Dukane Imagepro 8943a Projector Users Manual

							
3

INPUT Menu
INPUT Menu
From the INPUT menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor 
button on the projector or remote control, or ENTER 
button on the remote control to execute the item. Then 
perform it according to the following table.
ItemDescription
PROGRESSIVE
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó TURN OFF  
• This function is performed only for an interlaced signal at the VIDEO or S-VIDEO input, and for 525i (480i), 625i (576i) or 1125i (1080i) signal at the COMPONENT VIDEO or HDMI input.
• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.
VIDEO NR
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW   
• This function is performed only for the VIDEO or S-VIDEO 
input, and for 525i (480i), 625i (576i) or 1125i (1080i) signal at the COMPONENT VIDEO or HDMI input.
• When this function is excessive, it may cause a certain degradation of the picture. 
3D-YCS
Using the ▲/▼ buttons switches the 3D-YCS mode.
STILL ó MOVIE ó TURN OFF     
• This function performs only at a VIDEO input of NTSC, and PAL.
• MOVIE is the mode for images with a lot of motions like movies, and STILL is the mode for images with few motions or completely still ones like slides.
COLOR SPACE
Using the ▲/▼ buttons switches the mode for color space.
AUTO ó RGB ó SMPTE240 ó REC709 ó REC601      
• This item can be selected only for an RGB signal or a component video signal (except 525i (480i), 625i (576i) and SCART RGB).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.
(continued on next page) 
						

							
3

INPUT Menu
INPUT Menu (continued)
ItemDescription
COMPONENT
Using the ▲/▼ buttons switches the function of the COMPONENT (Y, CB/PB, Cr/Pr) port.
COMPONENT ó SCART RGB
When the SCART RGB is selected, the COMPONENT (Y, CB/PB, Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer.
VIDEO FORMAT
Set the video format for the s-video port and video port.
(1) Use the ◄/► buttons to select the input port.
(2) Using the ▲/▼ buttons switches the mode for video format.
AUTO  ó  NTSC  ó  PAL  ó  SECAM
      N-PAL ó M-PAL ó NTSC4.43 
• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.
HDMI
Using the ▲/▼ cursor buttons changes the HDMI signal mode.
AUTO ó NORMAL ó ENHANCED     
Feature
AUTOSelecting the optimum mode automatically.
NORMALSuitable for DVD signals (16-235)
ENHANCEDSuitable for VGA signals (0-255)
• If the contrast of the screen image is too strong or too weak, try finding a more suitable mode.
VIDEO
CONTROL
AUDIO IN 1AUDIO IN 2
REMOTE CONTROL   S-VIDEOAUDIOOUT  R  L R  L   AUDIO IN 3   AUDIO IN 4
RGB OUTRGB1RGB2M1-DCB/PBYCR/PR
LAN
SCART OUT
VideoGBR
(continued on next page) 
						

							
33

INPUT Menu
ItemDescription
FRAME LOCK
Set the frame lock function on/off for each port.
(1) Use the ▲/▼ buttons to select one of following ports.
RGB1 ó RGB2 ó HDMI
                QUIT
(2) Use the ◄/► buttons to turns the frame lock function on/off .
TURN ON ó TURN OFF
• This item can be performed only on a signal  with a vertical frequency of 50 to 60 Hz.
• When the TURN ON is selected, a moving pictures are displayed more smoothly.
• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.
RGB IN
Set the RGB input signal type for the RGB port.
(1) Use the ◄/► buttons to select the RGB port to be set.
RGB1 ó RGB2
(2) Use the ▲/▼ buttons to select the RGB input signal type.
AUTO ó SYNC ON G OFF
• Selecting the AUTO mode allows you to input a sync on G signal or component signal from the port.
• In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and select the SYNC ON G OFF, and then reconnect the signal.
INPUT Menu (continued)
(continued on next page) 
						

							
34

INPUT Menu
INPUT Menu (continued)
ItemDescription
RESOLUTION
The resolution for the RGB1 and RGB2 input signals can be set on this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button.The RESOLUTION menu will be displayed.
(2)  In the RESOLUTION menu select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
(3) Pressing the ► or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and horizontal size. The INPUT-INFORMATION dialog (46) will be displayed.
(4) To set a custom resolution use the  ▲/▼ buttons to select the CUSTOM and the CUSTOM RESOLUTION BOX will be displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the  ▲/▼/◄/► buttons.It is not guaranteed to work this function properly on any resolutions.
(5) To save the setting place the cursor on the right-most digit and press the ► button.The horizontal and vertical positions, clock phase and horizontal size will be automatically adjusted.After the INPUT-INFORMATION (46) dialog has displayed for about 10 seconds the screen will return to the RESOLUTION menu displaying the changed resolution.
(6) To revert back to the previous resolution without saving changes place the cursor on the left-most digit and press the ◄ button.The screen will then return to the RESOLUTION menu displaying the previous resolution.
• For some pictures, this function may not work well.
RESOLUTION MENU
CUSTOM RESOLUTION BOX 
						

