Eiki Projector Eip Sxg20 User Manual

21
Installation
Connecting to Video Equipment
Video Source (example)Video Cassette Recorder DVD Player
RGB SCART 
21-pin Output
YPb/Cb Pr/Cr
Y-Pb/Cb-Pr/Cr
Component video output equipment.  
(such as DVD player or 
high-definition TV source.)
Component Video Output 
BNC
Cable  DVI 
Cable 
SCART-VGA
Cable 
DIGITAL
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
S-Video 
Output
S-VIDEO
Cables used for connection 
• Video Cable...

22
Installation
Attaching the Cable Cover
Fix the opposite end of the strap to the hole inside the 
support cover with a screw (supplied).
1
3
Insert the support cover into the cover insertion slot and 
slide it to the left.
4
Tie a strap (supplied) to the lower bracket on the right side 
of the projector’s terminal area. (See the right figure.)
2
Dress and secure all cables to a cable tie (supplied). The 
cable tie is reusable and can be opened and closed as 
many times as needed.
Tie another strap...

23
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector sideAC Outlet side
To POWER CORD 
CONNECTOR on your 
projector. Ground
To the AC Outlet.
(120 V AC)
For Continental EuropeFor the U
 .S .A .  and CanadaFor the U  .K .
To the AC Outlet.
(200–240 V AC) To the AC...

24
Turning On the Projector
Connect the projector’s AC power cord into an AC 
outlet and turn on the MAIN ON/OFF Switch. The 
LAMP indicator lights red and the POWER indicator 
lights green.
Press the ON/STAND-BY button on the side control 
or on the remote control. The LAMP indicator 
dims red and the cooling fans start to operate. The 
preparation display appears on the screen and the 
countdown starts. 2
3 1
The preparation display will disappear after 20 
seconds.
4After the countdown, the input...

25
Press the ON/STAND-BY button on the side control 
or on the remote control, and “Power off?” appears 
on the screen.
Press the ON/STAND-BY button on the side control 
or on the remote control again to turn off the 
projector. The LAMP indicator lights bright and the 
POWER indicator turns off. After the projector is 
turned off, the cooling fans operate. You cannot turn 
on the projector during this cooling down period.1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU 
TURN THE PROJECTOR ON, WAIT AT...

26
Side Control
SELECT button
How to Operate the On-Screen Menu
MENU button
SELECT button
POINT buttons
On-Screen Menu
The projector can be adjusted or set via the On-Screen 
Menu. For each adjustment and setting procedure, refer 
to the respective sections in this manual.
Use the Point 
7 8 buttons to select a Menu icon. 
Use the Point 
ed buttons to select an item in the 
selected menu.
Press the SELECT button to show the item data. 
Use the Point 
7 8 buttons to adjust the values.
To close the...

27
Menu Bar
For Computer Source
For Video Source
Show the selected Menu of the On-Screen Menu.
Used to select computer system (p.35).
Used to select an image level among Standard, Real, 
Dynamic, DICOM, and Image 1–10 (p.39).Used to adjust the size of the image. [Normal/True/Wide/
Full screen/Custom/Digital zoom +/–/Keystone/Ceiling/Rear/
Reset/] (pp.40-41).
Display the input source information (p.29). Used to adjust the computer image. [Contrast/ Brightness/
Color management/Auto picture...

28
Operating with Projector Control
Press the LENS SHIFT button and “Lens shift” will be 
displayed on the screen. Use the Point 
ed7 8 buttons 
to position the screen to the desired point without having 
picture distortion. 
The screen can be moved up or down to 55 percent, or 
sideways up to 45 percent from the central axis of the lens 
shift. Press and hold the LENS SHIFT button for more than 
5 seconds to return to the central position. See page 18 for 
details.
Lens Shift Adjustment
✔Note:
  • The...

29
Basic Operation
Information
Information display can be used to confirm the current 
operating condition of the projector and the signal being 
projected through the projector.
Press the INFORMATION button to display the 
information window on the screen. Press the Point 
d 
button or the INFORMATION button again to display the 
next page. To hide the information window, press the 
INFORMATION button again or Point 
7 8 buttons.
The information window can also be selected from the 
menu.
Information...

30
Operating with Remote Control
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons 
enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the FREEZE button on the remote control to freeze 
the picture on the screen. To cancel the FREEZE function, 
press the FREEZE button again or press any other button.
FREEZE button
Press the AUTO PC button on the remote control to 
operate the Auto PC Adj. function. The...