Eiki Projector EIP-UHS100 User Manual

							31
How to Operate the On-Screen Menu
 The  projector  has  an  On-Screen  Display  (OSD)  that  allows  you  to  adjust  image  and 
change settings.
OSD Operation
Following steps are a basic way for operating the OSD.
1.   Press the MENU button to open the OSD.
2.   Press ◄ or ► to select a title menu.
3.   Press ▲ or ▼ to select an item.
  The selected item will be highlighted.
4.   Press the Enter, and ▲ or ▼ to change or adjust the selected item.
5.   Press the MENU again or press the EXIT to close the OSD .  
						

							32
Changing the OSD Language
 The product can display the menus in English, French, Spanish, German, Portuguese, 
Simplify Chinese, Traditional Chinese, Japanese, Korean, Italian, Arabic or Russian. 
  Press  MENU  to  open  the  OSD.  Go  to  CONTROL  and  select  Language  then  press  the 
Enter. You can select a language there.  
						

							33
OSD Tree
Main MenuSubmenu
INPUT Input Selection
HDMI
DVI
VGA
Component / BNC 
3G-SDI
PIP PIP Option Off/On
PIP Input HDMI
DVI
VGA
Component / BNC 
3G-SDI
PIP Swap Execute
Position Top Left
Top Right
Bottom Left
Bottom Right
Split L-R
Test Pattern Color Bar
Crosshatch
Burst
Red
Green
Blue
White
Black
Uncorrected Red
Uncorrected Green
Uncorrected Blue
H Ramp
Off
Color Space Auto
YCbCr
YPbPr
RGB-PC
RGB-Video
Input Lock Auto
48Hz
50Hz
60H
Background Logo
Blue
Black
White
Auto Sync Adjust Off
Auto
Always  
						

							34
PICTUREPicture Mode
High Bright
Presentation
Video
Contrast 0-200
Brightness 0-200
PICTURE Adaptive Contrast
On
Off
Gamma Film
Graphics
Video
Linear
Color Color Temperature 5000K
6500K
7800K
9300K
Native
Trim Red Lift
Green Lift
Blue Lift
Red Gain
Green Gain
Blue Gain
Sharpness 0-200
Noise Reduction 0-200
Aspect Ratio 5:4
4:3
16:10
16:9
1.88
2.35
Letterbox
Native
Unscaled
Overscan Off
Crop
Zoom
VGA Setup H Total 0-200
H Start 0-200
H Phase 0-200
V Start 0-200
Auto Sync Execute
LAMP Mode
Single
Dual
Power Eco
Normal
Custom Power Level
High Altitude On
Off
Custom Power Level 80.4%-100% (26 steps)
Lamp 1 Status On
Off
Lamp 1 Status On
Off  
						

							35
ALIGMENTProjection Mode
Front
Rear
Ceiling + Front
Ceiling + Rear
Fan Mode Normal
Lens Control Up
Down
ALIGMENT Lens Memory
Load Memory Memory set 1-10
Save Memory Memory set 1-10
Clear Memory Memory set 1-10
Center Lens Execute
Warp Keystone 
Rotation 
Pincushion
Barrel
Top Left Corner
Top Right Corner 
Bottom Left Corner 
Bottom Right Corner 
Reset
Blanking Top 
Bottom
Left
Right
Reset
Edge Blend Edge Blend On
Off
Blend Width To p
Bottom
Left
Right
Black Level Uplift All
Red
Green
Blue
Reset
Align Pattern On
Off
Control Eco Network Power
Standard
Eco
Auto Power Off On
Off
Auto Power On On
Off
Projector Control RS232
Network
Network IP Address
Subnet mask
Gateway
DHCP
Start Up Logo On
Off
Trigger 5:4
4:3
16:10
16:9  
						

							36
ControlTrigger
1.88
2.35
Letterbox
Native
Unscaled
Auto
Control Auto Search
On
Off
Dynamic Black On
Off
Language English 
Français 
Español  
Deutsch
Português
简体中文
繁體中文
日本語
한국어
Italiano
الإنجليزية
русский
SERVICE Model
Serial Number
Software Version
Active/PIP Source
Pixel Clock
Signal Format
H/V Refresh Rate
Lamp 1 Time
x HRS
Lamp 2 Time x HRS
Power On Time x HRS
Blue Only On
Off
Factory Reset  
						

