Dukane 8755D Projector User Manual

							
29

Multifunctional settings
ItemDescription
PROGRESSIVE
Using the buttons ▲/▼ switches the progress mode.
TV  FILM  TURN OFF
• This function is performed only for an interlaced signal of a VIDEO 
input, an S-VIDEO input or CONPONENT VODEO input of 525i 
(480i) or 625i (576i) signal.
• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select TURN OFF, 
even though the screen image may lose the sharpness.
MY MEMORY Selecting a mode of MY MEMORY using the buttons ▲/▼ and then 
pressing the button ► or the ENTER button performs each function.
LOAD1  LOAD2  LOAD3  LOAD4
SAVE4 
 SAVE3  SAVE2  SAVE1
This projector has 4 numbered memories for adjustment data.  Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds to the c
ommand’s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 saves the current adjustment data on the memory whose number corresponds to the 
command’s number. 
• The current adjustment data of the items in the PICTURE menu is 
stored, except for the adjustment data in the CUSTOM modes for 
the GAMMA and COLOR TEMP items.
•  There may be some noise and/or the screen may flicker for a 
moment when data is loaded to memory. This is not a malfunction.
PICTURE Menu (continued) 
						

							
30

Multifunctional settings
IMAGE Menu
ItemDescription
ASPECT
Using the buttons ▲/▼ switches the mode for aspect ratio. 
For an RGB signal4:3  16:9  NORMAL   
For a video signal / no signal4:3  16:9  SMALL    
• The NORMAL mode keeps the original aspect ratio of the signal.• For an HDTV signal of 1125i (1080i) or 750p (720p) as the 
COMPONENT VIDEO input, this item can't be selected. 
OVER SCAN
Using the buttons ▲/▼ adjusts the over-scan ratio.
Large (It reduces picture)   Small (It magnifies picture)
• This item can be selected only for a video signal.
•  When this adjustment is too large, certain degradation may appear 
at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the buttons ▲/▼ adjusts the vertical position.
Up  Down• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the 
default setting. Pressing the RESET button when V POSITION is 
selected will reset the V POSITION to the default setting.
H POSITION
Using the buttons ▲/▼ adjusts the horizontal position.
Left  Right• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to 
the default setting. Pressing the RESET button when H POSITION 
is selected will reset the H POSITION to the default setting.
H PHASE
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate 
flicker.
Right  Left
• This item can be selected only for an RGB signal or a component video signal. Note that this does not work with the input signal of 
525i(480i)/625i(576i)/SCART RGB from the component video port.
With the IMAGE menu, items shown in the table below can 
be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
 MENU [RGB]
 IMAGE PICTURE
   :SELECT
 AUTO ADJUST EXECUTE
 ASPECT         4:3 OVER SCAN      5
 H PHASE        16 H SIZE         1344
 H POSITION     142 V POSITION     25 SETUP INPUT
 OPTION EASY MENU
 SCREEN 
						

							
31

Multifunctional settings
ItemDescription
H SIZE
Using the buttons ▲/▼ adjusts the horizontal size.
Large  Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the RESET button on the remote control during this 
operation.
AUTO ADJUST 
EXECUTE
Selecting this item performs the automatic adjustment feature.
For an RGB signalThe vertical position, the horizontal position, the clock phase and 
the horizontal size will be automatically adjusted. And the aspect 
ratio will be automatically selected. Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal or s-video signalThe video format best suited for the respective input signal will be 
selected automatically.
This function is available only when the AUTO mode is selected to 
the VIDEO FORMAT item in the INPUT menu. For a component 
video signal, the signal type is identified automatically independently 
of this function.For a video signal, s-video signal or component video signalThe vertical position and horizontal position will be automatically adjusted.
For a component video signalThe aspect ratio will be automatically selected.The clock phase will be automatically adjusted.
• The automatic adjustment operation requires approximately 10 
seconds. Also please note that it may not function correctly with 
some input.
IMAGE Menu (continued) 
						

							
32

Multifunctional settings
INPUT Menu

ItemDescription
COLOR SPACE
Using the buttons ▲/▼ switches the mode for color space. 
AUTO 
 RGB  SMPTE240  REC709  REC601      
• This item can be selected only for an RGB signal or a component video signal (except signals of 525i(480i)/625i(576i)/SCART RGB from the component video port).
•  The AUTO mode automatically selects the optimum mode. 
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
COMPONENT
Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port. 
COMPONENT   SCART RGB 
When the SCART RGB is selected, the COMPONENT VIDEO port 
function as a port for a SCART RGB signal input.  A SCART adapter 
and SCART cable realize a SCART RGB input to the projector. For 
details, contact your dealer.
VIDEO FORMAT
Using the buttons ▲/▼ switches the mode for video format.
AUTO  
  NTSC     PAL    SECAM 
      
