Dukane Imagepro 8915 Lcd Projector Users Manual

							
29

Multifunctional settings
IMAGE Menu
ItemDescription
ASPECT
Using the buttons ▲/▼ switches the mode for aspect ratio. 
At a RGB/DVI signal4:3  16:9  NORMAL   
At a video signal / no signal4:3  16:9  SMALL    
• The NORMAL mode keeps the original aspect ratio of the signal.
•  At a HDTV signal of 1125i (1080i)  or 750p (720p) of COMPONENT 
VIDEO input, this item can't be selected. 
• Performing the automatic adjustment initializes the aspect ratio setting.
OVER SCAN
Using the buttons ▲/▼ adjusts the over-scan ratio.
Large (It reduces picture)  Small (It magnifies picture)
• This item can be selected only at a video signal.
•  When this adjustment is too large, certain degradation may appear 
at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the buttons ▲/▼ adjusts the vertical position.
Up  DownThis item
is not selected when DVI-D input port is selected.
H POSITION
Using the buttons ▲/▼ adjusts the horizontal position.
Left  RightThis item
is not selected when DVI-D input port is selected.
H PHASE
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate 
flicker.
Right  Left
• This item can be selected only at a RGB signal or a component video signal. Note that this does not work with the input signal of 525i(480i)/625i(576i) from the component video port.
With the IMAGE menu, items shown in the table below can 
be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
 MENU [RGB]
 IMAGE PICTURE
   :SELECT
 AUTO ADJUST EXECUTE
 ASPECT         4:3 OVER SCAN      95
 H PHASE        16 H SIZE         1344
 H POSITION     142 V POSITION     25
 SETUP INPUT
 OPTION
 EASY MENU
 SCREEN
 VIDEO Qlty.
 NETWORK 
						

							
30

Multifunctional settings
ItemDescription
H SIZE
Using the buttons ▲/▼ adjusts the horizontal size.
Large  Small
• This item can be selected only at a RGB signal (except DVI-D).
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
pressing the RESET button on the remote control during this 
operation.
AUTO ADJUST 
EXECUTE
Selecting this item performs the automatic adjustment feature.
At a RGB signalThe vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
At a video signalThe video format best suited for the respective input signal will be 
selected automatically.
This function is available only when the AUTO mode is selected to 
the item VIDEO FORMAT of INPUT menu. For a component video 
signal, the signal type is identified automatically independently of 
this function.
• The automatic adjustment operation requires approximately 10 
seconds. Also please note that it may not function correctly with 
some input.
IMAGE Menu (continued) 
						

							
31

Multifunctional settings
VIDEO Qlty. Menu
With the VIDEO Qlty. menu, items shown in the table below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
ItemDescription
PROGRESSIVE
Using the buttons ▲/▼ switches the progressive mode.
TV  FILM  TURN OFF   
• This function performs only at an interlaced signal of a VIDEO 
input, a S-VIDEO input or a COMPONENT VIDEO input of 525i 
(480i) or 625i (576i) signal.  
• When the TV or FILM is selected, the screen image will be crisper. The FILM mode is adaptable to the 2-3 Pull-Down system to the conversion. But these may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, 
please select the TURN OFF, even though the screen image may 
lose the crisp.
3D-YCS
Using the buttons ▲/▼ switches the 3D-YCS mode.
STILL IMAGE
  NORMAL   TURN OFF
• This function performs only at a VIDEO input of NTSC 3.58.
• NORMAL is the mode for images with a lot of motions like movies, 
and STILL IMAGE is the mode for images with few motions or 
completely still ones like slides.
• When this function performs, the VIDEO NR function is ineffective.
VIDEO NR
Using the buttons ▲/▼ switches the noise reduction mode.
HIGH  MIDDLE   LOW
       
• This function performs only at a VIDEO input or a S-VIDEO input. At a VIDEO input of NTSC 3.58, this function performs only when 
the TURN OFF is selected under the 3D-YCS.
• When the HIGH, the MIDDLE or the LOW is selected, the noise on screen is reduced according to each mode.
• When this function is excessive, it may cause a certain degradation of the picture. 
 MENU [RGB]
 IMAGE PICTURE
   :SELECT
 SETUP INPUT
 OPTION
 EASY MENU
 SCREEN
 VIDEO Qlty.
 NETWORK
 PROGRESSIVE  TURN OFF 3D‑YCS       TURN OFF VIDEO NR     LOW 
						

