Eiki Projector EIP-UHS100 User Manual

							11
Projection Size v.s Distance
EIP-UHS100
Fixed
Short Throw
AH-CD20201
Inch WideTele FixedW ideTeleWideTeleWide Tele Wide TeleWide Tele
40 861
x5380 .620.790 .641 .051.521.451.931.873.153 .014 .604.427.05
80 1723x1077 1.29 1.63 1.32 2.163.092.973.923.826.39 6.16 9.339.1314.40
100 2154x1346 1.62 2.05 1.66 2.713.883.734.924.808.00 7.74 11.7011.4818.07
120 2584x1615 1.96 2.46 2.01 3.264.664.495.915.779.62 9.31 14.0613.8421.75
150 3231x2019 2.46 3.09 2.52 4.095.845.637.417.2412.04 11.68 17.6117.3727.26
200 4307x2692 3.29 4.14 3.37 5.477.817.539.909.6816.08 15.61 23.5223.2636.44
250 5384x3365 4.13 5.18 4.23 6.859.779.4312.39 12.1220.12 19.55 29.4429.1545.62
300 6461x4038 4.96 6.23 5.08 8.2311.7311.3414.8814.5624.16 23.49 35.3535.0454.81
350 7538x4711 5.80 7.27 5.94 9.6113.7013.2417.3717.0028.20 27.42 41.2740.9363.99
400 8615x5384 6.63 8.32 6.79 10.9915.6615.1419.8619.4432.24 31.36 47.1846.8273.18
450 9692
x6057 7.47 9.36 7.65 12.3717.6217.0422.3621.8836.28 35.30 53.1052.7182.36
500 10768  x 67308.3010.41 8.50 13.7519.5918.9424.8524.3240.32 39.24 59.0158.6091.54
Long Throw
Long Throw
AH-CD20203 AH-CD20301AH-CD20302
W x H (mm) AH-CD20202
AH-CD20101AH-CD20401Long Thro
w
d
r
a
d
n
a
t
S
w
o
r
h
T
 
t
r
o
h
S
e
p
y
T
 
s
n
e
LS hort Throw
Model Name
EIP-XHS100
Fixed
Short Throw
AH-CD20201
Inch WideTele FixedW ideTeleWideTeleWide Tele Wide TeleWide Tele
40 813
x801626x100 2032x1202438x1503048x2004064x2505080x3006096x3507112x4008128x4509144
500x
W x H (mm) Long Throw
Long Throw Long Throw
Model Name AH-CD20203A H-CD20202AH-CD20101 AH-CD20401 AH-CD20301 AH-CD20302
Lens Type
Short ThrowS hort ThrowStandard 610  0.61  0.77  0.62  1.03 1.49 1.42 1.88 1.83 3.08  2.94  4.49 4.31 6.89
1219  1.26  1.59  1.29  2.11 3.02 2.90 3.83 3.73 6.24  6.02  6.12 8.91 14.07
1524  1.58  2.00  1.62  2.65 3.79 3.65 4.80 4.69 7.82  7.56  11.43 11.22 17.66
1829  1.91  2.40  1.96  3.18 4.56 4.39 5.78 5.64 9.40  9.10  13.74 13.52 21.25
2286  2.40  3.02  2.46  3.99 5.71 5.50 7.24 7.07 11.77  11.41  17.21 16.97 26.64
3048  3.21  4.04  3.29  5.34 7.63 7.36 9.67 9.46 15.72  15.25  22.99 22.73 35.62
3810  4.03  5.06  4.13  6.69 9.55 9.22 12.11  11.84 19.67  19.10  28.78 28.48 44.59
4572  4.84  6.08  4.96  8.04 11.47 11.07 14.54 14.23 23.62  22.95  34.56 34.24 53.57
5334  5.66  7.10  5.80  3.39 13.39 12.93 16.98 16.61 27.57  26.80  40.34 39.99 62.55
6096  6.47  8.12  6.63  10.74  15.31 14.79 19.41 19.00 31.52  30.64  46.12 45.75 71.53
6858  7.29  9.14  7.47  12.09  17.23 16.64 21.85 21.38 35.47  34.49  51.90 51.50 80.50
7620  8.10  10.16  8.30  13.44  19.14 18.50 24.28 23.77 39.42  38.34  57.69 57.26 89.48
x
10160
Distance unit : m
Note:
The values in the tables are approximate and may be slightly different f\
rom the actual measurements.  
						

