Dukane Imagepro 8112 Projector Users Manual

							51
OPTION menu
Item Description
SERVICE
(continued)KEY LOCK
Using the ▲/▼ buttons turns on/off the key lock feature. When ON 
is selected, the buttons on the projector except the STANDBY/ON 
button are locked.
ON 
 OFF
• Please use this function to prevent tampering or accidental 
operation. This function does not have any effect on the remote 
control.
REMOTE FREQ.
(1)  Use the ▲/▼ button to change the projector's remote sensor 
frequency setting (
5).
1:NORMAL 
 2:HIGH
(2)  Use the ◄/► button to change the 
projector's remote sensor on or off.
ON 
 OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be 
on. If the remote control does not function correctly, disable either of 
them (
16).
It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
52) is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer to 
the User's Manual - Network Guide.
(continued on next page) 
						

							52
OPTION menu
Item Description
SERVICE
(continued)
COMMUNICATION
(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE
 
 OFF
NETWORK BRIDGE: 
Select this type, if it is 
required to control an external device as a network 
terminal, via this projector from the computer. 
The CONTROL port doesn't accept RS-232C 
commands.(
Controlling the external device 
via the projector (using the NETWORK BRIDGE 
function) of the User’s Manual - Network Guide)
OFF: Select this mode to receive RS-232C 
commands using the CONTROL port. 
• 
OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSTION METHOD (
below).
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL port.
BAUD RATE
4800bps 
 9600bps 
 19200bps 
 38400bps
      
 PARITY
NONE 
 ODD 
 EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 (above).
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX 
 FULL-DUPLEX
HALF-DUPLEX: This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX: This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• When you select HALF-DUPLEX, check the items,  
RESPONSE LIMIT TIME and BYTES INTERVAL 
TIMEOUT (
53).
(continued on next page) 
						

							53
OPTION menu
Item Description
SERVICE
(continued)
COMMUNICATION
(continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF 
 1s 
 2s 
 3s
    
OFF: Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the 
projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD (
52).
• OFF is selected as the default setting.
BYTES INTERVAL TIMEOUT
Select the blank time length to judge that the 
response data has finished in the communicating 
in the condition of the NETWORK BRIDGE and 
the HALF-DUPLEX through the CONTROL port.
50ms
 
 100ms 
 150ms 
 200ms 
  
• This menu is available only when NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and HALF-DUPLEX is selected for the 
TRANSMISSION METHOD (
52).
• 50ms is selected as the default setting.
(continued on next page) 
						

							54
OPTION menu
Item Description
SERVICE
(continued)INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the INPUT_
INFORMATION box (
65).
FACTORY RESET
Selecting OK using the ► cursor button performs this function. 
By this function, all the items in all of menus will collectively return 
to the initial setting. Note that the LAMP TIME, FILTER TIME, 
LANGUAGE, FILTER MESSAGE, NETWORK, STANDBY MODE, 
SECURITY settings, and others are not reset.
CANCEL 
 OK 
						

							55
NETWORK menu
Remember that incorrect network settings on this 
projector may cause trouble on the network. Be sure 
to consult with your network administrator before 
connecting to an existing access point on your 
network.
Select “NETWORK” from the main menu to access 
the following functions. 
Select an item using the ▲/▼ cursor buttons on the projector or remote control, 
and press the ► cursor button on the projector or remote control, or ENTER 
button on the remote control to execute the item. Then perform it according to the 
following table.
See the User’s Manual - Network Guide for details of NETWORK operation.
NETWORK menu
• If you are not utilizing SNTP (Date/Time Settings of the User’s 
Manual - Network Guide), then you must set the DATE AND TIME during the 
initial installation.
• The network communication control is disabled while the projector is in 
standby mode if the STANDBY MODE item of SETUP menu is set to SAVING. 
Please connect the network communication to the projector after setting the 
STANDBY MODE to NORMAL (
39). NOTE
Item Description
SETUPSelecting this item displays the SETUP 
Menu for the network.
Use the ▲/▼ buttons to select an item, 
and the ► or ENTER button on the remote 
control to perform the item.
DHCP  
(Dynamic Host 
Configuration 
Protocol)Use the ▲/▼ buttons to turn DHCP on/off.
ON 
 OFF
Select OFF when the network does not have 
DHCP enabled.
• When the “DHCP” setting changes to “ON”, it 
takes a little time to obtain IP address from DHCP 
server.
• Auto IP function will be assigned an IP address if 
the projector could not obtain an IP address from 
server even if DHCP is “ON”.
(continued on next page) 
						

							56
NETWORK menu
Item Description
SETUP
(continued)IP ADDRESSUse the ▲/▼/◄/► buttons to enter the IP 
ADDRESS. 
This function can only be used when DHCP is set 
to OFF.
• The IP ADDRESS is the number that identifies 
this projector on the network. You cannot have two 
devices with the same IP ADDRESS on the same 
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET 
MASKUse the ▲/▼/◄/► buttons to enter the same 
SUBNET MASK used by your computer. 
This function can only be used when DHCP is set 
to OFF.
• The SUBNET MASK “0.0.0.0” is prohibited.
DEFAULT 
GATEWAYUse the ▲/▼/◄/► buttons to enter the DEFAULT 
GATEWAY (a node on a computer network that 
serves as an access point to another network) 
address.
This function can only be used when DHCP is set 
to OFF.
DNS SERVERUse the ▲/▼/◄/► buttons to input the DNS 
server address. 
The DNS server is a system to control domain 
names and IP addresses on the Network. 
TIME 
DIFFERENCEUse the ▲/▼ buttons to enter the TIME 
DIFFERENCE. 
Set the same TIME DIFFERENCE as the one 
set on your computer. If unsure, consult your IT 
manager. 
Use the ► button to return to the menu after 
setting the TIME DIFFERENCE.
DATE AND 
TIMEUse the ▲/▼/◄/► buttons to enter the Year (last 
two digits), Month, Date, Hour and Minute.
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled. (
 Date/Time Settings 
of the User’s Manual - Network Guide)
(continued on next page) 
						

