Dukane Imagepro 8919h Projector Users Manual

11
ENGLISH
Turning off  the power
1. Press the STANDBY/ON button on the 
projector or the remote control.
The message “Power off?” will appear on 
the screen for about 5 seconds.
2. Press the STANDBY/ON button again 
while the message appears. 
The projector lamp will go off, and the 
POWER indicator will begin blinking in 
orange. Then the  POWER indicator will 
stop blinking and light in steady orange 
when the lamp cooling is complete.
3. Attach the lens cover, after the POWER 
indicator turns in...

12
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time\
 could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them\
. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, make contact wit456-8755JDT01021
1. Turn the projector off, and unplug the power cord. 
Allow the projector to cool for at least 45 minutes.
2. Prepare a...

13
ENGLISH
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, ha\
ndled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition,\
 when 
the bulb bursts, it is possible for shards of glass to fly into the la\
mp housing, 
and for gas containing mercury to escape from the...

14
Please check and clean the air filter periodically. When the indicators or a message 
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two 
kinds of filters inside. Replace the filters when they are damaged o\
r too soiled. To prepare 
the new filters, make contact with your dealer and tell the following \
type number.
Type number : MU06481 (Filter set)
When you replace the lamp, please replace the air filter. An air 
filter of specified type will come together with a...

15
ENGLISH
Using the CD manual
The other manuals for this product are written into the included CD-ROM \
titled 
“User’s Manual (detailed)”. Before using the CD-ROM, please read the foll\
owing 
to ensure the proper use. 
 System requirements
The system for using the CD-ROM requires the following. 
  Windows®:  OS:Microsoft® Windows® 98, Windows® 98SE,  
Windows NT®4.0, Windows® Me,  
Windows® 2000/Windows® XP or later
 CPU:Pentium® processor 133MHz / Memory:32MB or more
  Macintosh®:  OS:Mac OS® 10.2 or...

16
Specifications
ItemSpecification
Product name Liquid crystal projector
Liquid Crystal Panel 786,432 pixels (1024 horizontal x 768 vertical)
Lens Zoom lens,  f = 19 ~ 23 mm    (approximately)
Lamp 210W UHP
Speaker 16W
Power supply AC 100-120V/3.7A, AC220-240V/1.8A
Power consumption 330W
Temperature range 5 ~ 35°C (Operating)
Size317 (W) x 98 (H) x 288 (D) mm
* Not including protruding parts. Please refer to the following figure\
.
Weight (mass) approx. 3.5kg
<
Ports Computer input port
COMPUTER IN1...

17
ENGLISH
Troubleshooting - Warranty and after-ser vice
If an abnormal operation (such as smoke, strange odor or excessive soun\
d) 
should occur, stop using the projector immediately. Otherwise if a problem occurs 
with the projector, first refer to the “Troubleshooting” of the “Operating Guide” in 
the CD and run through the suggested checks. 
If this does not resolve the problem, please consult your dealer or serv\
ice 
company. They will tell you what warranty condition is applied.
Please check the...