Dukane Imagepro 8761 Portable Projector Users Manual

							Portable Projector
8760/8761
About this users manual
The fastest way to get started is to take your time and do every-
thing right the first time. Take a few minutes now to review the
users manual. This may save you time later on. At the begin-
ning of each section of the manual youll find an overview. If the
section doesnt apply, you can skip it.
User s  M anual 
						

							E-2
Introduction to the Projector
INTRODUCTION
This section introduces you to  your n ew  8760/8761  Projector and
describes the features and controls.
Congratulations on  Your Pu rchase of The  8760/
8761  Projector
The  8760/8761  is one of the  ve ry best projectors  availa ble tod ay. The
8760/8761  enables  you to project precise images up to 500 inches
across (measured diagonally) from your PC or Macintosh computer (desk-
top or notebook), VCR, DVD player, document camera, a laser disc player
or Viewer.
Y ou can use the projector on a tabletop or cart, you can use the projector
to project images from behind the screen, and the projector can be per-
manently mounted on a ceiling*
1.  The remote control can be used wirelessly.
*1Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to en-
sure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector
and the installation must be in accordance with any local building codes.
Please consult your dealer for more information.
Features youll enjoy:
• The newly developed 3D Reform function allows you to correct trap-
ezoidal distortion for both horizontally and vertically so that the im-
age is square even when projector is positioned off center of the
rooms screen.
•   The  8760/8761  projector pr ovides wired and wireless net work ing
When using as a wireless LAN projecto r, no p hysical signal ca ble
connection to a PC is required.*
2
*2  A wireless LAN card is required.   
						

							E-3
INTRODUCTION 
 Introduction to the Projector
•Safety protect by Password and Security functions
Password and Security features prevent the projector from being used
by  unauthorized individuals.
P assword prevents unauthorized individuals from changing projector
settings or adjustments. Security offers complete protection by using
y our PC card as a protect key so that the projector will not project a
signal without insertion of the registered PC card and unauthorized
use can be discouraged.
• The built-in Viewer allows you to start your presentation even when a
PC is not available at the site.
•A  high-bright 220 watt DC lamp.
• The Standby mode reduces standby power consumption significantly.
• The supplied wireless remote control that operates the projector from
the front side or rear.
• The image can be projected between 30 and 500 inches (measured
diagonally).
• The Capture enables you to capture the current projected image.
• An image can be projected from in front or behind a screen, and the
projector can even be installed on the ceiling.
•   Dukane ’s  exclusi ve   intelligent pi xel  blending tech nology-
an  extremely accu rate image compression technology - of fers
a c risp image with UXGA (160 0
 1200) resolution
•   Suppo rts most IBM  V GA, S VGA, XGA , SXGA/UXGA ,
Macintosh, component signal (YCbCr/  YPbPr) or a ny
other RGB signals within a horizontal frequency range of 24 to 100
kHz and a vertical frequency range of 50 to 120 Hz. This includes
NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan-
dard video signals. 
						

							E-4
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
INTRODUCTION 
 Introduction to the Projector 
						

							E-5 •The supplied remote control can be used without a cable, and you
can even use the remote control to operate your PCs mouse wirelessly
from across the room with the built-in remote mouse function.
•You can control the projector with a PC using the PC Control port.
•USB port allows USB mouse operation*
4.
*4The USB ports meet the USB1.1 specification.
•The contemporary cabinet design is light, compact, easy to carry,
and complements any office, boardroom or auditorium.
•Nine pointers are available for your presentation.
INTRODUCTION 
 Introduction to the Projector 
						

							E-6
Part Names of the Projector
SELECTCNACELTERNEEMNUS
O
U
R
C
E
A
U
T
O
 
A
D
J
U
S
TO
N S
T
A
N
D
 B
YSTATUS
POWER LAMPA
L
I
G
N
M
E
N
TPC-CARD
INTRODUCTION 
 Part Names of the Projector
Ventilation (outlet)Heated air is exhausted
from here
*This security slot supports the MicroSaver® Security System.
MicroSaver® is a registered trademark of Kensington Microware Inc.
The logo is trademarked and owned by Kensington Microware Inc.
Built-in Security Slot
(  )*
Adjustable Tilt Foot Lever(See page E-42)
Remote Sensor(See page E-20)
Focus Ring(See page E-43)
Controls(See page E-8)
Ventilation (inlet)
Zoom Lever
(See page E-43)
Carrying Handle
Lens CapLens
Adjustable Tilt  Foot
(See page E-42) 
						

							E-7
INTRODUCTION 
 Part Names of the Projector
Monaural Speaker (2W)
AC InputConnect the supplied power cables three-pin
plug here, and plug the other end into an active
wall outlet.
(See page E-35)Main Power SwitchWhen you plug the supplied power cable into an ac-
tive wall outlet and turn on the Main Power switch,
the POWER indicator turns orange and the projector
is in standby mode.
(See page E-36)
Remote Sensor(See page E-20)
PC Card Slot
Rear Foot
Ventilation(outlet)
Lamp cover screw
Rear Foot
Rotate to make the projector level.
(See page E-43)
PC Card Eject Button
Lamp cover
(See page E-121) 
						

							E-8
INTRODUCTION 
 Part Names of the Projector
910 45 11
678 12 1 32
Top Features
1.POWER Button (ON / STAND BY)
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE: To turn on or off the projector, press and hold this button for a mini-
mum of two seconds.
2. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred, the
lamp cover is not attached properly or the projector has overheated. If
this light remains orange, it indicates that you have pressed a cabinet
key while the Control Panel Key Lock is enabled. See the Status Indi-
cator section on page E-126 for more details.
3. POWER Indicator ( 
 )
When this indicator is green, the projector is on; when this indicator is
orange, it is in standby or idle mode. See the Power Indicator section
on page E-126 for more details. 
						

							E-9
INTRODUCTION 
 Part Names of the Projector 
 Top Features
4. SOURCE Button
Use this button to select a video source such as a PC, VCR, DVD
player, Viewer (PC card), or LAN.
Press and release this button quickly to display the Source List.
Each time this button is pressed for a minimum of ONE second, the
input source will change as follows:
RGB1 → RGB2 → Video → S-Video → Viewer → RGB1 → ...
If no input signal is present, the input will be skipped.
5. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly or take
time to switch between sources.
6. PC CARD Access Indicator
Lights while accessing a PC card.
7. ENTER Button
Executes your menu selection and activates items selected from the
menu.
8. CANCEL Button
Press this button to exit Menus. Press this button to return the adjust-
ments to the last condition while you are in the adjustment or setting
menu.
9. SELECT 
 (+) (–) / Volume Buttons

 : Use these buttons to select the menu of the item you wish to
adjust. When no menus appear, these buttons work as a volume
control. 
						

							E-10  : Use these buttons to change the level of a selected menu item.
A press of the  button executes the selection. When the menus
or the Viewer tool bar is not displayed, these buttons can be
used to select a slide, or to move the cursor in Folder List or
Slide List.
When the pointer is displayed, these 
 buttons move the pointer.
10. MENU Button
Displays the menu.
11. LAMP Indicator
If this light blinks red rapidly, its warning you that the projection lamp
has exceeded 2000 hours (up to 3000 hours in Eco mode) of service.
After this light appears, replace the lamp as soon as possible. (See
page E-121). If this is lit green continually, it indicates that the lamp
mode is set to Eco. See the Lamp Indicator section on page E-127 for
more details.
12. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the keystone
(trapezoidal) distortion, and make the image square.
INTRODUCTION 
 Part Names of the Projector 
 Top Features