							12
Overview
Projector contents
Part Names and Functions
SH UTTER
T
EM P.
L
A M P 2
L
AM P 1
P
O W ER
S TA TU S
1
10
2
3
9
46785
Rear side
1112
13141516
① Color Wheel Cover
② Infrared Remote Receiver(Front)
③ Lens Release Button
④ Air Intake Vent and Filter Cover
⑤ Adjustable Foot
⑥ AC Power Switch
⑦ Power Cord Connector
⑧ Terminals and Connectors
⑨ Control Panel
⑩ LED Indication
⑪ Exhaust Vent
⑫ Infrared Remote Receiver(Rear)
⑬ Exhaust Vent and Lamp 1 Cover
⑭ Exhaust Vent and Lamp 2 Cover
⑮ Air Intake Vent and Filter Cover
⑯ Adjustable Foot  
						

							13
Terminals and Connectors
INOUT
TEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-D B/PbG/YR/Pr
WIRED REMOT ETRIGGER
SDI
Input SDI signals to IN and outputs the SDI signals from OUT.
HDMI
Connect the HDMI signal from the video device to this terminal.
DVI-D
Connect  the  DVI-D  output  on  the  computer  to  the  terminal,  the  terminal  can  support  to 
HDCP compatible signal.
5 BNC INPUT JACKS
Connect the RGB signals or YPbPr singals.
WIRED REMOTE  
Connect the wired remote control to this jack with a remote control cable (supplied).
TRIGGER
The TRIGGER terminal provides 12V (+/-1.5) output for screen control.
LAN
Connect the Ethernet cable to the terminals for controlling the projector . (page 62)
RGB
Connect a computer output (Analog D-sub 15-pin type) to this terminal.
RS-232
Connect  a  RS-232(Not  supplied)  from  the  computer  to  the  terminal  for  controlling  the 
projector.  
						

							14
Control Keys and Indicators
Control Keys
SHUTTER
POWER
MENU EXIT
INPUTAUTO SYNC ASPECTOPEN
FOCUS
LENS
SHIFT
CL OSE
ZOOMENTE R
++
--
POWER
Turn on/off the projector.
INPUT  
Select the input source, press the button once to select next source opt\
ion, the sequence 
of the source is HDMI, DVI, VGA, Component/BNC, Composite, 3G-SDI.
AUTO SYNC
Use the button to perform auto sync.
ASPECT
Change aspect ratio, press the button once to the next aspect ratio setting.
SHUTTER OPEN/CLOSE
Press OPEN button to open the shutter, CLOSE to close the shutter. 
MENU
Press the button to open or close the OSD menu.
ARROW BUTTONS
Use the four button to move the cursor on OSD, select the item or adjust the setting.
ENTER
Use the button to confirm the changes you made and to show ZOOM/FOCUS OSD. When 
you press the button again, LENS SHIFT OSD appears.
EXIT
Use the button to close the OSD menu.
LENS SHIFT
Press the four arrow buttons to open Lens control window.
FOCUS +/-
Use FOCUS+ or FOCUS- to focus the projected image.
ZOOM +/-
Use the two buttons to zoom in or zoom out the projected image.  
						

							15
LED Indicator
SHUTTER
TEMP.
LAMP 
2
LAMP 
1
POWER
ST ATUS
This  indicator  flashes  green  when  the  projector  is  warming  up  and 
keep green when turning on.
Indicates the status of the projector.
The indicator lights green when the lamp 1 is on, the indicator is off 
when the lamp is off.
Indicate the system temperature status. The indicator is
flashing red if abnormal temperature is detected.
This indicator lights green when the shutter is closed, it lights
off when the shutter is open. The indicator lights green when the lamp 2 is on, the indicator is off 
when the lamp is off.  
						