							37
OSD Operation-INPUT
Input Selection
You can select the input source. 
HDMI
HDMI input.
DVI
DVI input.
VGA
Analog RGB.
Component / BNC
Analog / serial digital interface.
3G-SDI
Uncompressed digital video from a serial connection (coaxial)
TimingSDI Link mode Signal Standards Color EncodeSampling Structure Bit depthCable Length Tested
NTSC SD SMPTE 259M-C 270Mbps SD YCbCr4:02:02 10128m
PA L SD SMPTE 259M-C 270Mbps SD YCbCr4:02:02 10128m
1035i 60Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080i 59.94Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080i 60Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080P 30Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080P 25Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080P 50Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080P 24Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
720P 60Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
720P 50Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080Sf 25Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080Sf 30Hz HD-Single SMPTE 292M292M 1.5Gbps HD YCbCr4:02:02 10128m
1080P 50Hz 3G Level A SMPTE 424M 3Gbps YCbCr4:02:02 10128m
1080P 59.94Hz 3G Level A SMPTE 424M 3Gbps YCbCr4:02:02 10128m
1080P 60Hz 3G Level A SMPTE 424M 3Gbps YCbCr4:02:02 10128m
1080P 50Hz 3G Level B SMPTE 424M 3Gbps YCbCr4:02:02 10128m
1080P 59.94Hz 3G Level B SMPTE 424M 3Gbps YCbCr4:02:02 10128m
1080P 60Hz 3G Level B SMPTE 424M 3Gbps YCbCr4:02:02 10128m
note:
Signals are not supported for EIP-UHS100/XHS100, if it is not in the tab\
le.  
						

							38
PIP
Use this function to display multiple windows each containing an image.
PIP Option
Use this to enable or disable the Picture In Picture function.
PIP Input
Press ENTER to display available sources for the sub picture then select a source.Note 
that unavailable input source of submenu are gray out and can not be selected. The 
available input source of sub picture is as below combination list.
Source
HDMI DVIVGA Component/BNC 3G-SDI
HDMI XX O O X
DVI XX O O X
VGA OO X XO
BNC OO X XO
3G-SDI XX O O X
PIP Swap
Use the function to swap between the main screen and sub screen, below shows the 
illustration of PIP SWAP.
1221
2
1
1
2  
						

							39
Position
Use this function to select the location of the PIP window to Top left, Top Right, Bottom 
Left, Bottom Right, or Split L-R.
21
1
2
T
op Left
1
2
Bottom Left
1
2
Bottom Right Split L-R
1
2
Top Right
Test Pattern
Select  this  function  to  display  test  pattern,  press  ◄  or  ►  once  to  display  the  last  or  next 
pattern, press EXIT to exit test pattern.
Color Space
This  function  allows  you  to  change  component  and  RGB  input  sources.  You  can  select 
different color space for different color performance. 
  Auto:   The default setting is Auto.
 HDMI:  If the Auxiliary Video Information (AVI) contains color space and/or range data,  
      the EIP-UHS100/XHS100 uses that information to switch to corresponding c\
olor  
     space. 
 RGB:   If Hsync or Vsync signals are present, the projector will switch to RGB-PC color  
     space. 
 Component:  For SDTV and EDTV resolutions, the EIP-UHS100/XHS100 uses the    
             REC601 color space. For all other resolutions REC709 is used.
In most cases, the Auto setting determines the correct color space. If it does not, you can 
use a specific color space. Choose one of the following:
 YCbCr:  uses component color space and sets black at 0,0,0 and white at 255,255,\
255.
 YPbPr:  uses composite color space and sets black at 0,0,0 and white at 255,255,\
255.
 RGB-PC:  uses RGB color space and sets black at 0,0,0 RGB and white at 255,255,255   
            RGB, assuming an 8-bit image.
 RGB-Video:  uses RGB color space and sets black at 16,16,16 RGB and white at    
            235,235,235, assuming an 8-bit image, to correspond to the luminance   
            values defined in digital component standards.
Input Lock
Use  this  function  to  lock  a  source  to  an  internal  sync  signal  (Auto,  48Hz,  50Hz,  or  60Hz). 
Auto setting locks the sync signal to the current source.
Background
Use  this  function  to  set  the  background  screen  with  no  signal.  You  can  select  from  Logo, 
Blue, Black and White. The default setting is Logo.
Auto Sync Adjust
Use the function to adjust the setting automatically for the incoming signal by the black 
level, gain, and reference (Always, Off, Auto).  
						

							40
OSD Introduction – PICTURE
Picture Mode
Use ◄ or ►to select the High Bright, Presentation and Video mode.
Contrast
Use ◄ or ► to adjust the contrast of the projected image.
Note:
Brightness and Contrast controls are interactive. The screen change to o\
ne may require a subtle change to 
the other in order to achieve the optimum setting
Brightness
Use  ◄  or  ►to  adjust  the  level  of  black  in  the  image  to  increase  or  decrease  image 
brightness.
Adaptive Contrast
Use ◄ or ►to adjust the light and dark aspects of the contrast curve.
Gamma
Use ◄ or ► to selerct Video, Film or Graphics.
Color
Use ◄ or ► to adjust the color temperature of the projected image.
This refers to the control of color imbalance in the darker areas of the projected image. It is 
recommended that you use an external test image with many areas of dark \
and gray colors 
(i.e. an image of 30IRE-window). If you notice minimal amount of red, green or blue in the 
gray areas, adjust the offset of the corresponding color accordingly. This function will shift 
the entire color spectrum for the whole image and change its brightness.\