Eiki Eip-3000n Dlp Projector Owners Manual

47
Info
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only au-
thorized users have access.
• If you lose or forget your keycode, contact your
nearest EIKI Authorized Dealer or Service
Center (see page 61). Even if the product
warranty is valid, the keycode reset will incur
a charge.
Select “System Lock”, then press
hENTER or Q....

48
Note
Input screen for keycode To cancel the keycode that you have already
set
• Press R on the projector for four times in steps
2 and 3 above.
When the System Lock is set• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
Enter the same keycode in “Re-
confirm”.
• You can not use the following buttons for
keycode:
•
 oSTANDBY-ON (on the projector)
• f ON
• e STANDBY• h ENTER
• l RETURN
• B MENU/HELP...

49
Setting up the Projector Network Environment (“Network” menu)
If you do not want others to change the setting
for the “Network” menu, set a password.
Select “Password”, then press
hENTER or Q.
• The screen for entering the password
appears.
1
1 11 1
1Setting a Password
Press P or R to set the first digit
in “New Password”, then press Q.2
Enter the remaining 3 digits, then
press hENTER.
• To return to the previous digit, press O.
3
Enter the same password in “Re-
confirm”, then press hENTER.
• The...

50
Setting up the Projector Network Environment (“Network” menu)
(Continued)
Menu operation n Page 40
3 33 3
3 TCP/IP  Setting
4 44 4
4Confirming the
Projector Information
You can confirm the MAC address and projector
name.
Selectable items
IP Address
Subnet Mask
GatewayDescription
Factory default setting:
192.168.150.002
Enter an IP address appropri-
ate for the network.
Factory default setting:
255.255.255.000
Set the subnet mask to the
same as that of the computer
and equipment on the
network.
Factory...

51
Troubleshooting with the “Help” menu
Utilizing the “Help” menu func-
tions
This function advises you to solve the problems during usage.
• You can adjust the items with check marks (✔).
• The items in the “Help” menu change, de- pending on the input signal or setting that you
have selected.
• If the problem is not solved, refer to
“Troubleshooting”. (See pages  59 and  60.)
• When selecting “sRGB” in Picture Mode”, the
item “Color is faded or poor” is not displayed.
This means you cannot change input...

52
Cleaning the lens
Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.

As the surface of the lens can easily get
damaged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Cleaning the projector
Ensure that you have unplugged the...

53
Maintenance Indicators
About the lamp indicator

When the remaining lamp life becomes 5% or less,  (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to  (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.

If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
About the...

54
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plug-
ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-
nate in red and the lamp...

55
Regarding the Lamp
Lamp
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (see page 47)

Purchase a replacement lamp of type AH-66271 from your place of purchase, nearest EIKI Authorized
Dealer or Service Center.
Caution Concerning the Lamp
This projector utilizes a pressurized mercury lamp. A...

56
Regarding the Lamp (Continued)
Removing and Installing the
Lamp Unit
• Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press oSTANDBY-ON on the pro-
jector or eSTANDBY on the re-
mote control to put the projector
into standby mode.
• Wait until...