Dukane Imagepro 8942 Liquid Crystal Projector Users Manual

							29
Multifunctional Settings (continued) Multifunctional Settings (continued)
AUTO Menu
With the AUTO menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
ItemDescription
ADJUST
Pressing the  (or the ENTER) button performs the automatic adjustment. 
■At a RGB signal
The vertical position (V POSITION), the horizontal position (H POSITION), the
clock phase (H PHASE) and the horizontal size (H SIZE) will be automatically
adjusted.
memoMake sure that the application window is set to its maximum size prior to
attempting to use this feature. Dark pictures may still be incorrectly adjusted.
Use a bright screen when adjusting.
■At a video signal
The signal type mode best suited for the respective input signal will be
selected automatically.
memoThis function is available only when the AUTO is selected to the item
“VIDEO” of the INPUT menu. For a component video signal, the signal type is
identified automatically independently of this function.
memoThis operation requires approximately 10 seconds, and the message
“AUTO IN PROGRESS” is displayed during the operation. 
memoThis operation may not work well at some signals. If the picture
becomes unstable (ex. a irregular picture, a color lack), please select the
suitable mode to the item “VIDEO” of the INPUT menu.
POWER OFF
Set the time using the  /  buttons. :
Long (max. 99 minutes) 
Short (min. 0 minute = DISABLE)
ex.
When the time is set to 1 to 99, the projector lamp will go off and the
STANDBY/ON indicator begins blinking when the passed time with a proper
signal (without no-signal and an unsuitable signal) reaches at the set time.
Please refer to the section “Turning Off The Power”.
POWER ON
Select the TURN ON or the TURN OFF using the  /  buttons.:
TURN ON 
TURN OFF
When the TURN ON is selected, you can turn the projector on without pressing
the STANDBY/ON button. Please refer to the section “Turning Off The Power”.
: SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORKADJUST
POWER OFF
POWER ON
SEARCH
RESET0 min
TURN ON
TURN ON
(This table is continued to the following page.)
AUTO
POWER OFF
ENABLE
1min
AUTO
POWER OFF
DISABLE
0min
$19&/(0(~
						

							30
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
SEARCH
Select the TURN ON or the TURN OFF using the  /  buttons. :
TURN ON 
TURN OFF
When the TURN ON is selected, detecting no signal cycles through input ports
and displays the picture of retrieved signal.
memoWhen the TURN ON is selected, pressing the RGB button selects the
M1-D ports, and pressing the VIDEO button selects the COMPONENT port. 
memoIf no signal is found or the projector is unstable to find an input signal at
any of its ports, it will return to the state it was in prior to the search.
RESET
Select the EXECUTE using the  button to reset the AUTO menu items. :
EXECUTE CANCEL
The items of the AUTO menu are collectively returned to the initial setting. Note
that the item “ADJUST” is not reset.
AUTO Menu (continued)
BNCM1-D RGB
VIDEO S-VIDEO
COMPONENT
$19&/(0(~
						

