Eiki Projector EIP-UHS100 User Manual

11
Projection Size v.s Distance
EIP-UHS100
Fixed
Short Throw
AH-CD20201
Inch WideTele FixedW ideTeleWideTeleWide Tele Wide TeleWide Tele
40 861
x5380 .620.790 .641 .051.521.451.931.873.153 .014 .604.427.05
80 1723x1077 1.29 1.63 1.32 2.163.092.973.923.826.39 6.16 9.339.1314.40
100 2154x1346 1.62 2.05 1.66 2.713.883.734.924.808.00 7.74 11.7011.4818.07
120 2584x1615 1.96 2.46 2.01 3.264.664.495.915.779.62 9.31 14.0613.8421.75
150 3231x2019 2.46 3.09 2.52 4.095.845.637.417.2412.04 11.68 17.6117.3727.26
200...

12
Overview
Projector contents
Part Names and Functions
SH UTTER
T
EM P.
L
A M P 2
L
AM P 1
P
O W ER
S TA TU S
1
10
2
3
9
46785
Rear side
1112
13141516
① Color Wheel Cover
② Infrared Remote Receiver(Front)
③ Lens Release Button
④ Air Intake Vent and Filter Cover
⑤ Adjustable Foot
⑥ AC Power Switch
⑦ Power Cord Connector
⑧ Terminals and Connectors
⑨ Control Panel
⑩ LED Indication
⑪ Exhaust Vent
⑫ Infrared Remote Receiver(Rear)
⑬ Exhaust Vent and Lamp 1 Cover
⑭ Exhaust Vent and Lamp 2 Cover
⑮ Air Intake...

13
Terminals and Connectors
INOUT
TEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-D B/PbG/YR/Pr
WIRED REMOT ETRIGGER
SDI
Input SDI signals to IN and outputs the SDI signals from OUT.
HDMI
Connect the HDMI signal from the video device to this terminal.
DVI-D
Connect  the  DVI-D  output  on  the  computer  to  the  terminal,  the  terminal  can  support  to 
HDCP compatible signal.
5 BNC INPUT JACKS
Connect the RGB signals or YPbPr singals.
WIRED REMOTE  
Connect the wired remote control to this jack with a remote...

14
Control Keys and Indicators
Control Keys
SHUTTER
POWER
MENU EXIT
INPUTAUTO SYNC ASPECTOPEN
FOCUS
LENS
SHIFT
CL OSE
ZOOMENTE R
++
--
POWER
Turn on/off the projector.
INPUT  
Select the input source, press the button once to select next source opt\
ion, the sequence 
of the source is HDMI, DVI, VGA, Component/BNC, Composite, 3G-SDI.
AUTO SYNC
Use the button to perform auto sync.
ASPECT
Change aspect ratio, press the button once to the next aspect ratio setting.
SHUTTER OPEN/CLOSE
Press OPEN button to...

15
LED Indicator
SHUTTER
TEMP.
LAMP 
2
LAMP 
1
POWER
ST ATUS
This  indicator  flashes  green  when  the  projector  is  warming  up  and 
keep green when turning on.
Indicates the status of the projector.
The indicator lights green when the lamp 1 is on, the indicator is off 
when the lamp is off.
Indicate the system temperature status. The indicator is
flashing red if abnormal temperature is detected.
This indicator lights green when the shutter is closed, it lights
off when the shutter is open. The...

16
Remote Control
3
8
10
13
16
21
1
4
11
19
14
22
17
2
5
6
9
12
15
18
20
23
7
1 ON
 Turn the projector on.
2. OFF
  Turn the projector off.
3. FOCUS
  Focuses the projected images.
4. ZOOM
  Zoom in/out the projected image.
5.  TEST PATTERN
  Display test pattern.
6.  LENS SHIFT
  Shift the lens, up/down or left/right.
7. ENTER
  Confirm the change. Open ZOOM/FOCUS OSD. 
  Press again to open LENS SHIFT.
8. MENU
  Open and close the OSD menu. 
9. EXIT
  Close the OSD menu.
10. INPUT
  Select a input...

17
Notes on Remote Control Operation
	 In	most	situations,	 you	can	simply	 point	the	remote	 control	at	the	 screen	 which	will	reflect	 the	IR	signal	
from	 the	remote	 back	toward	 the	IR	receiver	 on	the	 projector. 	In	 some	 cases, 	however, 	ambient 	light 	may 	
prevent this. If so, try again.
If the effective range of the remote control decreases, or it stops working, replace the batteries with new 
ones.
  The remote control may fail to operate if the infrared remote sensor is \
exposed to...

18
Wired Remote Control
 The remote control can be used as a wired remote control. Wired remote c\
ontrol helps 
you  use  the  remote  control  outside  the  operating  range.  Connect  the  remote  control  and 
the projector with the remote control cable (supplied). If the remote control is connected to 
the cable, the remote control does not emit signal.
IN OUT
TEJ
H
V
RG
B
LAN
RS-232
HDMI
DVI-DB /PbG /YR/Pr
WIRED REMO TETRIGGER  

19
Installation
Lens Installation
 
Before setting up the projector, install Projection Lens on the projector.
Before installation, check where the projector is used and prepare a suitable lens. For the 
details,  contact the sales dealer where you purchased the projector.
To install and change the projector Lens:
1. Remove the Lens cap.

2. Insert the lens and ensure the lens touches the lens holder. Align the "" symbol on 
the lens label with the "
" symbol on the top of the body (align...

20
Lens replacement
To replace the projector Lens
1. Press and hold the lens lock button. Support the lens and turn countercl\
ockwise to    
  loosen the lens. Pull the lens backward and slide the lens out of the le\
ns holder.
2. Insert the lens and ensure the lens touches the lens holder. Align the "" symbol on 
  the lens label with the "
" symbol on the top of the body (align to the center of the lens  
 hole).
Align symbol
3.  Make sure the lens is pushed into the holder and turn it...