N-PAL  M-PAL  NTSC4.43 
• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type 
is identified automatically independently of this function.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.
FRAME LOCK
Using the buttons ▲/▼ turns the frame lock function on/off. 
TURN ON  TURN OFF
• This item performs only at a RGB signal with vertical frequency of 50 to 72 Hz for the model TBD, or 50 to 60 Hz for the model 
8755D.
• When the TURN ON is selected, a moving picture is displayed 
more smoothly.
• This function may cause a certain degradation of the picture. In 
such a case, please select the TURN OFF.
With  the INPUT   menu,  the  items  shown  in  the  table  below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION EASY MENU
 SCREEN
   :SELECT
 VIDEO FORMAT AUTO
 COLOR SPACE  AUTO
 FRAME LOCK INFORMATION
 COMPONENT    COMPONENT
TURN ON 
						

							
33

Multifunctional settings
INPUT Menu (continued)
ItemDescription
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATIONRGB1024x768 @60.0FRAME LOCK
INPUT-INFORMATIONS-VIDEOSECAMAUTO
INPUT-INFORMATIONCOMPONENT576i @50SCAR T RGB
• The “FRAME LOCK” message on the dialog means the frame lock function is working. This function automatically works when a RGB signal with vertical frequency of 50 to 60 Hz is input, and it displays 
a moving picture more smoothly. 
• The “SCART RGB” message means the COMPONENT VIDEO 
port is working as a SCART RGB input port. Please refer to the 
COMPONENT item in this menu.
 (32)
• This item can't be selected for no signal and sync out. 
						

							
34

Multifunctional settings
SETUP Menu
ItemDescription
KEYSTONE
Using the buttons ▲/▼ corrects the keystone distortion.
Upper in the data  Lower in the data
•  The adjustable range of this function will vary with the type of input 
signal. At some signals, this function may not work well.
• When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is 
angled downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE side, this correction 
may be excessive. This function should be used with zoom set to 
WIDE whenever possible.
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL 
 WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL   H:INVERT  V:INVERT  H&V:INVERT 
VOLUMEUsing the buttons ▲/▼ adjusts the volume.
High  Low
AUDIO
Choose an input port using the buttons ▲/▼ 
(1), then select the audio port to be interlocked 
with the input port using the buttons ◄/► (2). 
When off is selected, both of two audio ports 
do not work for the input port.
(1)  RGB1  RGB2   COMPONENT  S-VIDEO  VIDEO
(2)  1  2  
With the SETUP
 menu, the items shown in the table below 
can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION EASY MENU
 SCREEN
   :SELECT
 WHISPER      NORMAL MIRROR       NORMAL
 KEYSTONE     +0
 AUDIO  VOLUME       16
 AUDIO
  
 RGB2
   QUIT
 RGB1
 S‑VIDEO VIDEO
 COMPONENT
1   2 
						

							
35

Multifunctional settings
SCREEN Menu
ItemDescription
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
SUOMI  POLSKI  TÜRKÇE
ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS  日本語
                 SVENSKA 
MENU POSITIONUsing the buttons ◄/►/▲/▼ adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for 10 seconds.
OSD BRIGHT. Using the buttons ▲/▼ switches the 
brightness level of the OSD (On 
Screen Display).
BRIGHT 
 DARK
BLANK
Using the buttons ▲/▼ switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature 
(22). It is displayed by pressing the BLANK button on the remote control.
MyScreen   ORIGINAL  BLUE  WHITE  BLACK
  
MyScreen is a screen you can register as a desired screen. The 
ORIGINAL screen is the existing standard screen. BLUE, WHITE 
and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to the BLACK screen after several 
minutes.
• For the MyScreen, please refer to the MyScreen item (36).
With  the S CREEN   menu,  the  items  shown  in  the  table 
below can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
 MENU [RGB]
 IMAGE
 SETUP
 PICTURE
 INPUT
 OPTION EASY MENU
 SCREEN
   :SELECT
 LANGUAGE      ENGLISH MENU POSITION
 START UP      ORIGINAL
 OSD BRIGHT.   5
 MyScreen MyScreen Lock TURN OFF MESSAGE       TURN ON
 BLANK         BLACK 
						

