Eiki Lc-Xdp3500 Multimedia Projector Owners Manual

							8
Part Names
Rear
A MOUSE
Connect a USB mouse cable to a computer 
to control computer mouse functions.
B RS232
Serial data port for controlling the projector 
with  a  computer  or  other  RS-232  control 
device.
C AUDIO IN 1 & D AUDIO IN 2
Mini  jack  port  corresponds  to  computer 
input.
E AUDIO OUT
F RGB IN
Input analog RGB signal from a computer.
G RGB OUT
C o n n e c t   a n   e x t e r n a l   m o n i t o r   t o   t h i s 
connection to view the “RGB IN” input.
H DVI-I IN
Input digital DVI-I signal from a computer.
 I  S-VIDEO
S-Video signal from a video source.
 J  VIDEO
C o m p o s i t e   v i d e o   s i g n a l   f r o m   a   v i d e o 
source.
 K AUDIO IN 3, R / L
RCA type corresponds to video input.
 L COMPONENT ,Y , Pb , Pr
Input Y,Pb,Pr signal from a DVD player.
 M LAN
P l e a s e   s e e   p a g e   3 4   N e t w o r k   C o n t r o l 
Application for details.
N REAR IR RECEIVER
O SPEAKER
P  Slot  for  Kensington  Micro  Saver 
Security System
Built-in Security Slot
This security slot supports the MicroSaver® 
Security System. MicroSaver® is a registered 
trademark of Kensington Microware Inc. 
The logo is trademarked and owned by 
Kensington Microware Inc.
ABCFHIKM
OLJGED
N
P 
						

							Setting Up
9
Setting Up
When installed against a wall, leave about 20cm (7.9in.) between the p\
rojector and the wall.
8.74~10.52
5.80~7.00
4.33~5.24
2.87~3.48
2.28~2.77
1.69~2.07
1.11~1.36Distance(M)
Image size(inch)8.74~10.52
5.80~7.00
4.33~5.24
2.87~3.48
2.28~2.77
1.69~2.07
1.11~1.36
Image size(inch)
Distance(M)
Arrangement
1. 
Before installation, make sure that the projector is turned off and the power cord is disconnected.
2. Do not set up and move the projector, while it is hot.
3.   The distance between the projector and screen determines the actual image size. Refer to the table 
below to determine the screen size at a given distance.
Note: The dimensions in the table below are approximate.
Screen size (diagonal)Distance (m)Distance (feet)
inchmTeleWideTeleWide
401.01.361.114.473.62
601.52.071.696.785.54
701.82.421.987.936.51
802.02.772.289.097.47
1002.53.482.8711.409.40
1503.85.244.3317.1814.21
2005.17.005.8022.9619.03
2506.48.767.2728.7423.84
3007.610.528.7434.5228.66 
						

							10
Setting Up
Power ON / OFF
1.2.
3. 4.
Turning On The Power
1.		Make	sure	that	power	cord	is	firmly	and	
correctly connected to the projector.
2.  The POWER indicator will light up in green.
3.  Press POWER button on the control panel or 
the remote control to turn on the projector.
4. Rotate the zoom ring to adjust the screen size.
5. Rotate the focus ring to adjust the focus.
Turning Off The Power
1.  Press the POWER button on the control 
panel or the remote control. The “power off” 
confirmation	message	appears.
2.  Press the POWER button again while the 
message appears.
3.  
When the projector enters “Standby” mode, 
the POWER indicator will light up in green.
4.   If you don’t use the projector, remove power 
cord.
 WARNING
  Do not touch around the lamp cover and the 
exhaust vents during use or just after use, since it is too hot.
POWER indicator
AC inlet
Outlet
Focus ringZoom ring
Power off?Please press
key again to power off.
 WARNING
  A strong light is emitted when the projector’s 
power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.
 CAUTION
  Do not turn off the AC power for 60 seconds 
after the lamp is turned on. Doing so could cause premature lamp failure. 
						

							11
Setting Up
Setting Up The Projector
The projector supports the following four different projection methods. 
1. Front projection
2. Rear projection
3. Rear ceiling projection
4. Front ceiling projection
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details.  
						

							12
Setting Up
Ceiling Mounted Installation Guide 
Attach	ceiling	mount	at	four-suspension	bracket	fixing	points	when	suspending	from	a	ceiling.	
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details.
Security Anchor
The product is equipped with security anchor and PIN 
LOCK (See page 33 for detials) functions to help prevent 
unauthorized removal of the projector.
MAX M4x8 mm For Mounting
WARNING
►Do	not	grasp	the	security	anchor	to	carry	projector,	since	it	is	not	designed	for	it.
►	The	security	anchor	is	not	for	comprehensive	theft	prevention	measures.	It	is	intended	to	be	
used as supplemental theft prevention measure. 
						

