Dukane Imagepro 8958a Users Manual

9
ENGLISH
Turning on the power
1. Make sure that the power cord is fi rmly and correctly connected to the 
projector and the outlet.
2. Make sure that the POWER indicator is 
steady orange. Then remove the lens 
cover.
3. Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the 
POWER indicator will begin blinking in 
green. When the power is completely on, the 
indicator will stop blinking and light in steady 
green.
WARNING  ►A strong light is...

10
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven to 
the left or right, use the elevator feet to place the projector 
horizontally. Using the feet can also tilt the projector 
in order to project at a suitable angle to the screen, 
elevating the front side of the projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
To loose an 
elevator...

11
ENGLISH
VIDEO button
COMPUTER button
ASPECT button
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWNONOFF
FREEZEUP
ー＋VOLUME
1 2
ENTER
VOLUME+ button
VOLUME- button
MUTE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWNONOFF
FREEZEUP
ー＋VOLUME
1 2
ENTER
Displaying the picture
1. Activate your signal source. Turn the 
signal source on, and make it send...

12
NOTE  • The ASPECT button does not work when no proper signal is inputted.
• There may be some noise and/or the screen may fl icker for a moment when 
an operation is made. This is not a malfunction.
• For the details of how to adjust the picture, please see  User’s Manual - 
Operating Guide . 
CAUTION  ►If you wish to have a blank screen while the projector's lamp is 
on, use one of methods below.
- Use the supplied lens cover.
- Use the BLANK function (see User’s Manual - Operating Guide )....

13
ENGLISH
Replacing the lamp
A lamp has fi nite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, make contact with your dealer and tell the lamp type number .
Type number : 456-8958H-RJ
1. Turn the projector off, and unplug the power cord.  Allow...

14
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, if the 
bulb bursts, it is possible for shards of glass to fly into the lamp housing, and 
for gas containing mercury and dust containing fine particles of...

15
ENGLISH
Cleaning and replacing the air fi lter
Please check and clean the air fi lter periodically. When the indicators or a 
message prompts you to clean the air fi lter, comply with it as soon as possible.
The air fi lter of this projector consists of a fi lter cover and a fi lter unit with two 
types of fi lter. If one or both of the fi lters are damaged or heavily soiled, replace 
the fi lter unit with a new one.
Request for a fi lter unit with the following type number from your dealer when...

16
Cleasning and replacing the air filter  (continued)
10. Put the filter cover back into the place.
11 . Turn the projector on and reset the filter time using the FILTER TIME item 
in the EASY MENU.
(1)   Press the MENU button to display a menu.
(2)   Point at the FILTER TIME using the ▲/▼ cursor buttons, then press the 
► cursor (or the ENTER / the  RESET) button. A dialog will appear.
(3)   Press the ► cursor button to select the “OK” on the dialog. It performs 
resetting the filter time.
NOTE
  •...

17
ENGLISH
NOTE  • The information in the CD-ROM is subject to change without notice.
Please check our website where you may find the latest information for this 
projector. ( 19)
• No responsibility is taken for any obstacle and defect to hardware and 
software of your computer as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,  reproduced or republished without notice to our company.
Using the CD manual
The other manuals for this product are...

18
ItemSpecification
Product name Liquid crystal projector
Liquid Crystal 
Panel 8958A, 8959A:
  
786,432 pixels (1024 horizontal x 768 vertical)
8957WA:   1,024,000 pixels (1280 horizontal x 800 vertical)
Lamp 245 W UHP
Speaker 16 W mono (8 W x2)
Power supply/
Rated current AC100-120 V: 4.0 A, AC220-240 V: 2.0 A
Power 
consumption AC100-120 V: 370 W, AC220-240 V: 350 W
Temperature 
range 5 ~ 35 °C (Operating at an altitude up to 7500 ft.(2286 m))
5 ~ 30 °C (Operating at an altitude over 7500 ft.(2286...