							
36

Multifunctional settings
ItemDescription
START UP
Using the buttons ▲/▼ switches the mode for the start-up screen.The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.
MyScreen   ORIGINAL  TURN OFF
    
MyScreen is a screen you can register as a desired screen.The 
ORIGINAL screen is the existing standard screen. When TURN 
OFF is selected, the BLACK screen is used.
• 
To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to the BLANK screen after several 
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen below. For 
the BLANK screen, please refer to the BLANK item (35).
MyScreen
This item functions for capturing the MyScreen of the blank screen and the start-up screen. Please execute displaying the input including the picture you want to capture.
1.  Selecting this item displays a dialog titled “MyScreen”. It will ask 
you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is 
displayed. The picture will freeze and the frame for capturing 
appears.
     To stop performing, press the RESET or ESC button on the 
remote control. 
2.  Using the buttons ◄/►/▲/▼ adjusts the frame position. Please 
move the frame to the position of the picture which you want to use.      The frame may not be able to be moved for some input signals.
     To start registration, press the ENTER button on the remote 
control.
     To restore the screen and return to the previous dialog, press the  RESET or ESC button on the remote control.
Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen 
registration is finished.” are displayed for several seconds. If the 
registration failed, the message “A capturing error has occurred. 
Please try again.” is displayed.
MyScreen Lock
Using the buttons ▲/▼ turns on/off the MyScreen lock function.
TURN ON  TURN OFF
When the TURN ON is selected, the item MyScreen is locked. Use 
this function for protecting the current MyScreen.
SCREEN Menu (continued) 
						

							
37

Multifunctional settings
ItemDescription
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, the following message function 
works. “AUTO IN PROGRESS” while automatically adjusting
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
"Searching….” while searching for the input”Detecting….” while an input signal is detectedThe indication of the input signal displayed by changing The indication of the aspect ration displayed by changingThe indication of "FREEZE" and "II" while freezing the screen by pressing the FREEZE button.• When the TURN OFF is selected, please remember if the picture is freezing. Do not mistake freezing for a malfurction (22).
SCREEN Menu (continued) 
						

							
38

Multifunctional settings
OPTION Menu
ItemDescription
AUTO SEARCH
Using the buttons ▲/▼  turns on/off the automatic signal search  function.
TURN ON  TURN OFF
This function works with INPUT, RGB, and VIDEO buttons.
When the TURN ON is selected, detecting no signal automatically 
cycles through input ports in the following order . The search is started from the current port. Then when an input is found, the projector will stop searching and display the image. RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO     
• When the RGB IN2/RGB OUT port functions as an RGB out port (the 
RGB IN OUT switch is pushed in), RGB IN2 cannot be selected. In 
that case “RGB2/RGB OUT 
  RGB OUT” message will be displayed.
AUTO OFF
Using the buttons ▲/▼ adjusts the time to count down to 
automatically turn the projector off.
Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)
AUT O OFF
ENABLE1
AUT O OFF
DISABLE
0
When the time is set to 0, the projector is not turned off automatically.When the time is set to 1 to 99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the projector 
lamp will go off and the power indicator begins blinking. Please 
refer to the section “Turning off the power” (17).
LAMP TIME
The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the lamp.
Pressing the RESET button on the remote control or the button ► of the projector displays a dialog.  To reset the lamp time, select the 
RESET using the button ▲.
RESET 
 CANCEL
• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.• For the lamp replacement, see the section "Lamp" (40, 41).
FILTER TIME
The filter time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the air filter.Pressing the RESET button on the remote control or the button ► of the projector 
displays a dialog. To reset the filter time, select the RESET using the button ▲.
RESET  CANCEL
• Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section "Air filter" (42).
With  the 
OPTION
  menu,  the  items  shown  in  the  table  below  can be performed. 
Select  an  item  using  the  cursor  buttons  ▲/▼  on  the  projector  or 
remote  co ntrol, and  press  the  cursor  button  ►  on  the  projector 
or  remote  control,  or  the  ENTER  button  on  the  remote  control  to 
execute  the  item , except  for  the  items  LAMP  TIME  and  FILTER 
TIME. Then perform it referring to the following table.
 MENU [RGB]
 PICTURE
   :SELECT
 
 IMAGE
 SETUP INPUT
 OPTION EASY MENU
 SCREEN
 AUTO OFF      0min LAMP TIME     0h FILTER TIME   0h
 AUTO SEARCH  TURN OFF
 SERVICE