Eiki Projector EIP-WX5000 EIP-WX5000L User Manual

							19
Quick Start
Page 21
1.Place the projector facing a screen
Pages 24, 28
Page 28
Press  STANDBY-ON  on the projector or on the remote control.
This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3.Remove the lens cap and turn the projector on
When connecting equipment other than the computer,
see pages 
25 and  26.
5
4
6
76
7
6
4 3
8
4
6
7
4
38
5
6 
						

							20
Pages 29, 30
4.Adjust the angle
5.Adjust the focus and the zoom
Page 31
8.Turn the power off
Page 28
7.Select the input mode
Page 36
1
1 1
1
1 Press  FOCUS +/–  on the projector or on the remote control to adjust the focus.
2
2 2
2
2 Press  ZOOM +/–  on the projector or on the remote control to adjust the zoom.
Press INPUT  on the projector or  COMPUTER1 on the remote control to select the “COMPUTER1” mode.
•
• •
•
• When you press  INPUT on the projector, the INPUT list appears.
Press ' /"  to switch the INPUT mode and then press  ENTER.
•
• •
•
•When using the remote control, press  COMPUTER1/2, DVI , HDMI , VIDEO  or  S-VIDEO  to switch the input mode.
Press  STANDBY-ON  on the projector or on the remote control. While the confirmation message is displayed,
press  STANDBY-ON  a gain.
•
• •
•
• You can unplug the power cord even if the projector is operating.
•
• •
•
• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
Adjust the projector angle:
•
• •
•
•
Shift the lens horizontally and vertically.
1
1 1
1
1Press  H&V LENS SHIFT  on the projector or
on the remote control.
2
2 2
2
2Press ' , " , \  or  | on the projector or the
remote control.
•
• •
•
•Adjust the projector angle by rotating the adjust-
ment feet.
6.Correcting the image distortion due to the projection angle
1
1 1
1
1 Press  KEYSTONE  on the projector or on the remote control.
2
2 2
2
2 Press  ENTER  on the projector or on the remote control.
3
3 3
3
3 Press  ', " , \  or  |  to move the position for the upper left of the image.
4
4 4
4
4 Press  ENTER  to set the position.
5
5 5
5
5
Repeat the same procedure with the positions for the upper right, lower right and lower left of the image.
•
• •
•
•When the position of the lower left is set, the correction is made and the display disappears.
Page 32
"
" "
"
"  On-screen display
On the
projector On the remote
controlINPUT listOn-screen display (RGB)
Quick Start 
						

							21
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
•For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■Place the projector at the required distance from the screen according to the desired picture size. (For
details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.)
Setting Up the Projector
Rightmost lens shift
position Leftmost lens shift 
position
Lens centerLens center Screen
WCenter of screen
Top View
Indication of the Projection Image Size and Projection Distance
For details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.
Example : NORMAL Mode (16:10) for the standard zoom lens (AH-55501)
280
200
100
80
60 Picture Size
170×106
85×5368×4251×32
Projection Distance
36–451
(11.0 m – 13.7 m)259–323
(7.8 m – 9.8 m)1210–161
(3.9 m – 4.9 m)103–1211
(3.1 m 
– 3.9 m)79–98
(2.4 m – 2.9 m)
237×148
Upper lens shift 
position
(Desktop setup) Lower lens shift 
position
(High mount setup)
H1
H2Screen
Side View
Lens center Lens center
Center of screen
L 
						

