Dukane Liquid Crystal Projector Model 8055 Users Manual

Liquid Crystal Projector
Model 8055
USERS MANU AL 

Thank you for purchasing this projector.• The information in this manual is subject to change without notice.\
• The manufacturer assumes no responsibility for any errors that may \
appear in this manual. 
• The reproduction, transmission or use of this document or contents \
is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT :
• VGA and XGA are registered trademarks of the International Business\
 Machines Corporation.
• Apple and Mac are registered trademarks of Apple...

Projector Featuresœ œœ
œœ
œœ
œœ
œœ
œœ
œ
3
Preparationœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
3
Part Namesœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
4
The Projectorœœœœœœœœœ4
Fastening The Lens Capœœœœ4
The Remote Controlœœœœœœ6
Setting Upœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
7
Arrangementœœœœœœœœœ7
Adjusting The Projector’s 
Elevatorœœœœœœœœœœœ8
Connecting Your Devicesœœœœ9
Connecting Power Supplyœœœ11
Remote...

3
●Ultra High BrightnessCrisp, ultra-bright presentations is achieved by using a UHB (ultra hig\
h brightness) lamp and a highly
efficient optical system.
●Whisper Mode EquippedSpecial mode is available for reducing projector noise to achieve quiete\
r operation.
●User Memory FunctionThis projector can memorize 4 settings by MY MEMORY function.
●Partial Magnification FunctionInteresting parts of images can be magnified for closer viewing. 
●Keystone Distortion CorrectionQuick correction of distorted...

4
StrapRivet
Strap
hole
Part Names
The Projector
Zoom ring
Focus ringAir filter cover
(An air filter is
inside.)

Elevator button
Elevator feet
Indicates the corresponding
reference page
Lens cap
Lens
(The picture is
projected from
here.)Remote sensor

Projector (Front/Right)
Fastening The Lens Cap
To avoid losing, please fasten the lens cap to the projector using the strap.
1Fix the strap to the strap ring of lens
cap, as the right drawing.
2Put one piece of the strap into the
groove on...

5
AC inlet
CONTROL port
VIDEO port 
AUDIO OUT port
AUDIO IN port
(from a computer) 
S-VIDEO port
COMPONENT VIDEO - Y
COMPONENT VIDEO - CB/PB
COMPONENT VIDEO - CR/PR
AUDIO            R port
L port
(from a video equipment)

Power switch
RGB IN port
Projector (Rear/Left)
STANDBY/ONINPUTPOWER
LAMP
TEMP
MENU
POWER indicator
tells the state of power
supply. Refer to the section
“Power ON/OFF”.
INPUT button
toggles between the signal
ports.
MENU buttons
operate the menu function....

6
The Remote Control(STANDBY/ON)
button
prepares for turning the
power on/off.
VIDEO button
toggles between the signal 
ports of VIDEO, S-VIDEO
and COMPONENT VIDEO.
MENU button
opens/closes the menu.
RGB button
selects the input signal of
RGB port.
BLANK button
blanks the screen
temporarily.
SEARCH button
searches for an input
signal between the
following signal ports of
RGB, VIDEO, S-VIDEO
and COMPONENT VIDEO. 
VOLUME button
turns on/off the VOLUME
mode.
In the VOLUME mode,
To adjust the volume,
use the...

7
Setting Up
Arrangement
WARNING• Install the projector in a suitable environment according to
instructions of the “User’s Manual – Safety Guide” and this manual.
• The power outlet should be close to the projector and easily accessible.
Refer to the illustrations and tables below to determine the screen size and projection
distance.
The values shown in the table are calculated for a full size screen:800·600
(a):Distance from the projector to the screen (±10%)
(b):Distance from the lens center to the...

8
Adjusting The Projectors Elevator
CAUTION• If you press the elevator buttons without holding the projector, the
projector might crash down, overturn, smash your fingers and possibly result in
malfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLD
THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to make adjustments if the surface on which you need to set
the projector is uneven or if you otherwise need to adjust the...