							13
Setting Up
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image h\
eight.
1   Holding the projector, push the foot adjust 
buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the 
desired height.
3   Release the foot adjust buttons in order to 
lock the front adjustable feet.
14   Please make sure that the front adjustable 
feet are locked.
 CAUTION
*   
The adjustment range of front adjustable 
foot is 0 to 8.5 degrees.
*  
When the foot is adjusted, it may cause the 
shape of the projected image to become 
distorted. Use the keystone correction 
function  to correct this distortion. 
						

							14
Setting Up
AUDIO OUTMOUSERS-232AUDIO OUTDVI OUTVGA OUTRGB IN
AUDIO IN 
VIDEO OUT AUDIO OUT (L)&(R)
S-VIDEO OUTYPb/Cb Pr/Cr
Desktop / Lapto p
Speaker DVD Player
How To Connect
Laptop or desktop computer
Before starting, make sure that the projector and computer are both turn\
ed off.
Connect the computer cable
Connect the computer cable from the computer to the projector's RGB IN.
If needed, connect the MONITOR OUT to a monitor to view input from RGB IN.
Tighten the screw on all connectors. 
						

							15
Setting Up
How To Connect
Laptop or desktop computer
Connect the audio cable if necessary
1.  Please connect the audio cable to the AUDIO IN 1 if the computer cable is 
connected to the projector's RGB IN. 
2.   Please connect the audio cable to the AUDIO IN 2 if the computer cable is 
connected to the projector's DVI-I IN. 
3.  Please connect the audio cable to the AUDIO IN 3 if the video cables are 
connected to the VEDIO/S-VIDEO/Y,Pb,Pr port of the projector. 
Connect USB Mouse
1.  Before operating the wireless mouse, connect your computer and projector\
 with   
supplied USB cable.
2.  
When a USB cable is connected to the computer and the projector, turn on the 
projector	first,	then	the	computer.	If	you	turn	on	the	computer	first,	the	wireless	
mouse function may not operate properly.
3.  
When the projector and computer are turned on, the appropriate drivers s\
hould 
load automatically.
  If the selected video image is not displayed after the projector is turned on 
and the correct video source has been selected, please check whether the\
 
video source device is turned on and operating correctly. Also check whether 
the signal cables have been connected correctly. 
  Many laptop computers may need to change the setting for monitor output 
when connecting to the projector. Usually a key combination like Fn + F3 
or CRT/LCD key turns the external display on / off. Locate a function key 
labeled CRT/LCD or a function key with a monitor symbol on the laptop. 
Press Fn and the labeled function key simultaneously. Refer to your laptop’s 
documentation	to	find	out	your	laptop’s	key	combination.	 
						

							16
Remote Control
Remote Control Batteries 
Installation
1. Remove the battery cover. 
2. Load the batteries.
   Make sure the poles are correctly oriented.
3. Close the battery cover.
 Caution
►Avoid	excessive	heat	and	humidity.
►Do	not	drop	the	remote	control.
►	If	the	remote	control	will	not	be	used	for	an	extended	period,	remove	the	batteries.
►	Do	not	expose	the	remote	control	to	water	or	moisture.	 This	could	result	in	malfunction.
►	Replace	the	battery	when	remote	control	operation	becomes	sluggish	or	unresponsive.
►	Do	not	place	the	remote	control	close	to	the	cooling	fan	of	the	projector.
►	Do	not	use	batteries	of	different	types	at	the	same	time.
►	Do	not	mix	a	new	battery	with	used	one.	Make	sure	the	plus	and	negative	terminals	are	
correctly aligned when loading batteries.
►	Dispose	of	batteries	in	accordance	with	environmental	laws.
►	Do	not	disassemble	the	remote	control.	If	the	remote	control	needs	service,	please	contact	
your dealer. 
						

							Remote Control (Optional)
17
Remote Control
POWER
Power on / operation mode, Standby mode, Cool down mode.
INPUT
Select input source :
RGB 1       RGB 2 
S-Video
Video
DVI-I
Y,Pb,Pr
MENU
Display or hide the On-Screen Display main menu page.
 
Press  or  to select On-Screen Display menu item.
 
Press  or  to select and adjust the function of On-Screen Display menu item or value.
LASER
Aim the remote control at the screen, press and hold button to activate the laser pointer.
MUTE
Mute audio.
AUTO
Refresh the current image.
BLANK
Hide the current image, become black color on the screen.
Press / / /  button to move arrow direction of window.
MOUSE-L / MOUSE-R
The function is like mouse of desktop/ notebook.
Remote control’s mouse functions only will work if the USB cable is connected (see page 15 for instructions)