							
35

SETUP Menu
SETUP Menu
From the SETUP menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
according to the following table.
ItemDescription
AUTO 
KEYSTONE EXECUTE
Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again.
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.• When the projector is placed on the level (about ±3°), this function may not work.• When the projector is inclined to near ±30 degree or over, this function may not work well.• When the vertical lens shift is not set fully upward (not set fully downward for the optional lens type FL-601 only (45)), this function may not work well.• When the horizontal lens shift is not set to the center, this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
KEYSTONE 
Using the ▲/▼ buttons corrects the vertical keystone distortion.
Shrink the top of the image ó Shrink the bottom of the image
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When the horizontal lens shift is not set to the center, this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
(continued on next page) 
						

							
36

SETUP Menu
ItemDescription
KEYSTONE 
Using the ▲/▼ buttons corrects the horizontal keystone distortion.
Shrink the right of the image ó Shrink the left of the image
• The adjustable range of this function will vary among inputs. For some input, this function may not work well.• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.• When the vertical lens shift is not set fully upward (not set fully downward for the optional lens type FL-601 only (45)), this function may not work well.• This function will be unavailable when the Transition Detector is on (51).
WHISPER
Using the ▲/▼ buttons turns off/on the whisper mode.
NORMAL ó WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT 
If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (51) will be displayed when projector is restarted after the power switch is turned off.
SETUP Menu (continued) 
						

							
37

AUDIO Menu
AUDIO Menu
From the AUDIO menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
ItemDescription
VOLUMEUsing the ▲/▼ buttons adjusts the volume.High ó Low
TREBLEUsing the ▲/▼ buttons adjusts the treble level.High ó Low
BASSUsing the ▲/▼ buttons adjusts the bass level. High ó Low
SRS WOW
Using the ▲/▼ buttons switches the mode for SRS WOW mode. HIGH ó MID ó OFF    
• SRS WOW™ accomplishes this by providing a panoramic three-dimensional audio image that extends the sound field in both the horizontal and vertical planes, and lowers the perceived bass response well beyond the low frequency limitations of the drivers. Adjust it depending on the user's preference.
SPEAKERUsing the ▲/▼ buttons turns the speaker function on/off. TURN ON ó TURN OFF• When the TURN ON is selected the built-in speaker works.
AUDIO
Allocates the audio ports.(1) Choose a picture input port using the ▲/▼ buttons.          RGB1  ó  RGB2  ó  HDMI 
QUIT ó VIDEO ó S-VIDEO ó COMPONENT
(2) Select the audio port to be interlocked with the input port using the ◄/► buttons.1 ó 2 ó 3 ó 4 ó  ó H• H is abbreviation of HDMI.• H can be selected for HDMI port only. When H is selected, the audio signal to HDMI port will be output if HDMI is chosen as a display source.• When  is selected for an input, the audio will not be output if the input is chosen as a display source.
HDMI AUDIOThe HDMI AUDIO is set to 1 as default. In case the HDMI audio does not work well, try 2.1 ó 2 
• The speaker sound may distorted or the case may be trembling when 
the volume is too high or treble/bass is emphasized or WOW is activated. In that 
case, make the volume reduced, bass/treble low or WOW effect to be weakend.
NOTE 
						

							
38

SCREEN Menu
SCREEN Menu
From the SCREEN menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
ItemDescription
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
SUOMI ó POLSKI ó TÜRKÇE
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL ó ITALIANO
NORSK ó NEDERLANDS ó PORTUGUÊS ó 日本語
    ó    ó        ó SVENSKA ó
MENU POSITIONUsing the ◄/►/▲/▼ buttons adjusts the menu position.To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature 
(22). It is displayed by pressing the BLANK button on the remote control.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK  
Feature
MyScreenScreen can be registered by the MyScreen item (40).
ORIGINALScreen preset as the standard screen.
BLUE, WHITE, BLACKPlain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.
(continued on next page) 
						

							
39

SCREEN Menu
SCREEN Menu (continued)
ItemDescription
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.
MyScreen ó ORIGINAL ó TURN OFF    
Feature
MyScreenScreen can be registered by the MyScreen item (40).
ORIGINALScreen preset as the standard screen.
TURN OFFPlain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen (38) after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.• When the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48), the START UP is fixed to MyScreen.
(continued on next page) 
						

							
40

SCREEN Menu
ItemDescription
MyScreen
This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
1.  Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if you start capturing an image from the current screen.Please wait for the target image to be displayed, and press the ENTER button on the remote control when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET or ESC button on the remote control. 
2.   Using the ▲/▼/◄/► buttons adjusts 
the frame position. Please move the frame to the position of the image which you want to use. The frame may not be able to be moved for some input signals. To start registration, press the ENTER button on the remote control.To restore the screen and return to the previous dialog, press the RESET or ESC button on the remote control. Registration takes several minutes. When the registration is completed, the registered screen and the following message is displayed for several seconds:“MyScreen registration is finished.”If the registration failed, the following message is displayed:“A capturing error has occurred. Please try again.” • This item cannot be selected for an HDMI signal.• This function cannot be selected when the TURN ON is selected to the MyScreen Lock item (below).• This function cannot be selected when the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48).
MyScreen Lock
Using the ▲/▼ buttons turns on/off the MyScreen lock function.
TURN ON ó TURN OFFWhen the TURN ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen.• This function cannot be selected when the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (48).
SCREEN Menu (continued)
(continued on next page)