Dukane Imagepro 8919h Projector Users Manual

							11
ENGLISH
Turning off  the power
1. Press the STANDBY/ON button on the 
projector or the remote control.
The message “Power off?” will appear on 
the screen for about 5 seconds.
2. Press the STANDBY/ON button again 
while the message appears. 
The projector lamp will go off, and the 
POWER indicator will begin blinking in 
orange. Then the  POWER indicator will 
stop blinking and light in steady orange 
when the lamp cooling is complete.
3. Attach the lens cover, after the POWER 
indicator turns in steady orange.
Do not turn the projector on for about 10 minutes or more after turning \
it off. 
Turning the projector on again too soon could shorten the lifetime of som\
e 
consumable parts of the projector.
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION12
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTOMAGNIFYPAGE
      UPVOLUMEDOWNo
ONOFF9×
FREEZE
WARNING  ►Do not touch around the lamp cover and the exhaust vents 
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be 
close to the projector and easily accessible.
NOTE  • Please power off the projector after any connected devices are 
powered off.
• This projector has the AUTO OFF function that can make the projector turn off 
automatically. For more information, please see the “Operating Guide” in the  CD.
STANDBY/ON button POWER indicator 
						

							12
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time\
 could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them\
. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, make contact wit456-8755JDT01021
1. Turn the projector off, and unplug the power cord. 
Allow the projector to cool for at least 45 minutes.
2. Prepare a new lamp. If the projector is mounted on 
a ceiling, or if the lamp has broken, also ask the 
dealer to replace the lamp.
In case of replacement by yourself, follow the following 
procedure.
3. Loosen the screw (marked by arrow) of the lamp 
cover and then slide and lift the lamp cover to the 
side to remove it.
4. Loosen the 3 screws (marked by arrow) of the 
lamp, and slowly pick up the lamp by the handles. 
Never  loosen any other screws.
5. Insert the new lamp, and retighten firmly the 
3 screws of the lamp that are loosened in the 
previous process to lock it in place.
6. While putting the interlocking parts of the lamp 
cover and the projector together, slide the lamp 
cover back in place. Then firmly fasten the screw of 
the lamp cover.
7. Turn the projector on and reset the lamp time 
using the LAMP TIME item in the OPTION menu. 
(1) Press the MENU button to display a menu. 
(2) Point at the ADVANCED MENU in the menu using the  ▼/▲ button, then press the ► button.
(3) Point at the OPTION in the left column of the menu using  the ▼/▲button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button, then  press the ► button. A dialog will appear.
(5) 
Press the ► button to select “OK” on the dialog. It performs resetting the la\
mp time.
NOTE  • Please reset the lamp time only when you have replaced the lamp, \
for a suitable indication about the lamp.
CAUTION  ►Do not touch any inner space of the projector, while the lamp 
is taken out.
Lamp cover
4 3
6Handles 
						

							13
ENGLISH
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, ha\
ndled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition,\
 when 
the bulb bursts, it is possible for shards of glass to fly into the la\
mp housing, 
and for gas containing mercury to escape from the projector’s vent holes.
►About disposal of a lamp:  This product contains a mercury lamp; do not put 
it in a trash. Dispose of it in accordance with environmental laws. 
•   For lamp recycling, go to www.lamprecycle.org (in the US).
•   For product disposal, consult your local government agency  
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, ask your dealer.
• If the lamp should break (it will make a loud bang when it does),\
 
unplug the power cord from the outlet, and make sure to request a 
replacement lamp from your local dealer. Note that shards of glass 
could damage the projector’s internals, or cause injury during handling, 
so please do not try to clean the projector or replace the lamp yourself\
.
• If the lamp should break (it will make a loud bang when it does),\
 
