Eiki Lc-Xgc500 Multimedia Projector Owners Manual

50
Capture
This function enables you to capture an image being 
projected to use it for a starting-up display or interval of 
presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select [Yes] to capture the 
projected image.
After capturing the projected image, go to the Logo select 
function and set it to “User”. Then the captured image will 
be displayed the next time you turn on the projector.
To cancel the Capture function, select [No].
Select [Yes] to capture...

51
Enter a Logo PIN code
After a correct Logo PIN code 
is entered, the following dialog 
box appears.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the Point 
d button to select “Logo PIN 
code change” and then press the SELECT button. The 
New Logo PIN code input dialog box appears. Set a new 
Logo PIN code.  
Be sure to note the new Logo PIN code and keep it on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting. For...

52
Setting
This Projector is equipped with 2 Projection Lamps.  This 
function allows you to choose how to use the lamp as follows.
 Lamp1 ............ Always use Lamp 1.
  Lamp2  ........... Always use Lamp 2.
  Lamp1/2 .........  Automatically switch the active lamp from one  
lamp to the other when the projector is turned 
Off and On each time the lighting time of a 
lamp exceeds 10 hours.
Lamp control
This function allows you to change brightness of the screen.
Auto 1 .........  The brightness...

53
Setting
Pointer
You can emphasize a part of the projected image with 
this function. Use the Point 
ed buttons to choose either 
Spotlight or Pointer and press the SELECT button. Then 
use the Point 
7 8 buttons to select a size of the Spotlight 
(Large, Middle, or Small) or a pattern of the Pointer (Arrow, 
Finger, or Dot). (See page 32 for operation.)
Pointer
Remote control
Remote control
The eight different remote control codes (Code 1–Code 8) 
are assigned to the projector; the factory-set,...

54
Setting
Display
This function decides whether to display On-Screen Displays.
 On ............................  Show all the On-Screen displays. Use 
this function when you want to project 
images after the lamp becomes bright 
enough. The factory default setting is 
in this option.
  Countdown Off ........  Show the input image instead of 
the countdown when turning on the 
projector. Use this function when you 
want to project the image as early as 
possible even when the lamp is not 
bright enough....

55
Setting
Press the SELECT button at 
Power management and this 
dialog box appears. Use the 
Point 
7 8 buttons to choose 
one of the three options. 
Press the Point 
d button to 
select the timer, and then use 
the Point 
7 8 buttons to set 
timer.
Power management
Select one of the following options:
  Ready .................  When the lamp has been fully cooled 
down, the POWER indicator changes to fast 
blinking. In this condition, the projection 
lamp can be turned on if the input signal 
is...

56
Setting
Shutter
Shutter function is available to block out light to the 
screen, so that the screen can be used for the other 
presenters.Prohibits the shutter operation from the remote control 
and the projector's top control.
Remote control    ...   Selecting "On" prohibits the shutter 
operation from the remote control. 
Projector . . . . .  ...   Selecting "On" prohibits the shutter 
operation from the top control.
It is possible to prohibit the shutter operation from both of...

57
Setting
Change the PIN code lock setting
Use the Point 7 8 buttons to 
switch between the options.
Use the Point 7 8 button to select Off, On1, or On2 and 
then move the pointer to “Quit” with the Point 
d button. 
Press the SELECT button to close the dialog box.
Change the PIN code lock setting Enter a PIN code
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
  Off ...........  Unlocked.
  On1...

58
The PIN code can be changed to your desired four-digit 
number. Press the Point 
d buttons to select “PIN code 
change” and press the SELECT button. The New PIN code 
input dialog box appears. Set a new PIN code.
Change the PIN code Change the PIN code
CAUTION:
WHEN y OU HAVE CHANGED THE PIN 
CODE,  WRITE DOWN  THE NEW PIN 
CODE IN COLUMN OF  THE PIN CODE 
NO .  MEMO ON PAGE 82,  AND KEEP IT 
SECUREL y . IF y OU FORGET y OUR PIN 
CODE,  THE PROJECTOR  CAN NO LONGER 
BE STARTED .
Test pattern
Various...

59
Factory default
This function returns all setting values except for the user 
logo, PIN code lock, Logo PIN code lock, lamp counter, and 
filter counter to the factory default settings.
Exit the Setting Menu.
Quit
Select Factory default and this 
box appears. Select [Yes], and 
the next box appears. Select [Yes] to 
activate it.
Factory default
Setting
Filter counter
This function is used to set a time for the filter replacement.
Use the Point ed buttons to move the red frame pointer to Filter...