							22
Standard Zoom Lens (AH-55501 : Standard Equipment with EIP-WX5000)
F2.5, f=25.5-32 mm
16:10 Signal Input (Normal Mode)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0392χ
L2 (m) = 0.0491χ
H1 (cm) = –1.56815χ
H2 (cm) = 0.2221χ
W (cm) = ±0.75379χ
[Feet/inches]
L1 (ft) = 0.0392χ
 / 0.3048
L2 (ft) = 0.0491χ
 / 0.3048
H1 (in) = –1.56815χ
 / 2.54
H2 (in) = 0.2221χ
 / 2.54
W (in) = ±0.75379χ
 / 2.54 χ
:Picture size (diag.) (in/cm)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H1: Lower distance from the lens center to the bottom of the image (cm/in)
H2: Upper distance from the lens center to the bottom of the image (cm/in)
W: Distance from the lens center to the center of the image (cm/in)
Note
•Allow a margin of error in the value in the diagrams above.
•When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
•See page 21 about projection distance [L] and distance from the lens center to the bottom of the image [H].
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.04438χ
L2 (m) = 0.05559χ
H1 (cm) = –1.77527χ
H2 (cm) = 0.25143χ
W (cm) = ±0.85344χ
[Feet/inches]
L1 (ft) = 0.04438χ
 / 0.3048
L2 (ft) = 0.05559χ
 / 0.3048
H1 (in) = –1.77527χ
 / 2.54
H2 (in) = 0.25143χ
 / 2.54
W (in) = ±0.85344χ
 / 2.54 χ
:Picture size (diag.) (in/cm)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H1: Lower distance from the lens center to the bottom of the image (cm/in)
H2: Upper distance from the lens center to the bottom of the image (cm/in)
W: Distance from the lens center to the center of the image (cm/in)
4:3 Signal Input (Normal Mode)
Setting Up the Projector
Picture (Screen) size Projection distance [L]Distance from the lens center to
the bottom of the image [H]Distance from the lens
center to the center of
the image [W]
Diag. [χ
]
Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
280
250
200
150
120
100
80
60(711 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(152 cm)603 cm
538 cm
431 cm
323 cm
258 cm
215 cm
172 cm
129 cm(237)
(212)
(170)
(127)
(102)
(85)
(68)
(51)377 cm
337 cm
269 cm
202 cm
162 cm
135 cm
108 cm
81 cm(148)
(132)
(106)
(79)
(64)
(53)
(42)
(32)
11.0 m
9.8 m
7.8 m
5.9 m
4.7 m
3.9 m
3.1 m
2.4 m(36 0)
(32 2)
(25 9)
(19 3)
(15 5)
(12 10)
(10 3)
(7 9)–439.1 cm (–172 55/64)
–392.0 cm (–154 
11/32)
–313.6 cm (–123 
15/32)
–235.2 cm (–92 
39/64)
–188.2 cm (–74 
5/64)
–156.8 cm (–61 
47/64)
–125.5 cm (–49 
25/64)
  –94.1 cm (–37 
3/64)
62.2 cm (24 31/64)
55.5 cm (21 
55/64)
44.4 cm (17 
31/64)
33.3 cm (13 
7/64)
26.7 cm (10 
1/2)
22.2 cm (8 
3/4)
17.8 cm (7)
13.3 cm (5 
1/4)±211.1 cm (83 
3/32)
±188.4 cm (74 
3/16)
±150.8 cm (59 
23/64)
±113.1 cm (44 
33/64)
±90.5 cm (35 
39/64)
±75.4 cm (29 
43/64)
±60.3 cm (23 
47/64)
±45.2 cm (17 
13/16) 13.7 m (45 1)
12.3 m (40 3)
9.8 m (32 3)
7.4 m (24 2)
5.9 m (19 4)
4.9 m (16 1)
3.9 m (12 11)
2.9 m (9 8)
Picture (Screen) size Projection distance [L]Distance from the lens center to
the bottom of the image [H]Distance from the lens
center to the center of
the image [W]
Diag. [χ
]
Width Height Minimum [L1] Maximum [L2] Lower [H1] Upper [H2]
240 (610 cm)
200 (508 cm)
150 (381 cm)
120 (305 cm)
100 (254 cm)
80 (203 cm)
70 (178 cm)
60 (152 cm)488 cm (192)
406 cm (160)
305 cm (120)
244 cm (96)
203 cm (80)
163 cm (64)
142 cm (56)
122 cm (48)366 cm (144)
305 cm (120)
229 cm (90)
183 cm (72)
152 cm (60)
122 cm (48)
107 cm (42)
91 cm (36)
10.7 m (34 11)
8.9 m (29 1)
6.7 m (21 10)
5.3 m (17 6)
4.4 m (14 7)
3.6 m (11 8)
3.1 m (10 2)
2.7 m (8 9)–426.1 cm (–167 47/64)
–355.1 cm (–139 
25/32)
–266.3 cm (–104 
27/32)
–213.0 cm (–83 
7/8)
–177.5 cm (–69 
57/64)
–142.0 cm (–55 
29/32)
–124.3 cm (–48 
59/64)
–106.5 cm (–41 
15/16)
60.3 cm (23 3/4)
50.3 cm (19 
51/64)
37.7 cm (14 
27/32)
30.2 cm (11 
7/8)
25.1 cm (9 
29/32)
20.1 cm (7 
59/64)
17.6 cm (6 
59/64)
15.1 cm (5 
15/16)±204.8 cm (80 
41/64)
±170.7 cm (67 
13/64)
±128.0 cm (50 
13/32)
±102.4 cm (40 
5/16)
  ±85.3 cm (33 
19/32)
  ±68.3 cm (26 
7/8)
  ±59.7 cm (23 
33/64)
  ±51.2 cm (20 
5/32)
13.3 m (43 9)
11.1 m (36 6)
8.3 m (27 4)
6.7 m (21 11)
5.6 m (18 3)
4.4 m (14 7)
3.9 m (12 9)
3.3 m (10 11) 
						

