Eiki Lc-Xb43n Multimedia Projector Owners Manual

61

Setting
Factory	default
This function returns all setting values except for the User	
logo, PIN	code	lock, Logo	PIN	code	lock,	Lamp	counter 
and Filter	counter to the factory default settings.
Factory	default
warning	log
This function records anomalous operations while the 
projector is in operation and use it when diagnosing faults. 
Up to 10 warning logs are displayed with the latest warning 
message at the top of the list, followed by previous warning 
messages in chronological order. 
Note:...

6

Input	Source	Information	Display
The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.
Lamp	counter
Information	Menu
H
KHzHz
Off
The cumulative lamp operating time is displayed.
Direct	Operation
Press the INFO. button on the remote control to display the 
Information Menu.
INFO .	button
Remote	Control
Press the Point ▲▼ buttons to select Information. The 
Information Menu is displayed. 
See below for displayed information....

63

Information
The WARNING indicator shows the state of the function which protects the projector. Check the state of the 
WARNING indicator and the POWER indicator to take proper maintenance. 
wARNING	indicator
The	projector	is	shut	down	and	the	w ARNING	
indicator	is	blinking	red .
When the temperature inside the projector reaches a 
certain level, the projector will be automatically shut down to 
protect the inside of the projector. The POWER indicator is 
blinking while the projector is being...

64

Maintenance	and	Cleaning
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filters become 
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup 
and adversely affect the life of the projector. If a Filter warning icon appears on the screen, clean the filters 
immediately. Clean the filters by following the steps below.
CAUTION
Do not operate the projector with the filters 
removed. Dust may...

65

Filter	counter	Reset? 
appears.
Select yes, then another 
confirmation box appears.
Select  yes again to reset 
the Filter counter.
Maintenance	and	Cleaning
Cleaning	the	Projector	Cabinet
Cleaning	the	Projection	Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens 
cleaner or use a lens cleaning paper or commercially 
available air blower to clean the lens. 
Avoid using an excessive amount of...

66

Maintenance	and	Cleaning
When the projection lamp of the projector reaches its end 
of life, the Lamp replacement icon appears on the screen 
and LAMP REPLACE indicator lights yellow. Replace the 
lamp with a new one promptly. The timing when the LAMP 
REPLACE indicator should light is depending on the lamp 
mode.
For continued safety, replace with a lamp of the 
same type. Do not drop a lamp or touch a glass 
bulb! The glass can shatter and may cause injury.
Allow a projector to cool for at least...

6

Maintenance	and	Cleaning
This projector uses a high-pressure lamp which must be handled carefully and properly.  
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee 
of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  life  in  a  shorter  period  of  time 
than other similar lamps.
●  If  the  projector  indicates  that  the  lamp...

68

	 Problem: – Solutions
				  – Plug the power cord of the projector into the AC outlet. 
    – See if the POWER indicator lights red. 
    –  Wait until the POWER indicator stops blinking to turn on the projector 
again. The projector can be turned on after the POWER indicator 
turns red. See page 21.
    – Check the WARNING indicator. If the WARNING indicator lights red,                 
                                                                     projector can not be turned on. See page...

69

Appendix
		 – Check the connection between your computer or video equipment  
     and the projector. See pages 17-19. 
    – See if the input signal is correctly output from your computer. Some  
     laptop computers may need to change the setting for monitor output  
       when connecting to a projector. See your computer’s instruction  
    manual for the setting.  
    – It takes about 30 seconds to display an image after turning on the  
     projector. See page 21.
    –  Check the Input...

0

Appendix
			– Check PC adjustment  or Screen and adjust them.                              
                                                                    See pages 35-36, 39-40.         
		  – PIN code lock is being set. Enter a PIN code ("1234" or numbers 
 	   you have set). See pages 22, 58-59. 
									–  Make sure your computer is connected to the projector with USB  
 					 	cable. See page 17.           
		  – Check the batteries. 
 	  – Make sure no obstruction is between...