							
32

Multifunctional settings
INPUT Menu
ItemDescription
COLOR SPACE
Using the buttons ▲/▼ switches the mode for color space. 
AUTO 
 RGB  SMPTE240  REC709  REC601      
• This item can be selected only at a RGB signal or a component video signal (except signals of 525i(480i)/625i(576i) from the component video port).
•  The AUTO mode automatically selects the optimum mode. 
• The AUTO operation may not work well at some signals. In such a case, it might be good to select the SMPTE240 or the REC709.
COMPONENT
Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port. 
COMPONENT   SCART RGB 
When the SCART RGB is selected, the COMPONENT VIDEO port 
function as a port for a SCART RGB signal input.  A SCART adapter 
and SCART cable realize a SCART RGB input to the projector. For 
details, ask your dealer.
VIDEO FORMAT
Using the buttons ▲/▼ switches the mode for video format.
AUTO  
  NTSC     PAL    SECAM 
      
N-PAL  M-PAL  NTSC4.43 
• This item performs only at a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type is 
identified automatically independently of this function.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.
DVI
Select a signal source of the DVI-D port using the ▲/▼ buttons.
COMPUTER  DVD
• If unsuitable setting is chosen, brightest or darkest tones may not 
be displayed correctly.
• When you watch the DVD, always choose the “DVD” in spite of the signal source, the computer or the DVD playe r.
With  the  INPUT  menu,  items  shown  in  the  table  below  can 
be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION
 EASY MENU
 SCREEN
   :SELECT
 VIDEO FORMAT AUTO
 COLOR SPACE  AUTO
 INFORMATION
 COMPONENT    COMPONENT
 DVI          DVD VIDEO Qlty.
 NETWORK 
						

							
33

Multifunctional settings
INPUT Menu (continued)
ItemDescription
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATIONRGB1024x768 @60.0FRAME LOCK
INPUT-INFORMATIONS-VIDEOSECAMAUTO
INPUT-INFORMATIONCOMPONENT576i @50SCAR T RGB
• The “FRAME LOCK” message on the dialog means the frame lock function is working. This function automatically works when a RGB signal with vertical frequency of 50 to 60 Hz is input, and it displays 
a moving picture more smoothly. 
• The “SCART RGB” message means the COMPONENT VIDEO 
port is working as a SCART RGB  input port. Please refer  to the item 
COMPONENT in this section.
 (32)
• This item can't be selected at no signal and sync out. 
						

							
34

Multifunctional settings
SETUP Menu
ItemDescription
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL 
 WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL   H:INVERT  V:INVERT  H&V:INVERT 
VOLUMEUsing the buttons ▲/▼ adjusts the volume.
High  Low
STEREOUsing the buttons ▲/▼ selects the internal speaker output mode.
MONO  STEREO
IR REMOTE
Select a remote sensor using the ▲/▼ button (1), then switch it 
using the ► or the ENTER button (2).
(1) 1 : FRONT   2 : TOP       (2)  (Off)   (On)
• 
A sensor cannot be turned off when the other is off.
With the SETUP menu, items shown in the table below can 
be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION
 EASY MENU
 SCREEN
   :SELECT
 WHISPER      NORMAL MIRROR       NORMAL
 STEREO       MONO VOLUME       16
 IR REMOTE    1:  2:
 VIDEO Qlty.
 NETWORK 
						

							
35

Multifunctional settings
SCREEN Menu
ItemDescription
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
SUOMI  POLSKI  TÜRKÇE
ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS  日本語
                 SVENSKA 
MENU POSITIONUsing the buttons ◄/►/▲/▼ adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for 10 seconds.
OSD BRIGHT Using the buttons ▲/▼ switches the 
brightness level of the OSD (On Screen Display).
BRIGHT 
 DARK
BLANK
Using the buttons ▲/▼ switches the mode for the blank screen.
The blank screen is the screen for the temporarily blanking feature 
(21). It is displayed by pressing the BLANK button on the remote control.
MyScreen   ORIGINAL  BLUE  WHITE  BLACK
  
MyScreen is the screen you can register a desired screen. 
ORIGINAL screen is the existing standard screen. BLUE, WHITE 
and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to the BLACK screen after several 
minutes.
• For the MyScreen, please refer to the item MyScreen (36).
With  the  SCREEN  menu,  items  shown  in  the  table  below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button on 
the remote control to progress. Then perform it referring to 
the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION
 EASY MENU
 SCREEN
   :SELECT
 LANGUAGE      ENGLISH MENU POSITION
 START UP      ORIGINAL
 OSD BRIGHT    5
 MyScreen MyScreen Lock TURN OFF MESSAGE       TURN ON
 BLANK         BLACK VIDEO Qlty.
 NETWORK 
						