							31
Multifunctional Settings (continued)
Multifunctional Settings (continued)
SCREEN Menu
With the SCREEN menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
: 
SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORK BLANK
START UP
MyScreen
MyScreen SIZE
MyScreen LOCK
MENU POSITION
MESSAGE
RESET BLACK
ORIGINAL
x1
TURN OFF
TURN ON
ItemDescription
BLANK
Select a type of the BLANK screen using the  /  buttons. :
MyScreen  
ORIGINAL  
BLUE  
WHITE  
BLACK
The BLANK screen is the screen, which is displayed by pressing the BLANK\
button. The MyScreen is the screen you can register a desired screen, an\
d the
ORIGINAL is the existing standard screen. The BLUE, the WHITE and the
BLACK are the non-pattered (plain) screens in each color. 
memo  To avoid remaining as an afterimage, the MyScreen and the ORIGINAL
screens will change to the BLACK screen after several minutes.
memo For the MyScreen, please refer to the item “MyScreen” in this tabl\
e.
START UP
Select a type of the START UP screen using the  /  buttons. :
MyScreen  
ORIGINAL  
TURN OFF
The START UP screen is the screen, which is displayed by detecting no si\
gnal
or an unsuitable signal. 
The MyScreen is the screen you can register a desired screen, and the
ORIGINAL is the existing standard screen. When the TURN OFF is selected,\
the BLUE is used.
memo To avoid remaining as an afterimage, the MyScreen and the ORIGINAL
screens will change to the BLANK after several minutes. If also the BLAN\
K
screen is the MyScreen or the ORIGINAL, it will change to the BLACK scre\
en.
memo About the MyScreen, please refer to the item “MyScreen” in this ta\
ble.
About the BLUE, BLACK and BLANK screens, please refer to the item “BL\
ANK”
in this table.
MyScreenPressing the (or the ENTER) button starts the MyScreen registration. Please
see the flow chart on the following page.
MyScreen SIZESelect the size of the MyScreen using the  /  buttons. : x1  
 FULL
MyScreen LOCK
Select the TURN ON or the TURN OFF using the  /  buttons.:
TURN ON  
TURN OFF
The TURN ON disables the operation of the item “MyScreen” of this \
SCREEN
menu.
MENU POSITION
After pressing the     (or ENTER) button,  adjust the menu position   buttons. :
Up 
Left   +   Right

Down
memo  To finish this operation, press the ESC button but not the button.
(This table is continued to the following page.)
$19&/(0(~
						

							32
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
MESSAGE
Select the TURN ON or the TURN OFF using the  /  buttons. :
TURN ON 
TURN OFF
When the TURN ON is selected, the following message function works.
The message of the “AUTO IN PROGRESS” for the auto adjustment. 
The message of the ”NO INPUT IS DETECTED”
The message of the ”SYNC IS OUT OF RANGE”
The message of the ”Searching …”
The message of the “Detecting …”
The indication of the input signal by input change.
The indication of the aspect ratio by changing the aspect ratio.
The indication of “FOCUS” by adjusting the focus.
RESETSelect the EXECUTE using the  button to reset the SCREEN menu items. :
EXECUTE CANCEL
The items of the SCREEN menu are collectively returned to the initial setting.
SCREEN Menu (continued)
How to register your picture as the MyScreen
MyScreen is pointed on the SCREEN menu.
The MyScreen
menu appears.
Do you capture the picture from
the current screen?
Registering. 
It takes about 1 minute to register.
Just when the picture registration is completed
the registered screen and
the message of the right is displayed for a few seconds.
If the picture registration failed,
the message of the right is displayed for a few seconds.The picture freeze and the frame for capturing appears.
Move the frame to the position of the picture
which you want to use, using     /    /    /    buttons,
and press the ENTER button to register.
NO: Press the ESC/RESET button
YES: Press the ENTER button If the ESC/RESET 
button is pressed ...
Press the    button
:NOESCENT:YES
MyScreen
Do you start capturing this picture?
:RETURNESCENT:NEXT
MyScreen
Move the capture areaas you want.
My Screen
45%
MyScreen registration is finished.
A capturing error has occurred.
Please try again.
$19&/(0(~
						