							16
Remote Control
3
8
10
13
16
21
1
4
11
19
14
22
17
2
5
6
9
12
15
18
20
23
7
1 ON
 Turn the projector on.
2. OFF
  Turn the projector off.
3. FOCUS
  Focuses the projected images.
4. ZOOM
  Zoom in/out the projected image.
5.  TEST PATTERN
  Display test pattern.
6.  LENS SHIFT
  Shift the lens, up/down or left/right.
7. ENTER
  Confirm the change. Open ZOOM/FOCUS OSD. 
  Press again to open LENS SHIFT.
8. MENU
  Open and close the OSD menu. 
9. EXIT
  Close the OSD menu.
10. INPUT
  Select a input source.
11. PICTURE
  Starts the PICTURE function.
12. NETWORK
  Enter the Network (LAN) menu.
13. AUTO  SYNC
  Automatically adjust the computer image to its      
  optimum setting.
14. ASPECT
  Select the aspect ratio settings.
15. PIP
  Display the picture-in-picture screen.
16. OVERSCAN
  Select an overscan mode.
17. FREEZE
  Freeze/unfreezes the on-screen picture.
18. LAMP  MODE
  Select a higher or lower brightness setting.
19. INFO.
  Display projector information.
20. LIGHT
  Turn on the remote control backlight.
21. CLEAR
  Not available
22. SHUTTER
  Open/close the shutter.
23. ID  SET
  Not available  
						

							17
Notes on Remote Control Operation
	 In	most	situations,	 you	can	simply	 point	the	remote	 control	at	the	 screen	 which	will	reflect	 the	IR	signal	
from	 the	remote	 back	toward	 the	IR	receiver	 on	the	 projector. 	In	 some	 cases, 	however, 	ambient 	light 	may 	
prevent this. If so, try again.
If the effective range of the remote control decreases, or it stops working, replace the batteries with new 
ones.
  The remote control may fail to operate if the infrared remote sensor is \
exposed to bright sunlight or 
fluorescent	lighting.
Remote Control Battery Installation
    
1.  Slide the battery cover to remove it.
2.  Install two AA(2) batteries with the correct polarity.
3.  Put back the cover.
Notes on Batteries
Make sure that the battery polarities are correct when installing the ba\
tteries.
Do not mix an old battery with a new one or different types of batteries\
.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If you will not use the remote control for periods long time, remove the\
 batteries to avoid damage from battery 
leakage. Please wipe the remote control clean and install new batteries \
if the battery is leaked.
Dispose of used batteries according to the instructions or your local di\
sposal rule or guideline.
Remote Control Receivers and Operation Range
 Infrared Remote Receivers are provided on the front and rear cover. Point the remote 
control toward the projector, than press the buttons. Maximum operating range for the 
remote control is about 10 meters and ±30 degrees.
S H UTTER
T
EM P.
L
AM P 2
L
AM P 1
P
O W ER
S TA TU S
10m
±30°
 
10m
±30°
Note:
When	hanging	 the	projector	 from	the	ceiling,	 point	toward	 the	Infrared	 Remote	 Receiver	 which	is	located 	
farther	away	from	the	fluorescent	light.	  
						

							18
Wired Remote Control
 The remote control can be used as a wired remote control. Wired remote c\
ontrol helps 
you  use  the  remote  control  outside  the  operating  range.  Connect  the  remote  control  and 
the projector with the remote control cable (supplied). If the remote control is connected to 
the cable, the remote control does not emit signal.
IN OUT
TEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER  
						

							19
Installation
Lens Installation
 
Before setting up the projector, install Projection Lens on the projector.
Before installation, check where the projector is used and prepare a suitable lens. For the 
details,  contact the sales dealer where you purchased the projector.
To install and change the projector Lens:
1. Remove the Lens cap.

2. Insert the lens and ensure the lens touches the lens holder. Align the "" symbol on 
the lens label with the "
" symbol on the top of the body (align to the center of the lens 
hole).Make  sure  the  lens  is  pushed  into  the  holder  and  turn  it  clockwise  to  the  "Lock" 
position.  When  turning  the  lens,  the  "Click"  sounds  once  to  indicate  that  the  lens  is 
completely fixed.
Align symbol  
						

							20
Lens replacement
To replace the projector Lens
1. Press and hold the lens lock button. Support the lens and turn countercl\
ockwise to    
  loosen the lens. Pull the lens backward and slide the lens out of the le\
ns holder.
2. Insert the lens and ensure the lens touches the lens holder. Align the "" symbol on 
  the lens label with the "
" symbol on the top of the body (align to the center of the lens  
 hole).
Align symbol
3.  Make sure the lens is pushed into the holder and turn it clockwise to the "Lock" position.  
  When turning the lens, the "Click" sounds once to indicate that the lens is completely  
  fixed.
4.  Check if the lens is really secured by trying to pull the lens out of the lens holder .
Note:
When removing the lens, make sure you press and hold the release button \
to loosen and unlock the lens
The projector supports the lens memory function. Perform the Center Lens\
 function every time to calibrate 
the projection lens after you installed the lens.