							57
NETWORK menu
Item Description
PROJECTOR 
NAME(1)  Use the ▲/▼ buttons on the 
NETWORK menu to select the 
PROJECTOR NAME and press 
the ► button. The PROJECTOR 
NAME dialog will be displayed.
(2)  The current PROJECTOR NAME will be displayed on the first 3 
lines. If not yet written, the lines will be blank.
Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to 
select and enter characters.
To erase 1 character at one time, press the RESET button or 
press the ◄ and INPUT button at the same time. Also if you 
move the cursor to DELETE or ALL CLEAR on screen and 
push the ENTER or INPUT button, 1 character or all characters 
will be erased.The PROJECTOR NAME can be input up to 64 
characters.
(3)  To change an already inserted 
character, press the ▲/▼ button 
to move the cursor to one of the 
first 3 lines, and use the ◄/► 
buttons to move the cursor on the 
character to be changed. After 
pressing the ENTER or INPUT 
button, the character is selected. 
Then, follow the same procedure 
as described at the item (2) above.
(4)  To finish entering text, move the cursor to the OK on screen and 
press the ►, ENTER or INPUT button. To revert to the previous 
PROJECTOR NAME without saving changes, move the cursor 
to the CANCEL on screen and press the ◄, ENTER or INPUT 
button.
(continued on next page) 
						

							58
NETWORK menu
Item Description
MY IMAGESelecting this item displays the MY 
IMAGE menu. 
The application software “PJImage” 
is required to store image(s) into the 
projector.
Use the ▲/▼ buttons to select an item which is a still image by the 
MY IMAGE (
 MY IMAGE (Still Image Transfer) Display of the 
User’s Manual - Network Guide) and the ► or ENTER button to 
display the image.
• The item without image stored cannot be selected.
• The image names are each displayed in 16 characters or less.
To switch the image displayed 
Use the ▲/▼ buttons.
To return to the menu
Press the ◄ button on the remote control.
To erase the image displayed and its source file in the projector.(1)  Press the RESET button on the 
remote control while displaying an 
image to display the MY IMAGE 
DELETE menu. 
(2)  Press the ► button to perform to erase. 
To stop erasing, press the ◄ button.
AMX D.D.
(AMX Device 
Discovery)
Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.
ON 
 OFF
When ON is selected, the projector can be detected by  controllers 
of AMX connected to the same network. For the details of AMX 
Device Discovery, visit the AMX web site.
URL: http://www.amx.com/
(continued on next page) 
						

							59
NETWORK menu
Item Description
INFORMATIONSelecting this item displays the NETWORK_INFORMATION dialog 
for confirming the network settings.
• Only the first 16 characters of the projector neme are displayed.
• Nothing (blank) is shown in the “PROJECTOR NAME” field until 
you setup the item (
57).
• When the voltage level of the battery for the built in clock 
decreases, the set time may become incorrect even though accurate 
date and time are input. Replace the battery suitably
 (69).
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate 
“0.0.0.0” when DHCP is ON and the projector has not gotten 
address from DHCP server.
SERVICEExecuting this item restarts and initializes the network functions. 
Choose the RESTART EXECUTE using the button ►.
Then use the button ► to execute.
Network will be once cut off when choose restart.  
If DHCP is selected on, IP address may be changed. 
After selecting RESTART EXECUTE, NETWORK menu may not be 
controlled approx. 30 seconds. 
						

							60
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter the SECURITY menu
1.  Use the ▲/▼ cursor buttons on the SECURITY menu to select ENTER PASSWORD and press the 
► cursor (or the ENTER) button. The ENTER PASSWORD box will be displayed.  
2.  Use the ▲/▼/◄/► cursor buttons to enter the registered password. 
The factory default password is 5110. This password can be 
changed (
 below). Move the cursor to the right side of the 
ENTER PASSWORD box and press the ► cursor (or the ENTER) 
button to display the SECURITY menu.
• It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box 
will be displayed again. If incorrect password is input 3 times, the 
projector will turn off. Afterwards the projector will turn off every time 
an incorrect password is input.
3.  Items shown in the table below can be performed.
If you have forgotten your password(1)  While the ENTER PASSWORD box is displayed, press and hold the 
RESET (or press the ► cursor and the INPUT buttons at the same 
time) button for about 3 seconds.
(2)  The 10 digit Inquiring Code will be displayed. Contact your dealer 
with the 10 digit Inquiring Code. Your password will be sent after 
your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1).  
Item Description
SECURITY 
PASSWORD 
CHANGE
(1)  Use the ▲/▼ cursor buttons on the 
SECURITY menu to select SECURITY 
PASSWORD CHANGE and press the ► 
cursor (or the ENTER) button to display the 
ENTER NEW PASSWORD box.
(2)  Use the ▲/▼/◄/► cursor buttons to enter the new password.
(3)  Move the cursor to the right side of the 
ENTER NEW PASSWORD box and press the 
► cursor (or the ENTER) button to display 
the NEW PASSWORD AGAIN box, enter the 
same password again. 
(4)  
Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
cursor 
(or the ENTER) button and the NOTE 
NEW PASSWORD box will be displayed for 
about 30 seconds, please make note of the 
password during this time.
Pressing the ► cursor (or the ENTER) button will close the NOTE NEW 
PASSWORD box.
• Please do not forget your password.
SECURITY menu
(continued on next page)