							
36

Multifunctional settings
ItemDescription
START UP
Using the buttons ▲/▼ switches the mode for the start up screen.The start up screen is the screen displayed when no signal or an unsuitable signal is detected.
MyScreen   ORIGINAL  TURN OFF
    
MyScreen is the screen you can register a desired screen.
ORIGINAL screen is the existing standard screen. When the TURN 
OFF is selected, the BLACK screen is used.
• 
To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to the BLANK screen after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen below. 
About the BLANK screen, please refer to the item BLANK (35).
My Screen
This item functions for capturing the MyScreen of the blank screen and the start up screen. Please execute displaying the input including the picture you want to capture.
1.  Selecting this item displays a dialog titled “MyScreen”. It will ask 
you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the 
ENTER button on the remote control when the picture is display. 
The picture will freeze and the frame for capturing appears.
     To stop performing, press the RESET or ESC button on the 
remote control. 
2.  Using the buttons ◄/►/▲/▼ adjust the frame position. Please 
move the frame to the position of the picture which you want to 
use.
     To start registration, press the ENTER button on the remote 
control.
     To restore the screen and return to the previous dialog, press the  RESET or ESC button on the remote control.
Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen 
registration is finished.” are displayed for several seconds. If the 
registration failed, the message “A capturing error has occurred. 
Please try again.” is displayed.
My Screen Lock
Using the buttons ▲/▼ turns on/off the MyScreen lock function.
TURN ON  TURN OFF
When the TURN ON is selected, the item MyScreen cannot be 
performed. Use this function for protecting the current MyScreen.
SCREEN Menu (continued) 
						

							
37

Multifunctional settings
ItemDescription
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, the following message function 
works. “AUTO IN PROGRESS” while automatically adjusting
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
"Searching….” while searching for the input”Detecting….” while an input signal is detectedThe indication of the input signal by changing The indication of the aspect ration by changing
SCREEN Menu (continued) 
						

							
38

Multifunctional settings
OPTION Menu
ItemDescription
ONE TOUCH
Using the buttons ▲/▼ turns on/off the automatic  keystone correction function.
TURN ON   TURN OFF
You can automatically correct vertical keystone distortion 
corresponding to the angle (forward/backward tilt) at which the unit is set up. This function works with  ONE TOUCH operation.• If the projection screen is inclined, or if the projector is angled downwards, it may not be possible to make the correct adjustment 
when V: INVERT or H&V: INVERT is selected under the MIRROR 
item of the SETUP menu.
• When the zoom adjustment is set to the TELE side, automatic 
correction may be excessive. The automatic correction function 
should be used with zoom set to WIDE whenever possible.
AUTO SEARCH
Using the buttons ▲/▼ turns on/off the automatic signal search function.
TURN ON   TURN OFF
This function works with INPUT, RGB, and VIDEO buttons.
When the TURN ON is selected, detecting no signal automatically 
cycles through input ports in order of following. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image. RGB IN1  RGB IN2  DVI-D  COMPONENT VIDEO  S-VIDEO  VIDEO     
AUTO OFF
Using the buttons ▲/▼ adjusts the time to count down to 
automatically turn the projector off.
Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)
AUT O OFF
ENABLE1
AUT O OFF
DISABLE
0
When the time is set to 0, the projector is not turned off automatically.When the time is set to 1 to 99, and when the passed time with a no-signal or an unsuitable signal reaches at the set time, the 
projector lamp will go off and the power indicator begins blinking. 
Please refer to the section “Turning off the power” (16).
With  the  OPTION  menu,  items  shown  in  the  table  below 
can be performed. 
S e l e c t   a n   i t e m   u s i n g   t h e   c u r s o r   b u t t o n s   ▲ / ▼   o n   t h e 
projector  or  remote  co
ntrol,  and  press  the  cursor  button  ► 
on the projector or remote control, or the ENTER button on 
the  remote  control  to  progress ,  except  for  the  items  LAMP 
TIME  and  FILTER  TIME.  T hen  perform  it  referring  to  the 
following table.
 MENU [RGB]
 VIDEO Qlty.
 SETUP
 PICTURE
 INPUT
 OPTION
 EASY MENU
 SCREEN
   :SELECT
 AUTO OFF      0 LAMP TIME     0
 
 FILTER TIME   0
 ONETOUCH AUTO SEARCH  TURN OFF IMAGE
 NETWORK
 SERVICE