Dukane 8755D Projector User Manual

							
59
Network Functions
Network Functions
Configuring and Controlling the Projector via a Web Browser
You can change the settings of or control the projector via a network by using a 
web browser from a PC that is connected to the same network.
(
4)
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when 
the projector requires maintenance or has encountered an error.
(
25)
Projector Management via SNMP
This projector is SNMP (Simple Network Management Protocol) compliant, 
allowing you to monitor it from a remote location using SNMP software. In 
addition, the projector is able to send failure & warning alerts to a specified PC.
(
27)
Controlling the Projector via Scheduling
You can schedule the projector to perform various functions according to the 
DATE and TIME.
(
28)
Still Image Transfer
The projector can display still images that are transferred via the network.
(
31)
Projector Control via RS-232C via the Network
The projector can be controlled using RS-232C commands over a network.
(
33)
This projector is equipped with the following network functions.
8755D-RJ only 
						

							
60
Network Functions Notes: 
						

							
61
Network Functions
Before using the network functions…
To use the network functions of this projector, the projector must be configured to 
suit your network. Consult with your network administrator before connecting the 
projector to your network. Incorrect network configuration of this projector may 
cause problems on your network.
Connect to the Gateway (The router/PC that forwards traffic to a destination 
outside of the subnet of the transmitting device) from the network terminal on the 
projector using a CAT-5 cable and configure the following settings.
If  using a network with DHCP enabled:
The projector’s network settings can be configured automatically. when [DHCP] 
on the network menu is set to [TURN ON]. Please refer to DHCP in network 
menu. (
User's Manual - Operating Guide : NETWORK Menu ) If a fixed / static IP 
address is required, please configure your projector according to the steps in the  following section.
If  using a network system that does not have DHCP enabled or if  
using a fixed IP address on a network system equipped with DHCP 
enabled:
Configure the following settings on the network menu.   
(
User's Manual - Operating Guide : NETWORK Menu )
1. [DHCP]: Disable DHCP (Set [DHCP] to [TURN OFF]).
2. [IP ADDRESS]: Enter an appropriate IP address for the projector to connect 
to your network.
3. [SUBNET MASK]: Enter an appropriate SUBNETMASK for the projector to 
connect to your network.
4.  [DEFAULT GATEWAY]: Enter an appropriate Gateway (the router/PC that 
forwards traffic to a destination outside of the subnet of the transmitting 
device) address for the projector to connect to your network. 
						

							
62
Configuring and controlling the projector via a web browser 
						

							
63
Network Functions
When configuring or controlling the projector via a web browser, an ID and 
password are required. There are two types of IDs, Administrator IDs and User 
IDs. The following chart describes the differences between user and administrator 
IDs.
Below are the factory default settings for administrator IDs, user IDs and 
passwords.
ItemDescriptionAdministrator IDUser ID
Network InformationDisplays the projector’s current 
network configuration settings.√√
Network SettingsDisplays and configures network settings.√N/A
Port SettingsDisplays and configures communication port settings. √N/A
Mail SettingsDisplays and configures e-mail addressing settings.√N/A
Alert SettingsDisplays and configures failure & warning alerts.√N/A
Schedule SettingsDisplays and configures schedule settings.√N/A
Date/Time Settings Displays and configures the date and 
time settings.√N/A
Security SettingsDisplays and configures passwords and other security settings.√N/A
Projector Control
Controls the projector.√√
Projector StatusDisplays and configures the current projector status.√√
Network RestartRestarts the projector’s network connection.√N/A
ItemIDPassword
Administrator IDAdministrator
User IDUser
Configuring and controlling the projector via a web browser (Continued) 
						

							
64
Settings
Settings
Refer to the following for configuring or controlling the projector via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1)  Enter
 
[https://192.168.1.10] into the 
address bar of the web browser and 
the screen in Fig. 1 will be displayed.
2)  Enter your ID and password and click 
[Logon].
If the logon is successful either the Fig.2 or Fig.3 screen will be displayed.
3)  Click the desired operation or configuration item on the main menu located on 
the left-hand side of the screen (Fig. 2 or Fig. 3).
Fig. 2 (Logon with administrator ID)Fig. 3 (Logon with user ID)
Fig. 1 
						

							
65
Settings
Network Information
All screen images displayed in this manual are 
screens of a logon using an administrator ID.
Any administrator only functions will not be 
displayed when using a user ID. Refer to the 
descriptions in each table.
Displays the projector’s current network configuration settings.
ItemDescription
DHCPDisplays the DHCP configuration settings.
IP Address Displays the current IP address.
Subnet MaskDisplays the Subnet Mask.
Default GatewayDisplays the Default Gateway.
MAC Address
Displays the MAC address.
Firmware Date Displays the network firmware time stamp. This information is only displayed when logged on using an administrator ID.
Firmware Version Displays the network firmware version number. This information is 
only displayed when logged on using an administrator ID. 
						

							
66
Settings
Network Settings
Displays and configures network settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses. NOTE
ItemDescription
IP Configuration Configures network settings.
DHCP ONEnables DHCP.
DHCP OFF Disables DHCP.
IP AddressConfigures the IP address when DHCP is disabled.
Subnet MaskConfigures the Subnet Mask when DHCP is disabled.
Default GatewayConfigures the Default Gateway when DHCP is disabled.
Projector Name Configures the Projector name.
SysLocationConfigures the location to be referred to when using SNMP.
SysContactConfigures the contact information to be referred to when 
using SNMP. 
						

							
67
Settings
Port Settings
Displays and configures communication port settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. The network connection must be restarted when the 
configuration settings are changed. The network connection can be restarted 
using [Network Restart] on the main menu.dresses.
NOTE
ItemDescription
Network Control Port1 (Port:23)
Configures command control port 1 (Port:23).
Port openClick the [Enable] check box to use port 23.
AuthenticationClick the [Enable] check box when authentication is required for this port.
Network Control Port2 (Port:9715)Configures command control port 2 (Port:9715).
Port openClick the [Enable] check box to use port 9715.
AuthenticationClick the [Enable] check box when authentication is required for this port.
Image Transfer Port (Port:9716)Configures the image transfer port (Port:9716).
Port openClick the [Enable] check box to use port 9716.
AuthenticationClick the [Enable] check box when authentication is required for this port.
SNMP Port
Configures the SNMP port.
Port openClick the [Enable] check box to use SNMP.
Trap address Configures the destination of the SNMP Trap in IP format.
SMTP Port Configures the SMTP port.
Port openClick the [Enable] check box to use the e-mail function. 
						

							
68
Settings
Mail Settings
Displays and configures e-mail addressing settings.
Click the [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses. NOTE
ItemDescription
Send MailClick the [Enable] check box to use the e-mail function. 
Configure the conditions for sending email under [Alert Settings].
SMTP Server IP Address Configures the address of the mail server in IP format.
Sender E-mail addressConfigures the sender e-mail address.The length of the sender e-mail address can be up to 255 alphanumeric characters.
Recipient E-mail addressConfigures the e-mail address of up to five recipients. You can also specify 
[TO] or [CC] for each address. The length of the recipient e-mail address can be up to 255 alphanumeric characters.