Edimax Router AR-7265WnA User Manual

 3
1.2. Minimum Requirements 
The following devices are necessary to configure and use the ADSL2+ Router： 
• A PC with Pre-installed Ethernet Adapter (Required) and a Web-Browser 
(Internet Explorer 4.0 or higher) 
• RJ-45 Ethernet crossover cable (Included in the package) 
• RJ-11 (ADSL Ready) phone Line 
 
 
1.3. Package Content 
• One ADSL2/2+ Router (Annex A or B) 
• 3dBi Antennas x 3 
• One 12V Power Adapter  
• One RJ-45 Ethernet Cable (100 cm) 
• One RJ-11 Telephone Line (180 cm) 
• One Quick...

 4
1.4. Hardware Placement 
1.4.1. Rear Panel 
 
 
 
1) Antenna Connectors 
The antenna connector of the router is reverse SMA connector. It allows you 
to connecting an external antenna with reverse SMA connector to the router 
easily.  
 
2) Reset 
     The Reset button can be used to reset the router or restore to factory defaults. 
z If problems occur with your router, power it on and press the router’s reset 
button with a pencil tip (for less than 3 seconds) and the router will reboot 
and ,...

 5 3) WPS 
Wi-Fi Protected Setup (WPS) is the simplest way to build connection between 
wireless network clients and this ADSL router. Press this button on the router 
and enable WPS function of the wireless clients, the router and clients will 
automatically configure the security key and connect directly. Please note that 
the router will wait for WPS requests from wireless clients in 2 minutes after  
the WPS button is pressed. 
 
4) Power Jack 
Please plug the power adapter attached with the ADSL...

 6 Blinking No connection 
On The LAN cable is connected to the router 
Off No network connection. 
LAN LNK/ACT 
 (Port 1-4) 
Blinking Network traffic transferring or receiving through 
the LAN port 
 
 
  

 7
2. Hardware Installation 
Step 1. Connect the ADSL Line 
Use the supplied RJ-11 telephone cable, connect the router from the ADSL port 
to your telephone socket with an ADSL micro filter plugged in. 
 
Step 2. Connect the router to your LAN network 
Connect the router to your PC, hub or switch by attached the Ethernet cable to 
the LAN port of the router.  
 
 
 
Step 3. Connect the Power Adapter to the Router 
Connect the power adapter to the power jack on the rear panel of the router and 
switch on...

 8
3. Setup Wizard 
You can configure the router by running the Setup Wizard in the CD-ROM 
provided in the package. The wizard provides quick setup for the Internet 
connection, SSID, wireless security, firmware upgrade and changing router’s 
password. When you start the Setup Wizard, you will get the following Welcome 
screen. Please choose the language to start with and follow the easy steps in the 
Wizard. No instruction for the Setup Wizard is given here. 
 
If you lost the CD-ROM or you prefer the...

 9
 
 
 
 
 
  

 10
 
 
Please choose the product type which you bought  . 
 
 
 
  

 11 The default password is “ 1234 “ . 
 
Please select your country and ISP .If the country or ISP is not listed , please 
select “Others” from the list.  
 
Click” Next “ to finish all configurations of Internet Connection , Wireless setting 
and Firmware Upgrade .   

 12
4. IP Address Setting 
If you lost the CD-ROM or you prefer the traditional web setup, please follow the 
procedures of chapter 4 and chapter 5 to configure the router. Using the router to 
get into the Internet, the PCs in the network must have Ethernet adapter installed 
and be connected to the router either directly or through a hub or switch. The 
TCP/IP protocol of each PC has to been installed and the IP Address of each PC 
has to be set in the same subnet as the router. 
 
The router’s default...