							23
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■Reverse the image by selecting “Rear” in the “PRJ Mode” menu. (See page 62.)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■When the translucent screen is placed between the mirror and audience, select “Front” in the “PRJ Mode”
menu. (See page 62.)
■When the mirror is placed on the audience side, select “Rear” in the “PRJ Mode” menu. (See page 62.)
Info
•When using a mirror, ensure that both the projector and the mirror are carefully placed so the projected
light does not shine into the eyes of the audience.
Ceiling-mount Setup
■It is recommended that you use the optional EIKI ceiling-mount
adaptor and unit for this installation.
Before mounting the projector, contact your nearest EIKI Autho-
rized Dealer or Service Center to obtain the recommended ceil-
ing-mount adaptor and unit (sold separately).
■Invert the image by selecting “Ceiling + Front” in “PRJ Mode”.
See page 62 for use of this function.
Translucent screen
Audience
Set to “Front”
AudienceTranslucent screenMirrorSet to “Rear”
Audience
Mirror 
						

							24
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off
the equipment to be connected. After making all connections, turn on the projector and then the other
pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after
all the connections are made.
IMPORTANT: Ensure that the appropriate input mode has been selected on the projector before you
turn on the connected equipment.
•F or more details of connection and cables, refer to the o wner’s manual of the connected equipment.
•You may need other cables or connectors not listed below.
COMPUTER/COMPONENT1
DVI-D
DVI Digital cable (commercially available)RGB cable (supplied)
Mini D-sub 15 pin/5 BNC cable (commercially available)
Computer audio cable (ø3.5 mm stereo minijack, 
commercially available)
RGB output terminal
RGB output terminal
Computer audio output 
terminal
DVI digital output terminal
Computer audio cable (ø3.5 mm stereo minijack, 
commercially available)Computer audio output 
terminal
Computer audio cable (ø3.5 mm stereo minijack, 
commercially available)Computer audio output
terminal
HDMI cable (commercially available) HDMIHDMI digital output terminal
Equipment CableTerminal on connected equipmentTerminal on the projector
Computer
COMPUTER/COMPONENT2
T erminals on the Projector
Note
• When connecting the projector to a compatible computer other than a PC (\
VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more
information.
• When connecting to the DVI-D or HDMI terminal, select “D. PC RGB” for “Signal Type” in the “Picture”
menu.
• See page  75 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the func\
tions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computer\
s. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on.  Refer to the specific instructions in your computers owner’s manual
to enable your computer’s external output port. 
						

							25
Note
•Select the input signal type of the video equipment when connecting to the COMPUTER1/2, DVI-D or
HDMI terminal. See page 51.
•The HD/C sync and VD terminals may be used depending on the specifications of the DTV decoder
connected to this projector. Please refer to the owner’s manual of the DTV decoder for details.
•The HD/C sync terminal of the 5 BNC terminal is only for TTL signal.
•Select “480P” or “576P” for “Resolution” on the “Fine Sync” menu, if necessary. (See page 53.)
•While the projector is connected to video equipment that has an HDMI output terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
•Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment that
has HDMI digital output terminal using HDMI to DVI digital cable.)
•For details on compatibility for connection, see support information on DVI connection provided by the
video equipment manufacturer.
•When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
•The projector does not support RGBC signals via the Euro-scart.
ø3.5 mm stereo minijack to RCA audio cable (commercially 
available)
Cables for a camera or a video game/3 RCA to 
mini D-sub 15 pin cable (commercially available)
ø3.5 mm stereo minijack to RCA audio cable (commercially 
available)
Component video 
output terminal
RCA adaptor plug 
(commercially available)
COMPUTER/COMPONENT2
COMPUTER/COMPONENT2
COMPUTER/COMPONENT1
HDMI
DVI-D
5 BNC cable (commercially available) 
Component cable (commercially available) + BNC-
RCA adaptor plug  (commercially available)RGB video output terminal
Audio output terminal
Audio output terminal
Audio output terminal
D-video 
output terminal
Audio output terminal Video equipment, 
Camera, Video game
DVI digital output terminal
HDMI digital output terminal
ø3.5 mm stereo minijack to RCA audio cable (commercially 
available)
DVI Digital cable (commercially available) HDMI cable (commercially available)
ø3.5 mm stereo minijack to RCA audio cable (commercially 
available)
Equipment CableTerminal on connected equipmentTerminal on the projector 
						

