER.
3Enter “Subnet Mask” using 
' '' '
', 
" "" "
",
| || |
| and \, then press ENTER.
4Enter “Gateway” using 
' '' '
', 
" "" "
", 
| || |
| and
\, then press ENTER.
Description
Factory default setting:
192.168.150.002
Enter an IP address appropriate for the
network.
Factory default setting:
255.255.255.000
Set the subnet mask to the same as that
of the computer and equipment on the
network.
Factory default setting:
000. 000. 000. 000
* When not in use, set to:
  “000. 000. 000. 000”.
Selectable items
IP Address
Subnet Mask
Gateway
y yy y
y Service Mode
Only the service centers use the menu. Do not
use the menu.
u uu u
u Returning to the Default
Settings
This function allows you to initialize the settings
you have made in the projector.
Note
About the network settings
•“IP Address”, “Subnet Mask”, “Gateway”  and
other network setting items are initialized.
The following items or menu cannot be initialized.
•“C. M. S.” menu
-“Lightness”, “Chroma” and “Hue” respectively
saved for Custom 1-3 on the “C.M.S.” menu.
•“Fine Sync” menu
-Resolution
•“Options 1” menu
-System Lock
•“Options 2” menu
-Lens Type
•“Language” menu
•Image stored using “Image Capture”
•Lamp Timer (Life)
Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 16 languages.
Overview of All Menu
Settings and the Lamp Life
This function can be used to display all the ad-
justed settings as a list on the screen and you
can confirm the lamp life.
Helpful Functions Set during Installation (“Options 2”
menu)/Using the Other Menus (“Language” and
“Status” menus)
Menu operation  Page 47 
						

							66
Cleaning the air vents and the intake vent cover
■Use a vacuum cleaner to clean dust from the ex-
haust vent, the intake vents and the intake vent cover
(on the bottom of the projector).
Cleaning the projector
■Ensure the power cord is unplugged before clean-
ing the projector.
■The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■Do not use volatile agents such as insecticides on
the projector.
Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic may
cause damage to the quality or finish of the projector.
■Wipe off dirt gently with a soft flannel cloth.
■When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
Cleaning the lens
■Use a commercially available blower or lens clean-
ing paper (for glasses and camera lenses) for clean-
ing the lens. Do not use any liquid type cleaning
agents, as they may wear off the coating film on the
surface of the lens.
■As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.
Maintenance
Mild detergent
diluted with water
WaxThinner
Mild detergent
Cleaning
Paper
Info
•If you want to clean the air vents and the intake
vent cover during projector operation, ensure
you press STANDBY-ON on the projector or on
the remote control and put the projector into
standby mode. After the cooling fan has stopped,
unplug the power cord from the AC socket and
clean the air vents and the intake vent cover. 
						

							67
Cleaning the Dust Filters
1Press STANDBY-ON  on the pro-
jector or on the remote control
to put the projector into standby
mode.
• Disconnect the power cord and unplug
the power cord from the AC socket after
the cooling fan stops.
2Remove the filter cover.
•Remove the filter cover as shown in
the figures while pressing down the
tabs.
3Clean the dust off the dust fil-
ters and the cover with a hand
broom.
Cleaning and Replacing the Dust Filters
•The dust filters should be cleaned every 100
hours of use. Clean the filters more often
when the projector is used in a dusty or
smoky location.
Info
Po wer cord
STANDBY-ON button 
						

							68
Cleaning and Replacing the Dust Filters
4Replace the filter cover.
•Insert the filter cover as shown in the
figure and push both the two tabs until
you hear a click.
Remove
Attach
Pierced through 
the nine slits.
Insert the filter 
below the six tabs 
on both left and 
right sides.
Note
• Be sure the filter cover is securely installed.
The power will not turn on unless it is cor-
rectly installed.
Replacing the Dust Filters
After removing the filter cover (see
step 2 of “Cleaning the Dust Filters”),
remove the dust filters, then replace
with new ones.
•Pick the dust filters up with your fingers and lift
them out of the filter cover.
• When attaching the dust filters, make sure that
these are inserted below the tabs on both left
and right, and that the slits are pierced through.
•If the filters become too dirty to clean effec-
tively, purchase new ones (9NK3243101400)
from your nearest EIKI Authorized Dealer or
Service Center.
Info
1
2