Edimax Router BR.6504N User Manual

 
90
3-1-2 Add a new QoS rule 
 
After you click ‘Add’ button in QoS menu, the following message will 
appear: 
 
 
Here are descriptions of every setup items: 
 
Rule Name (a):    Please give a name to this QoS rule (up to 15 
alphanumerical characters) 
 
Bandwidth (b):    Set the bandwidth limitation of this QoS rule. You have 
to select the data direction of this rule (Upload of 
Download), and the speed of bandwidth limitation in 
Kbps, then select the type of QoS: ‘guarantee’ 
(guaranteed usable...

 
91
input ’80-90’; if you want to apply this rule on a single 
port, just input the port number, like ‘80’. 
 
Remote IP        Specify the remote (destination) IP address 
Address: (e):    that will be affected by this rule. Please input the 
starting IP address in the left field, and input the end IP 
address in the right field to define a range of IP 
addresses, or just input the IP address in the left field to 
define a single IP address. 
 
Remote Port      Please input the range of remote...

 
92
3-2 Network Address Trnaslation  (NAT) 
 
Network address translations solve the problem if sharing a single IP address 
to multiple computers. Without NAT, all computers must be assigned with a 
valid Internet IP address to get connected to Internet, but Internet service 
providers only provide very few IP addresses to every user. Therefore it’s 
necessary to use NAT technology to share a single Internet IP address to 
multiple computers on local network, so everyone can get connected to 
Internet....

 
93
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other 
setup procedures, or click ‘Apply’ to reboot the router so the settings will 
take effect (Please wait for about 50 seconds while router is rebooting). 
 
3-2-2 Port Forwarding 
 
This function allows you to redirect a single port or consecutive ports of 
Internet IP address to the same port of the IP address on local network. The 
port number(s) of Internet IP address and private IP address (the IP address 
on local...

 
94
Here are descriptions of every setup items: 
 
Enable Port      Check this box to enable port mapping, 
Forwarding :    and uncheck this box to disable port mapping. 
 
Private IP :    Input the IP address of the computer on local network 
which provides internet service. 
 
Type :    Select the type of connection, TCP or UDP. If you’re 
not sure, please select ‘Both’. 
 
Port Range :    Input the starting port number in the left field, and 
input the ending port number in the right field. If you...

 
95
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other 
setup procedures, or click ‘Apply’ to reboot the router so the settings will 
take effect (Please wait for about 50 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, 
please click ‘Cancel’ button. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

 
96
3-2-3 Virtual Server 
 
This function allows you to redirect a port on Internet IP address (on WAN 
port) to a specified port of an IP address on local network, so you can setup 
an Internet service on the computer on local network, without exposing it on 
Internet directly. You can also build many sets of port redirection, to provide 
many different Internet services on different local computers via a single 
Internet IP address. 
 
Please click ‘NAT’ menu on the left of web management interface,...

 
97
Public Port :    Please select the port number of Internet IP address 
which will be redirected to the port number of local IP 
address defined above. 
 
Comment :    Please input any text to describe this mapping, up to 16 
alphanumerical characters. 
 
Add :        Add the mapping to virtual server table. 
 
Reset :      Remove all inputted values. 
 
Virtual Server      All existing virtual server mappings will be 
Table :    displayed here. 
 
Delete     Please select a virtual server mapping by...

 
98
take effect (Please wait for about 50 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, 
please click ‘Cancel’ button. 
 
 
 
 
 
 
3-2-4 Port Mapping for Special Applications 
 
Some applications require more than one connection a time; these 
applications won’t work with simple NAT rules. In order to make these 
applications work, you can use this function to let these applications work. 
 
 
 
 
3-2-5 UPnP Setting 
 
This...

 
99
 
 
There is only one option in this page, please select ‘Enable’ or ‘Disable’ to 
enable or disable UPnP function, then click ‘Apply’ button, and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other 
setup procedures, or click ‘Apply’ to reboot the router so the settings will 
take effect (Please wait for about 50 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to...