Eiki Lc-Xg400l Multimedia Projector Owners Manual

							
11
Rear	Terminal
qwe
r
t
yiu
t	USB CONNECTOR (Series B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the supplied USB cable (p.20).
y	S-VIDEO INPUT JACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
i	AUDIO  JACK
  Connect the audio output (stereo) signal from a 
computer or video equipment connected to q to 
this jack (pp.20–22).
o	AUDIO 1 JACK
  Connect the audio output (stereo) signal from a 
computer or video equipment connected to w or 
e to this jack (pp.20, 22).
r	VIDEO INPUT JACK
  Connect the composite video output signal from 
video equipment to this jack (p.21).
u	AUDIO  JACKS (L(MONO)/R)
  Connect the audio output signal from video 
equipment connected to r or  y	to these jacks 
(p.21). For a mono audio signal (a single audio jack), 
connect it to the L (MONO) jack.
q	5 BNC INPUT JACKS
  Connect the component or composite video output 
signal from video equipment to VIDEO/Y, Cb/Pb, 
and Cr/Pr jacks or connect the computer output 
signal (5 BNC Type [Green, Blue, Red, Horiz. Sync, 
and Vert. Sync.]) to G, B, R, H/V, and V jacks (pp.20–
22).
w	COMPUTER INPUT TERMINAL (ANALOG)
  Connect the computer (or RGB scart) output signal 
to this terminal (pp.20, 22).
e	COMPUTER INPUT TERMINAL (DIGITAL)
Connect  the  computer  output  signal  (Digital  DVI-D 
type)  to  this  terminal. The  HD  (HDCP  compatible) 
signal can also be connected (pp.20, 22).
o
Part Names and Functions 
						

							
1
!0	R/C JACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (supplied).
!2	MONITOR OUTPUT TERMINAL (ANALOG)
  This terminal outputs the video signal from 
computer to external video equipment (pp.20, 22).
✽	RESET button
  A  built-in  micro  processor  which  controls  this  unit 
may occasionally malfunction and need to be reset. This  can  be  done  by  pressing  the  RESET  button 
with  a  pen,  which  will  shut  down  and  restart  the unit.  Do not use the RESET function excessively.
Rear	Terminal
!0!1!2!3!4✽
!1	AUDIO MONITOR OUTPUT JACK (VARIABLE)
  This jack outputs the audio signal from computer 
or video equipment to external audio equipment 
(pp.20–22).
!3	CONTROL PORT CONNECTOR
  When controlling the projector from a computer, 
connect the computer to this connector with a 
control cable (supplied).
!4	INFRARED REMOTE RECEIVER (Back)
  The infrared remote receiver is also located in the 
front (pp.10, 16).
Part Names and Functions 
						

							
1
q
w
e
t
u
i
o
w	LAMP REPLACE indicator
  Lights yellow when the projection lamp reaches its 
end of life (pp.59, 69).
q	WARNING TEMP  . indicator
  Blinks red when the internal temperature of the 
projector exceeds the operating range (pp.61, 68).
e	ON/STAND-B y button
  Turn the projector on or off (pp.24–25).
r	INPUT button
  Select an input source (pp.34–35).
!1	INFO  . button
  Display the input source information (p.28).
y	POINT ed7 8 (VOLUME +/–) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.26).
  – Pan the image in Digital zoom + mode (p.47).
  – Adjust the volume level (Point 
7 8 buttons) 
(p.29).
u	SELECT button
  – Execute the selected item (p.26).
  – Expand or compress the image in the Digital zoom 
mode (p.47).
Top	Control
r
y
!0
!1
!2
t	LENS button
  Enter the focus, zoom, and lens shift adjustment 
mode (p.30).
i	WARNING FILTER indicator
  – Blinks orange indicating the filter needs cleaning.
  – Lights orange when clogging of the filter is 
detected, urging immediate cleaning.
o	LAMP indicator
  Lights red during operations.
!0	POWER indicator
  – Lights when in stand-by mode and during 
operations.
  – Blinks during the cooling-off period.
  – Blinks in the Power management mode (p.53).
!2	MENU button
  Open or close the On-Screen Menu (p.26).
✔Note:
	 •	All	five	indicators	on	the	top	control	blinks	when	the	
projector	detects	an	abnormal	condition.
Part Names and Functions 
						