							26
Video equipment, 
Camera, Video gameS-video cable (commercially available)S-video output terminal
Video output terminalS-VIDEO
VIDEO RCA audio cable (commercially available)
Audio output terminal
RCA audio cable (commercially available)
Audio output terminalVideo cable (commercially available)
MonitorMONITOR OUTRGB input terminalRGB cable (supplied or commercially available)
Amplifier
MONITOR OUTAudio input terminal
Equipment CableTerminal on connected equipmentTerminal on the projector
ø3.5 mm stereo minijack to RCA audio cable 
(commercially available)
Note
•When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
•Video signal for monitor output is analog RGB signal as well as component signal (COMPUTER1/2). DVI
and HDMI input video signals would not be output.
•When the audio from HDMI input is directed to the MONITOR OUT (AUDIO) terminal, output will be
generated as Linear PCM audio.
•HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
•Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.
•The HDMI terminal does not support the CEC signal.
Connecting the Projector to Other Equipment
This projector is able to process the following signals when connected to HDMI
equipment:
•Video signal: For details, see “HDMI Support” in the list of  “Computer Compatibility Chart” on page 75.
•Audio signal: Linear PCM audio
•Sampling frequency: 48kHz/44.1kHz/32kHz 
						

							27
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to the RS-232C serial terminal on
the computer, or when the LAN terminal on the projector is connected to the LAN terminal on
the computer, the computer can be used to control the projector. Refer to the “SETUP MANUAL”
contained on the supplied CD-ROM for details.
When connecting to a computer using an RS-232C serial control cable
Note
•The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
owner’s manual of the computer for details.
•Refer to “SETUP MANUAL” contained on the supplied CD-ROM for the RS-232C specifications and
commands.
Info
•Do not connect the RS-232C cable to a terminal other than the RS-232C terminal on the computer. This
may damage your computer or projector.
•Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
When connecting to the LAN terminal using a LAN cable
Note
•When connecting to a hub, use straight-through Category 5 (CAT.5) type cable (commercially available).
•When connecting to a computer, use cross-over Category 5 (CAT.5) type cable (commercially available).
Rear view
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable 
(cross type, commercially available) Computer
Hub or computerTX/RX LED (yellow)
Illuminates when 
transmitting/receiving data. LINK LED (green)
Illuminates when linked.
To LAN terminalTo LAN terminal
LAN cable 
(Category 5 type, commercially available)
*To ensure safety, do not 
connect the LAN terminal 
with any cables such as a 
telephone line that may 
cause excessive voltage.
Rear view 
						

							28
Turning the Projector On/Off
Info
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the AC outlet or the
breaker switch is turned off when the projector is on,
then the projector automatically turns on when the power
cord is plugged into the AC outlet or the breaker switch
is turned on. (See page  63.)
• English is the factory preset language. If you want to change
the on-screen display to another language, change the lan-
guage according to the procedure on page  65.
▼On-screen display
Power cord
Supplied 
accessoryConnecting the Power Cord
Plug the supplied power cord into the
AC
 socket on the rear of the projector.
Then plug into the AC outlet.
Turning the Projector On
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages  24–27 .)
Remove the lens cap and press  STANDBY-
ON  on the projector or on the remote con-
trol.
• The power indicator illuminates red.
• After the lamp indicator illuminates, the projec-
tor is ready to start operation.
• When System Lock is set, the keycode input
screen appears. Enter the right keycode to
start projection. See page  60 for details.
Note
• The lamp indicator illuminates or blinks, in-
dicating the status of the lamp.
Green:  The lamp is on.
Blinking green: The lamp is warming up.
Red:
The lamp is shut down abnormally
or the lamp should be replaced.
•When switching on the projector, a slight flick-
ering of the image may be experienced within
the first minute after the lamp has been illumi-
nated. This is normal operation as the lamp’s
control circuitry is stabilizing the lamp output
characteristics. This does not indicate malfunc-
tion.
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to illuminate.
Turning the Power Off (Put-
ting the Projector into Standby Mode)
Press  STANDBY-ON  on the projector or
on the remote control, then press that
b utton again while the confirmation mes-
sage is displayed, to put the projector
into standby mode.
Power cord To AC outlet
To AC socket
Rear view
Lens cap
STANDBY-ON
 button
Lamp indicators1, 2Power indicator
STADNBY-ON button
Info
•
You can unplug the power cord from the AC outlet even if
the cooling fan is still running. Even if you unplug the power
cord from the projector, the cooling fan continues to run
f or a while.