Eiki Lc-Xb41n Multimedia Projector Owners Manual

21
Installation
Connecting to Component Video Equipment
Cables used for connection
• Audio Cables
• Scart-VGA Cable
• Component Cable
• Component-VGA Cable
(Cables are not supplied with the projector.)
External Audio Equipment
Audio cable
(stereo)
Audio cable
(stereo)
Audio Input
Component Video Output
(Y, Pb/Cb, Pr/Cr)
RGB Scart
21-pin Output Audio Output
Scart-VGA
cable Component-
VGA cable
AUDIO OUT
(stereo)
Component
cable
COMPUTER IN 2/COMPONENT IN
COMPUTER/COMPONENT AUDIO IN
✔Notes:
• When...

22
16
The preparation display will disappear 
after 30 seconds.
(See page 53 for Lamp control status.)
Lamp control status
Turning On the Projector
Basic Operation
Connect the projector’s AC power cord into an AC outlet.
The POWER indicator lights red. Open the slide shutter
by sliding the slide shutter lever (see pages 10, 64).
Press the ON/STAND-BY button on the top control or the
remote control. The POWER indicator lights green and
the cooling fans start to operate. The preparation display
appears on...

23
Basic Operation
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST FIVE MINUTES BEFORE TURNING IT OFF.
“Power off?” disappears after 4 seconds.
Turning Off the Projector
Press the ON/STAND-BY button on the top control or on
the remote control, and “Power off?” appears on the
screen.
Press the ON/STAND-BY button again to turn off the
projector. The POWER indicator starts to blink red, and
the cooling fans keep running. (You can select the level
of fans’ quietness and speed....

24
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. For each adjustment and setting procedure, refer to
the respective sections in this manual.Use the Point 
7 8buttons to select a Menu icon. Use
the Point 
edbuttons to select an item in the selected
menu.
Press the SELECT button to show the item data. Use
the Point 
7 8buttons to adjust the values.
To close the On-Screen Menu, press the MENU
button again. Press the MENU button on the top...

25
Basic Operation
Menu Bar
PC System Menu
Used to select
computer
system (p.32).
Image Adjust Menu
Used to adjust computer
image [Contrast/Brightness/
Color temp./White balance
(R/G/B)/Sharpness/Gamma]
(pp.37–38).
Setting Menu
Used to set the
projector’s operating
configurations (pp.47-
57).
Used to adjust
the volume or
mute the sound
(p.27).
Image Select Menu
Used to select an image
mode among Dynamic,
Standard, Real,
Blackboard(Green), and
Image 1–4 (p.36).
F or computer source
AV  S ystem Menu
Used...

26
Basic Operation
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control or the
AUTO SET button on the remote control, correct the image
manually as follows:
Press the KEYSTONE button on the top control or on the
remote control. The Keystone dialog box appears. Use the
Point 
edbuttons to correct keystone distortion. The
keystone adjustment can be stored (see page 48).
Auto setup function is provided to automatically correct
Keystone distortion...

27
Basic Operation
Sound Adjustment
T op Control
VOLUME+/- buttons
Remote ControlVOL – button
MUTE button
VOL + button
1
2
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Sound Menu icon.
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Press the MUTE button on the remote control to temporarily
turn off the sound. To turn the sound...

28
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisabl\
e. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the\
 On-Screen Menu.
COMPUTER/VIDEO/
NETWORK button 
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the Freeze function,
press the FREEZE button again or press any other button.
FREEZE button
Press the COMPUTER, VIDEO, or NETWORK button on...

29
Basic Operation
black out \bthe captured image  \bnormal  \b • • • • •
Press the NO SHOW button on the remote control to black
out the image. To restore to normal, press the NO SHOW
button again or press any other button. When a projected
image is captured and set as “User” in the Logo selection
(see page 49), the screen changes each time you press the
NO SHOW button as follows.
“No show” disappears after 4 seconds.
NO SHOW button
Press the P-TIMER button on the remote control. The P-Timer
display...

30
Choose either Computer 1 (Analog) or Computer 2 by
pressing the INPUT button on the top control or press the
COMPUTER button on the remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Input Menu icon.1Input Menu
Use the Point edbuttons to move the red arrow
pointer to either Computer 1 (Analog) or Computer 2,
and...