ventilate the room well, and make sure not to breathe the gas that 
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power 
cord, then wait at least 45 minutes for the lamp to cool sufficiently. 
Handling the lamp while hot can cause burns, as well as damaging the lam\
p.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from 
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the 
shards will fall out when the cover is opened. In addition, working in 
high places is dangerous, so ask your local dealer to have the lamp 
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp 
replacing, make sure that the screws are screwed in firmly. Loose 
screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is poss\
ible 
that there are electrical problems elsewhere besides the lamp. If this 
happens, consult your local dealer or a service representative.
• 
Handle with care: jolting or scratching could cause the lamp bulb to bur\
st during use.
• Using the lamp for long periods of time, could cause it dark, not t\
o light 
up or to burst. When the pictures appear dark, or when the color tone 
is poor, please replace the lamp as soon as possible. Do not use old 
(used) lamps; this is a cause of breakage. 
Disconnect  the plug 
from the  power outlet
Replacing the lamp (continued) 
						

							14
Please check and clean the air filter periodically. When the indicators or a message 
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two 
kinds of filters inside. Replace the filters when they are damaged o\
r too soiled. To prepare 
the new filters, make contact with your dealer and tell the following \
type number.
Type number : MU06481 (Filter set)
When you replace the lamp, please replace the air filter. An air 
filter of specified type will come together with a replacement 
lamp for this projector.
1. Turn the projector off, and unplug the power cord. Allow the 
projector to sufficiently cool down.
2. Use a vacuum cleaner on and around the filter cover. 
3. While supporting the projector with one hand, use your 
other hand to pull the filter cover forward in the direction of 
the arrow.
4. Use a vacuum cleaner for the filter vent of the projector 
and the outer side of the filter unit.
5. Take the filters out while holding the filter cover.
6. Use a vacuum cleaner onto the both sides of the filters. 
When vacuuming up the fine meshed filter, hold it so it 
will not be sucked in. If the filters are damaged or heavily 
soiled, replace them with the new ones.
7. Put the filters back into the filter cover. Put the coarse 
meshed filter into a filter cover first. Then put the fine 
meshed filter on the coarse meshed one, turning its stitched 
side up.
8. Put the filter unit back into the projector.
9. Turn the projector on and reset the filter time using the 
FILTER TIME item in the EASY MENU. 
(1) Press the MENU button to display a menu. 
(2)  Point at the FILTER TIME using the ▼/▲ button, then  press the ► button. A dialog will appear.
(3)  Press the ► button to select “OK” on the dialog. It  performs resetting the filter time.
Cleaning and replacing the air filter
WARNING  ►Before taking care of the air filter, make sure the power cable 
is not plugged in, then allow the projector to cool sufficiently.
►
Use only the air filter of the specified type. Do not use the projec\
tor without the 
air filter or the filter cover. It could result in a fire or malfunction to the projector
.
►
Clean the air filter periodically. If the air filter becomes clogged by dust or the like, 
internal temperatures rise and could cause a fire, a burn or malfuncti\
on to the projector.
NOTE  • Please reset the filter time only when you have cleaned or repl\
aced 
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or  turn off the projector, to prevent the internal heat level rising. 
Filter cover
Filter unit
 Filter cover
Filter (fine meshed) Filter (coarse meshed)
2
4
3
7
Stitched  
side 
						

							15
ENGLISH
Using the CD manual
The other manuals for this product are written into the included CD-ROM \
titled 
“User’s Manual (detailed)”. Before using the CD-ROM, please read the foll\
owing 
to ensure the proper use. 
 System requirements
The system for using the CD-ROM requires the following. 
  Windows®:  OS:Microsoft® Windows® 98, Windows® 98SE,  
Windows NT®4.0, Windows® Me,  
Windows® 2000/Windows® XP or later
 CPU:Pentium® processor 133MHz / Memory:32MB or more
  Macintosh®:  OS:Mac OS® 10.2 or later
 CPU:PowerPC® / Memory:32MB or more
  CD-ROM drive:  4x CD-ROM drive
  Display:   256 color / 640x480 dots resolution
  Applications:   Microsoft
® Internet Explorer®4.0 and
 Adobe® Acrobat® Reader® 4.0 or later
  How to use the CD
1. Insert CD into PC’s CD-ROM drive.
  Windows
®:    In a while, Web browser automatically starts. Start up 
window comes up.
  Macintosh
®:    (1) Double-click on the “Projectors” icon appeared on the 
desktop screen.  
(2) When “main.html” file is clicked, Web browser will start 
and Initial window will appear.
2.  Click the model name of your projector first, and then click language yo\
u want  from the displayed list. The User’s manual (detailed) will open.
CAUTION  ►Only use the CD-ROM in a computer CD drive. The CD-
ROM is designed for PC use only. NEVER INSERT THE CD-ROM INTO A 
NON-COMPUTER CD PLAYER! Inserting the CD-ROM into an incompatible 
CD drive may produce a loud noise, which in turn MAY RESULT IN EAR AND 
SPEAKER DAMAGE! 
• After using CD-ROM, please put it into CD case and keep it. Please keep \
the CD neither in direct sunlight nor in a high temperature and high hum\
idity 
environment.
NOTE  • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware \
and 
software of your PC as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,  reproduced or republished without notice to our company. 
						