							33
Multifunctional Settings (continued)
Multifunctional Settings (continued)
OPTION Menu
With the  OPTION menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
: 
SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORKV OLUME
SPEAKER
IR REMOTE
IR REMOTE ID
LAMP TIME
FILTER TIME
SERVICE
RESET 16
TURN ON
ALL
1234 h
4321 h
ItemDescription
VOLUMEAdjust the volume using the  /  buttons. : 
High  
Low
SPEAKERSelect the TURN ON or the TURN OFF using the  /  buttons. :
TURN ON  
TURN OFF
When the TURN ON is selected, the built-in speaker works.
IR REMOTE
Select a remote sensor using the  /  button (1), then switch
it using the ENTER button (2). : (1) FRONT  
TOP  
REAR   (2)  (Off)   
(On)
memo A sensor cannot be turned off when the other two are off.
Always at least one sensor is on.
IR REMOTE ID
Select a number as an ID number for remote control using the  /  buttons. :ALL  
1 
 2 
 3
The projector is controlled by the remote control whose ID CHANGE switch\
 is
set into the position of the same number as this number. When the ALL is\
selected, the projector is controlled by a remote control irrespective o\
f the
position of the ID CHANGE switch. 
memo Please refer to the section “Using The Remote ID Feature”.
LAMP TIME
Pressing the RESET button for about 3 seconds displays the LAMP TIME men\
u. 
Select the RESET using button to reset the timer. :
RESET  CANCEL
Selecting the RESET resets the count of the lamp timer to 0. 
memo Perform this function only when you have replaced the lamp. The lamp
timer counts the used time of the current lamp, to display the messages \
about
the lamp. Incorrect performing causes incorrect operation of the message\
s.
memo About replacing the lamp, please refer to the section” Lamp”.
FILTER TIME
Pressing the RESET button for about 3 seconds displays the FILTER TIME
menu. 
Select the RESET using button to reset the timer. :
RESET  CANCEL
Selecting the RESET resets the count of the lamp timer to 0. 
memo Perform this function only when you have cleaned or replaced the air
filter. The filter timer counts the used time of the air filter after cl\
eaning or
replacement, to display the messages about the air filter. Incorrect per\
forming
causes incorrect operation of the messages.
memo About caring for the air filter, please refer to the section “Air Fil\
ter”.
     OPTION
  IR REMOTE
FRONT
TOP
REAR
 ENT
(This table is continued to the following page.)
$19&/(0(~
						

							34
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
SERVICE
Pressing the (or the ENTER) button calls the SERVICE
menu. 
SERVICE Menu
Select an item using the  /  buttons, and press the
(or the ENTER) button to per form each function. :
FANSPEED 
AUTO ADJUST 
LENS TYPE 
LENS LOCK
FANSPEED
Select the fan speed level using the  /  buttons. :
HIGH 
NORMAL
The HIGH ups rotation speeds of fans, though. Please use this
function in using a projector at highlands etc.
memoNote that the projector is noisier when the HIGH is
selected.
AUTO
ADJUST
Select the ENABLE or the DISABLE using the  / 
buttons. :
ENABLE 
DISABLE
When you want to keep the current adjustment state, select
the DISABLE. When the ENABLE is selected, detecting a
signal change to a RGB signal performs the automatic
adjustment of the vertical position (V POSITION), the horizontal
position (H POSITION), the clock phase (H PHASE) and the
horizontal size (H SIZE).
LENS TYPE
Select the lens type currently used using the  /  buttons. :AUTO 
1 
2 
3 
4 
5
Please select depending on the following. 
AUTO: automatically selects optimum mode.
1: for a standard lens (Type NL-500 etc.)
2: for a fixed short throw lens (Type FL-501 etc.)
3: for a short throw lens (Type SL-502 etc.)
4: for a long throw lens (Type LL-503 etc.)
5: for a super long throw lens (Type LL-504 etc.)
memoThis setting has an influence on the keystone distortion
etc. 
memoAbout the optional lens, ask your dealer.
LENS LOCK
Select the TURN ON or the TURN OFF using the/ buttons. :
TURN ON 
TURN OFF
Selecting the TURN ON locks the adjustment of the lens shift,
the zoom and the focus.  
RESET
Select the EXECUTE using the button to reset the OPTION menu items. :
EXECUTE CANCEL
The items of the OPTION menu are collectively returned to the initial setting.
Note that the items “VOLUME”, “LAMP TIME” and “FILTER TIME” are not reset.
: SELECT
SERVICE
FANSPEED
AUTO ADJUST
LENS TYPE
LENS LOCKNORMAL
ENABLE
AUTO
TURN OFF
OPTION Menu (continued)
$19&/(0(~
						

