Eiki Projector Eip Wss3100 User Manual

10English ...
Source1. 
ReSync2. 
HDMI3. 
Video4. 
3D5. 
Menu6. 
Four Directional Select Keys7. 
Freeze8. 
Blank9. 
Mute10. 
Power 11. 
PC12. 
Keystone 13. /
Aspect14. 
Volume +/-15. 
Remote Control
2
5
6
7
14
11
13
412
1
3
13
8
9
15
10
3VOLTSCR2025
Before using the remote control for the first time, remove the transparent insulation tape. See page 19 for   battery installation.NoteNote     

11... English
Connecting to Computer/Notebook
Installation
Due to the difference in applications for each country, some regions may have different accessories.  NoteNote
Power Cord1. 
Audio Cable 2. 
VGA to DVI-A Cable 3. 
VGA Cable4. 
RS232 Cable 5. 
LAN
Notebook
Computer
Power socket
1
22
2
4
4
HDMI Cable6. 
USB Cable 7. 
12V DC Jack 8. 
Network Cable 9. 
Monitor
Audio Output
+12V Output
345678
9  

12English ...
Connecting to Video Sources
Power Cord1. 
Microphone Cable 2. 
Audio Cable Jack/RCA 3. 
S-Video Cable 4. 
Audio Cable 5. 
VGA to HDTV (RCA) Cable 6. 
HDMI Cable 7. 
12V DC Jack 8. 
Composite Video Cable 9. 
LAN
DVD player, Set-top box, HDTV receiverS-Video output
Video output
1
6
2
+12V OutputPower socket
Audio Output
DVD player, Set-top box, HDTV receiver
5
3456
78
593
Due to the difference in applications for each country, some regions may have different accessories.  NoteNote  

13... English
Powering On the Projector
Securely connect the power cord and signal cable. When connected, the Power 1. 
LED will turn red.
Turn on the lamp by pressing 2. “  ” button on the control panel or on the remote 
control. The Power LED will turn blue.
Turn on your source that you want to display on the screen (computer, note-3. 
book, video player, etc). The projector will detect the source automatically and 
will display on the screen.
If you connected multiple sources at the same time, press...

14English ...
Powering Off the Projector
1. Press the “  ” button on the control panel or on the remote control to turn off 
the projector. The following message will be displayed on the screen.  
Press the “  ” button again to confirm.
Power Off?
Press power key again.
2. The Power LED will turn red and blink rapidly after the projector is tur\
ned off. 
And the fans will continue to operate for about 90 seconds to ensure tha\
t the 
system cools properly.
3. Once the system has finished cooling, the...

15... English
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting the image hei\
ght.
To raise the image: y
Use screw in feet to raise the image to the desired height angle and fine-tune 
the display angle. 
To lower the image: y
Use screw in feet to lower the image to the desired height angle and fine-tune 
the display angle. 
Adjusting the Projected Image
12
Elevator Feet
Elevator Feet
Elevator Feet Spacer 

16English ...
Adjusting the Projector’s Focus
Focus Ring
To focus the image, rotate the focus ring until the image is clear.
Adjusting Projection Image Size
Refer to the graphics and table show as below to determine the screen si\
ze and 
projection distance.
Adjusting the vertical image position y
Projection Distance (A)
Projection Distance (B)  Screen
WXGA Series
Screen Size (16:10)Projection Distance (A)Projection Distance (B)Projection Distance (C)
Diagonal (inch)mmInchmmInchmmInchmm
701778...

17... English
User Controls
Using the Control Panel
NameDescription
1Power LEDIndicate the projector’s status
2Power Turn the projector on/off.
3MenuLaunch the on-screen display (OSD) / Exit a menu.
4Lamp LEDIndicate the projector’s lamp status.
5Temp LEDIndicate the projector’s temperature status.
6SourceSelect an input signal.
7ResyncAutomatically synchronize the PC analog timing to its 
optimized condition.
8Four Directional 
Select Keys
Use ▲▼◄► to select items or make adjustments to 
your...

18English ...
NameDescription
1SourceSelect an input signal.
2ReSyncAutomatically synchronize the PC analog timing to its 
optimized condition.
3HDMISwitch to HDMI source.
4VideoSwitch to Composite Video or S-Video source.
53DPress the “3D” to turn the 3D OSD menu on/off.
6MenuLaunch or Exit the on-screen display(OSD).
7Four Directional 
Select Keys
Press ▲▼◄► direction buttons to select items or 
make adjustments.
8FreezePress to freeze the image. Press it again to un-freeze 
the image.
9BlankHide the...

19... English
Remote Control Battery Installation
Press firmly and slide 1. 
the battery cover off.
Put the cover 3. 
back.
Install new battery into the 2. 
compartment.
Remove the old battery and install new one (CR2025). Ensure that the side with a “+” is facing up.MnO2-LiCELL3VOLTSJAPANHCR2025
3VOLTSCR2025
M3VOLTSCR2025
To ensure safe operation, please observe the following precautions :Use CR2025 type battery.  Avoid contact with water or liquid.  Do not expose the remote control to moisture or heat....