Eiki Lc-Xd25 Multimedia Projector Owners Manual

61

Follow these steps to replace the lamp.
Turn  off  the  projector  and  disconnect  the  AC  power c o r d .    A l l ow  t h e  p r o j e c t o r  t o  c o o l  fo r  a t  l e a s t  4 5 minutes.
Loosen  3  screws  of  the  lamp  with  a  screwdriver  and pull  out  the  lamp  upwards  ver tically  by  grasping  the handles.
Replace  the  lamp  with  a  new  one  and  tighten  the  3 screws  back  into  position.    Make  sure  that  the  lamp  is set  properly.    Replace  the  lamp  cover  and...

62

Maintenance and Cleaning
Be  sure  to  reset  the  Lamp  replacement  counter  after  the  lamp  is  replaced.    When  the  Lamp  replacement counter is reset, the LAMP REPLACE indicator stops lighting.
Tu r n  t h e  p r o j e c t o r  o n ,  p r e s s  t h e  M E N U  bu t t o n  t o display  the  On-Screen  Menu.    Press  the  Point  buttons  to  move  the  red  framed  pointer  to  the  Setting Menu icon.
Press  the  Point 54  buttons  to  move  the  red  framed pointer  to  the  Lamp...

6

Maintenance and CleaningAppendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make  sure  you  have  proper ly  connected  the  projector  to  per ipheral  equipment  as  descr ibed  on 
pages15-17.
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When you operate the projector with a computer and it does not project an image, restart the computer.
– Solutions Problem 
 No power –  Plug the...

64

 Image is Left/Right reversed
  Image is Top/Bottom reversed–  Check the Ceiling/Rear function. (See page 50)
–  Check the Ceiling function. (See page 50)
 No sound–  Check audio cable connections from the audio input source.
–  Adjust the audio source.
–  Press the VOLUME + button. (See page 24)
–  Press the MUTE button. (See page 24)
–  Is  the  image  projected? You  will  hear  the  sound  only  when  the 
image is projected.
 The color is strange.– Check the Input signal, color system,video...

65

Appendix
 The Remote Control does not 
work .–  Check the batteries.
–  Make  sure  there  is  no  obstr uction  between  the  projector  and 
remote control.
–  Make  sure  you  are  not  too  far  from  the  projector  when  using  the 
remote control.  Maximum operating range is 16.4' (5 m).
–  Make  sure  the  code  of  the  remote  control  is  conformed  to  that  of 
the projector. (See page 52)
–  Unlock the Key lock function for the remote control. (See page 53)
WARNING:
High voltages...

66

Appendix
Menu Tree　
System (1)Mode 1
Mode 2SVGA 1- - - -
Computer Input
✽ Systems  displayed  in  the  System  Menu  vary  depending  the  input signal.
Computer Input/Video Input
Sound
On/OffSound0 - 63
InputComputer 1 RGB Go to System (1)
QuitRGB (Scart)
ComponentGo to System (2)
Video
S-video
Go to System (3)
Go to System (3)
VolumeMuteQuit
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClamp
Display area - H
ResetMode free
0 - 31PC Adjust
Mode 3Mode 4Mode 5Quit
Yes/No
H-sync...

67

Appendix
Image AdjustContrastBrightnessColor temp.
RedGreenBlue
Gamma
Store
Quit
0 - 630 - 63High
0 - 630 - 630 - 63
0 - 15
Image 1Image 2Image 3Image 4Quit
Mid
ResetYes/No
LowXLowAdj.
Sharpness0 - 15
Digital zoom –
NormalTrueWide
Digital zoom +
Screen
Full
Dynamic
RealBlackboard (Green)
Image 1Image 2Image 3
Image Select
Image 4
Standard
CustomScaleH/V
PositionCommonResetQuit
H&VH/VYes/NoYes/No
Colorboard 
Dynamic
CinemaBlackboard (Green)
Image 1Image 2Image 3
Image Select
Image 4
Standard
Video...

68
Appendix
NormalWideScreen
Setting
Setting
Store/ResetOn/OffOn/Countdown off/Off
KeystoneBlue backDisplay
CeilingRear
Power management
On start
Capture
ReadyShut down
Hour(s)
Security
Timer (1-30 Min.)Quit
OffLogo
Factory default
L1/L2Fan
Quit
Logo select
Remote control
DefaultUser
Yes/NoLogo PIN code lock Logo PIN code entryOffOnLogo PIN code changeQuitQuit
On/OffOn/OffComputer 2/Monitor out
Off
On/OffLamp controlNormal/Auto/EcoCode 1/Code 2Key lockOffProjectorRemote ControlQuit
PIN code lock...

6
Appendix
Check the indicators for projector condition.
Indicators and Projector Condition
The projector is off. (The AC power cord is unplugged.)
The  projector  is  preparing  for  stand-by  or  the  projection  lamp  is being cooled down.  The projector cannot be turned on until cooling is completed.
T h e  t e m p e ra t u r e  i n s i d e  t h e  p r o j e c t o r  i s  a b n o r m a l l y  h i g h .  T h e p r o j e c t o r  c a n n o t  b e  t u r n e d  o n .    W h e n  t h e  p r o j e c...

70

Appendix
Compatible Computer Specifications
Basically  this  projector  can  accept  the  signal  from  all  computers  with  the V,  H-Frequency  below  mentioned and less than 140 MHz of Dot Clock.  When selecting these modes, PC adjustment can be limited.
MAC LC13640 x 48034.9766.60MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
SVGA 1800 x 60035.15656.25SVGA 2800 x 60037.8860.32SVGA 3800 x 60046.87575.00SVGA 4800 x 60053.67485.06SVGA 5800 x 60048.0872.19SVGA 6800 x...