							35
Multifunctional Settings (continued) Multifunctional Settings (continued)
NETWORK Menu
This projector provides the NETWORK function. If you use this
function, please set up the projector according to the Network
environment in which you use it.
memoWhen you use a Network suitable to the DHCP function, the following
operation is not required commonly, because the TURN ON is selected to
the item “DHCP” at the shipment time. Please see the section “Network
Setting Up”.: SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORKSETUP
DHCP
INFORMATION
RESETTURN OFF
ItemDescription
SETUP
Pressing the (or the ENTER) button calls the IP
ADDRESS menu. 
memoThis item performs only when the TURN OFF
is set to the item “DHCP” of this NETWORK menu.
The IP Address is identification number of the projector on the Network.
1. Set the IP Address using the  /  buttons. 
memoThe same number as the IP Address of other units cannot be used.
Pressing the (or the ENTER) button at the IP
ADDRESS menu calls the SUBNET MASK menu. The
SUBNET MASK is an address of the Network.
2. Set the same number as the address of the Network to be used.
Pressing the (or the ENTER) button at the
SUBNET MASK menu calls the DEFAULT GATEWAY
menu. The DEFAULT GATEWAY is the address of
the main device.
3. Set the same number as the address of the device as gateway to an outer
Network.
DHCP
Select the TURN ON or the TURN OFF using the  / 
buttons. :
TURN ON 
TURN OFF
When you use a Network unsuitable to the DHCP function, select the TURN
OFF.
INFORMATION
Pressing the (or the ENTER) button displays the
INFORMATION menu. 
The INFORMATION menu shows the information
about the current Network setting as illustrated
below.
RESETSelect the EXECUTE using the  button to reset the NETWORK menu items. :
EXECUTE CANCEL
The items of the NETWORK menu are collectively returned to the initial setting. 
:RETURNESCENT:NEXT
NETWORK - SETUPIP ADRRESS
192 .   168 .     1 .      24
:RETURNESCENT:NEXT
NETWORK - SETUPSUBNET MASK
255 .   255 .   255 .      1
:RETURNESCENT:NEXT
NETWORK - SETUPDEFAULT GATEWAY
255 .   255 .   255 .      0
NETWORK-INFORMATION
 IP ADRRESS  192. 168. 1. 24
SUBNETMASK  255. 255. 255. 0
DEFAULT GATEWAY  255. 255. 255. 0
MAC ADRRESS  00. E0. 47. 03. 0C. D8
NETWORK
DHCP
TURN ON
TURN OFF
$19&/(0(~
						

							36
Network Setting Up
Network Setting Up
This projector provides the NETWORK function. If you use this function, \
please consult
your dealer for information.
To start, connect the NETWORK port to a gateway device via a RJ-45 (10B\
ASE-1) cable,
then set up the projector according to the Network environment in which \
you use it.
When you use a Network unsuitable to the DHCP functionPlease set the IP Address, the Subnet Mask, the Gateway and the DHCP (o\
n/off) using
the NETWORK menu, referring to the section “NETWORK Menu”.
When you use a Network suitable to the DHCP function
or has been set up
You can set the IP Address, the Subnet Mask, the Gateway and the DHCP (\
on/off) using
a Web Browser of the computer connected to the Network. Although it need\
s a Web
Browser of Internet Explorer 4.0 or higher.
Input the same IP address as set to the projector, to the Web Browser of\
 the computer
connected to LAN.
ex. Case of IP Address = 192.168.1.11
1) Input “http://192.168.1.11”.
2) Click “ENTER”.
3) Input the required data according to the screen.
4) Make sure of the input data, then click Write.
memo
These setting will be active after reboot. These
setting will be stored, and used when DHCP is OFF.
5) Click “Return to top page”.
6) Click “REBOOT” to complete this operation.
$19&/(0(~
						