							16
Specifications
ItemSpecification
Product name Liquid crystal projector
Liquid Crystal Panel 786,432 pixels (1024 horizontal x 768 vertical)
Lens Zoom lens,  f = 19 ~ 23 mm    (approximately)
Lamp 210W UHP
Speaker 16W
Power supply AC 100-120V/3.7A, AC220-240V/1.8A
Power consumption 330W
Temperature range 5 ~ 35°C (Operating)
Size317 (W) x 98 (H) x 288 (D) mm
* Not including protruding parts. Please refer to the following figure\
.
Weight (mass) approx. 3.5kg
<
Ports Computer input port
COMPUTER IN1  
 ....................... D-sub 15 pin mini x1
COMPUTER IN2  
 ....................... D-sub 15 pin mini x1
Computer output port MONITOR OUT  
 ....................... D-sub 15 pin mini x1
Video input port Y, Cb/Pb, Cr/Pr (Component video)  
 ............................................ RCA  x3
S-VIDEO .............. mini DIN 4 pin x1
VIDEO ................................. RCA  x1 Audio input/output port
AUDIO IN1 ............... Stereo mini x1
AUDIO IN2 ............... Stereo mini x1
AUDIO IN3 (R, L) ................ RCA x2
AUDIO OUT (R, L) .............. RCA x2
Others USB ................................. USB-B  x1
CONTROL ................ D-sub 9 pin x1
Optional parts Lamp: 456-8755
Filter set: MU06481
Mounting accessary: HAS-3010 (Bracket for ceiling mount) 
HAS-204L (Fixing adaptor for low ceilings) 
HAS-304H (Fixing adaptor for high ceilings)
Soft case: CA3010
* For more information, please consult your dealer.
317mm
113mm 98mm
288mm 
						

							17
ENGLISH
Troubleshooting - Warranty and after-ser vice
If an abnormal operation (such as smoke, strange odor or excessive soun\
d) 
should occur, stop using the projector immediately. Otherwise if a problem occurs 
with the projector, first refer to the “Troubleshooting” of the “Operating Guide” in 
the CD and run through the suggested checks. 
If this does not resolve the problem, please consult your dealer or serv\
ice 
company. They will tell you what warranty condition is applied.
Please check the following web address where you may find the latest i\
nformation 
for this projector. 
         www.dukcorp.com/av
Trademark acknowledgment
•  Mac
®, Macintosh® and Mac OS® are registered trademarks of Apple Inc.
•  Pentium® is a registered trademark of Intel Corp.
•   Adobe® and Acrobat®, Reader® are registered trademarks of Adobe Systems 
Incorporated.
•  Microsoft
® and Internet explorer®, Windows®, Windows NT®, Windows Vista® 
are registered trademarks of Microsoft Corporation.
•  PowerPC
® is a registered trademark of International Business Machines 
Corporation.
All other trademarks are the properties of their respective owners.
NOTE  • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appea\
r in 
this manual.
• The reproduction, transfer or copy of all or any part of this document i\
s not  permitted without express written consent.