							
14
q STAND-B y button
  Turn the projector off (p.25).
t ON button
  Turn the projector on (p.24).
y INPUT 1 –  buttons
  Select a input source (INPUT 1 – INPUT 3) (pp.34–
35).
u	AUTO PC button
  Automatically adjusts the computer image to its 
optimum setting (pp.30, 38).
i FREEZE button
  Freeze the picture on the screen (p.30).
o	POINT ed 7 8 ( VOLUME + / – ) buttons
  – Select an item or adjust the value in the On-
Screen Menu (p.26).
  – Pan the image in Digital zoom + mode (p.47).
  – Adjust the volume level (with Point 
7 8 buttons) 
(p.29).
Remote	Control
!2 L-CLICK button
  Acts as the left mouse button for wireless mouse 
operation (p.33).
e SIGNAL EMISSION indicator
  Lights red while the laser beam is being emitted 
from the laser light window or a signal is being sent 
from the remote control to the projector (p.32).
!0	PRESENTATION POINTER button
 Move a pointer of the projector or a pointer for 
wireless mouse operation (pp.32–33).
To ensure safe operation, observe the following 
precautions:
–  Do not bend, drop, or expose the remote control to 
moisture or heat.
–  For cleaning, 
use a soft dry cloth. Do not apply benzene, 
thinner, splay, or any other chemical materials.
!2
w WIRED REMOTE jack
  Connect the remote control cable (supplied) to this 
jack when using as a wired remote control.
!1 INFO  . button
  Display the input source information (p.28).r LASER LIGHT window
  A laser beam is emitted from here (p.32).
Part Names and Functions
o
t
y
r
!0
u
i
!1
qew 
						

							
15
Remote	Control
!3 MENU button
  Open or close the On-Screen Menu (p.26).
!6	ZOOM ed buttons
  Zoom in and out the images (p.30).
!5	D .ZOOM button
  Select the Digital zoom +/- mode and resize the 
image (p.47).
@0	FOCUS button
  Adjust the focus (p.30).
!8	MUTE button
  Mute the sound (p.29).
!4	P-TIMER button
  Operate the P-timer function (p.31).@1	NO SHOW button
  Temporarily turn off the image on the screen (p.31).
@2	KEy STONE button
  Correct keystone distortion (p.31).
@6	SELECT button
  – Execute the selected item (p.26).
  – Expand or compress the image in the Digital 
zoom mode (p.47).
!7	LASER button
  – Operate the Laser pointer function. Laser beam 
is emitted while pressing this button for one 
minute. When using the laser pointer for more 
than one minute, release the LASER button and 
press it again (p.32).
  – Display the Pointer on the screen (p.32).
!9 RESET/ON/ALL-OFF switch
  When using the remote control, set this switch to 
“ON.” Set it to “ALL OFF” for power saving when 
it is not in use. Slide this switch to “RESET” to 
initialize the remote control code or switch the 
Spotlight and Pointer to the Laser pointer function 
(pp.32–33).
@5	R-CLICK button
  Acts as the right mouse button for wireless mouse 
operation (p.33).
@3	LENS SHIFT button
  Select the Lens Shift function (p.30).
@4	SCREEN button
  Select the screen size (p.30).
@7	NUMBER buttons
  Act as number buttons. Use these buttons when 
setting the remote control codes (p.17) or when 
entering the PIN code numbers (pp. 24, 50–51, 
55–56).
Part Names and Functions
!9
!5
!3
!4
!8
!6
!7
@0
@6
@7
@3
@2
@1
@4
@5
For PIN code and remote control code. 
						

							
16
Projection angle can be adjusted up to 5.0 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate 
the both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button 
on the remote control or select Keystone from the menu 
(see pages 15, 31, 45).
Adjustable Feet
Adjustable	Feet
To ensure safe operation, please observe the following precautions :
	 ● Use two (2) AAA or LR03 type alkaline batteries.
	 ●  Always replace batteries in sets.
	 ●  Do not use a new battery with a used battery.
	 ●  Avoid contact with water or liquid.
	 ●  Do not expose the remote control to moisture or heat.
	 ●  Do not drop the remote control.
	 ●  If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
	 ●  Risk of an explosion if battery is replaced by an incorrect type. 
	 ●  Dispose of used batteries according to the instructions.
Press the lid 
downward and slide it.
Open the battery 
compartment lid.
Install new batteries 
into the compartment.
Replace the 
compartment lid.
Two AAA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
123
Point the remote control toward the projector (to Infrared 
Remote Receivers) when pressing the buttons. Maximum 
operating range for the remote control is about 16.4’ (5 m) 
and 60 degrees in front and rear of the projector.
Infrared Remote Receivers are provided both in front and 
back of the projector. You can conveniently use both of the 
receivers (see pages 10, 52).
Remote	Control	Receivers	and	Operating	Range
Remote	Control	Battery	Installation16.4’(5 m)
16.4’(5 m)
Part Names and Functions
✔Notes:
	 •	
	When	hanging	the	projector	from	the	ceiling,	select	the	
Infrared	Remote	Receiver	which	is	located	farther	away	
from	the	fluorescent	light	(p.52). 
						