							37
Lamp
Lamp
The projector uses a high-pressure mercury glass lamp. The lamp can 
break with aloud bang, or burn out,if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn\
 out soon after
you start using them. In addition, when the bulb bursts, it is possible \
for  shards of
glassto fly into the lamp housing, and for gas containing mercuryto escape from the
projector’s vent holes.
About disposal of a lamp • This product contains a mercury lamp; do not put in
trash. Dispose of in accord with environmental laws.
For lamp recycling, go to www.lamprecycle.org. (in USA) 
For product disposal, contact your local government agency or www.eiae.o\
rg (in the
US) or www.epsc.ca (in Canada). 
For more information, call your dealer.
• If the lamp should break (it will make a loud bang when it does), unpl\
ugthe power cord from the outlet, and make sure to request a replacement
lamp from your local dealer. Note that shards of glass could damage the
projector’s internals, or cause injury during handling, so please do \
not try
to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), vent\
ilate the room well, and make sure not to breathe the gas that comes out of
the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lam\
p
to cool sufficiently. Handling the lamp while hot can cause burns, as we\
ll
as damaging the lamp.
• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in h\
igh
places is dangerous, so ask your local dealer to have the lamp replaced
even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
•  Use only the lamp of the specified type  456-8935
.
• If the lamp breaks soon after the first time it is used, it is possible \
that there are electrical problems elsewhere besides the lamp. If this
happens, contact your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the indicators or a message prompts you to replace the lamp (see the\
 section “Related Messages” and “Regarding the indicator Lamps”\
),
replace the lamp as soon as possible. Using the lamp for long periods of\
time, or past the replacement date, could cause it to burst. Do not use
old (used) lamps; this is a cause of breakage.
W ARNINGHIGH VOLTAGE    HIGH TEMPERATURE    HIGH PRESSURE
Disconnect the
plug from thepower outlet
$19\
&/(0(\b~Í
 
 


1.

Ö”´ 
						

							38
Lamp (continued) Lamp (continued)
After making sure that the projector has cooled
adequately, slide the knob of a lamp cover lock as
shown in the Figure. Then, one side of the lamp
cover is raised. Pull up the lamp cover and remove
it, as shown in the Figure. If the indicators or a message prompts you to replace the lamp, replace the lamp as soon
as possible.
Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at
least 45 minutes.
2
1
Contact your dealer to prepare a new lamp. Tell the dealer your lamp type number.
If the projector is mounted on the ceiling, or if the lamp has broken, also ask the
dealer to replace the lamp.
3
4Unscrew the 3 screws, and slowly pull out the lamp
by the handle. Be careful not to touch the inside of
the lamp case.
5Insert the new lamp, and tighten the 3 screws firmly
to lock it in place.
6Interlocking the 2 tabs of the lamp cover to the
projector, put the lamp cover on the projector. Then
push the point of the lamp cover to fix it, as shown in
the Figure. Make sure that the lamp cover does’t
come up.
7Turn on the projector, and reset the lamp timer.
(1) While the projector running, press the MENU button to open the menu.
(2) Choose the “OPTION” on the menu using the
/button, then press the
button or ENTER button.
(3) Choose the “LAMP TIME” using the
/button, then press and hold the
RESET button for 3 seconds.
(4) Choose the “RESET” using the button.
memoWhen the lamp has been replaced after the message of THE POWER WILL
TURN OFF AFTER 0hr. is displayed, complete the following operation within 10
minutes of switching power on.
memoIncorrectly resetting of the lamp timer (resetting without replacement, or
neglect of resetting after replacement) will result in incorrect message functions.
CO LAMPPC
INTERINPUTM1-DRGBBNG
S-VIDEO
STANDBY/ONTEMPVIDEOCOMPON
ENTLAMPKEYSTONESEARCHRESETMENUFOCUSLENS SHIFTZOOM
Lamp cover Lamp cover
knob
Tabs
In the case of replacement by yourself,
INTERINPUTM1-DRGBBNG
S-VIDEO
STANDBY/ONTEMPVIDEOCOMPONENTLAMPKEYSTONESEARCHRESETMENUFOCUSLENS SHIFTZOOM
CO LAMPPC
CO LAMPPC
INTERINPUTM1-DRGBBNG
S-VIDEO
STANDBY/ONTEMPVIDEOCOMPONENTLAMPKEYSTONESEARCHRESETMENUFOCUSLENS SHIFTZOOM
Screws
CO LAMPPC
Replacing The Lamp
$19&/(0(~