							
17
The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 52.
Press and hold the MENU and a number button (1–8) 
for more than five seconds to switch between the 
codes.
1
To initialize the remote control code, slide the RESET/ 
ON/ALL-OFF switch to “RESET,” and then to “ON.” The 
initial code is set to Code 1.
2
Press and hold the MENU and a number button 
(1–8) that corresponds to the remote control code 
for more than five seconds to switch between 
the codes. 
MENU button
Remote	Control	Code
Number buttons
RESET/ON/ALL OFFSwitch
Part Names and Functions 
						

							
18
✔Notes:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	 ambient	lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the 
screen.
100”
32.8 (10.0m)
22.0 (6.7m)
16.4 (5.0m)
10.8 (3.3m)
3.9 (1.2m)150”
200”
300”
230”
155”
116”
78”30”
Max .  Zoom
Min . Zoom
Screen Size(W x H) mm4:3 aspect ratio
Zoom (min.)
30”
Zoom (max.)
610 x 457
3.9’ (1.2 m)
–––––
100”
2032 x 1524
14.1’ (4.3 m)
10.8’ (3.3 m)
150”
3048 x 2286
21.3’ (6.5 m)
16.4’ (5.0 m)
200”
4064 x 3048
28.5’ (8.7 m)
22.0’ (6.7 m)
300”
6096 x 4572 
–––––
32.8’ (10.0 m)
(Inch Diagonal)
(Center)
15%15%
50%
50%
uppermostdownmost
leftmostrightmost
Moving	the	Lens
For details about the Lens shift function, refer to “Lens Shift Adjustment” on page 28. The amount of lens shift 
range varies depending on the lens. The figures below are for LC-XG400.
Positioning	the	Projector	
Installation
(for LC-XG400) 
						

							
19
When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the 
sales dealer for detailed information of the optional lens specifications. 
Fit the lens to the projector by aligning the red dot 
on the lens with the red dot of the projector.
Remove the lens mount cover.1
2
Attaching the lens to the projector
Slowly turn the lens clockwise until it clicks. Make 
sure that the lens is fully inserted to the projector.3
CAUTION
Do not press the lens release button when 
attaching the lens. 
Lens	Installation
Installation
While pressing the Lens release button on the top 
of the cabinet, turn the lens counterclockwise until 
it stops and pull it out slowly from the projector.
Shift the lens to the center position by using the 
Lens shift function (see page 28).1
2
Removing the lens
CAUTION
Be careful when handling the lens. Do not 
drop.
Lens Release button
Red dot 
						

							
0
Connecting	to	a	Computer	(Digital	and	Analog	RGB)
Cables used for connection 
• VGA Cable (HDB 15 pin)* • USB Cable
• DVI-Digital Cable  • Audio Cables (Mini Plug [stereo] x 2)
• BNC Cable 
(*One cable is supplied; other cables are not supplied with the projector\
.)
External Audio Equipment
DVI-Digital 
cable
USB 
cable
Audio 
cable 
(stereo)
Audio cable 
(stereo)
USB portAudio 
Output
USB
AUDIO OUT 
(stereo)
Audio Input
Unplug the power cords of both the projector and external 
equipment from the AC outlet before connecting cables.
✔Notes:
	 •	When	the	 AUDIO	OUT	is	plugged-in,	the	projector’s	built-
in	speaker	is	not	available.
	 •	USB	cable	connection	is	needed	when	operating	the	 computer	with	the	remote	control.
Monitor 
Output
DIGITAL 
(DVI-D)
VGA 
cable
Monitor 
OutputMonitor Output
BNC 
cable
ANALOG 
IN
Monitor 
Input
VGA 
cable
ANALOG 
OUTG   B   R   H/V   VAUDIO 
IN
Installation