Dream Vision Inti+ User Manual

6.0  MENU AND PICTURE SETTING
R699810 - Inti+ Series User Manual 31 
6.4.0.2 Adjust Area
Whole: the entire screen is selected for adjustment.
Zone: the screen is divided into 121 adjustment zones.
6.4.0.3 Adjust Color
Select the color to adjust: Red or Blue.
6.4.0.4 Adjust Pattern Color
Select a pattern to help the pixel alignment. Settings: White or Green+adjust Color.
6.4.0.5 Adjust (Pixel)
This function is enable when the Adjust Area is set to Zone only. You can adjust the
selected color position...

6.0  MENU AND PICTURE SETTING
32R699810 - Inti+ Series User Manual
stretched to completely fill the panels without black bands, using the optimum resolution and brightness.
Anamorphic Mode A.
•ModeB: This setting squeezes horizontally the picture to fit a 16:9 image into cinemascope screen. This setting
is to be used with an anamorphic installation where the lens is permanently fixed in front of the unit and to watch
16:9 content in its original format.
Anamorphic Mode B.
Screen Adjust
This setting...

6.0  MENU AND PICTURE SETTING
R699810 - Inti+ Series User Manual 33 
Menu Display
15sec: Display menu for 15 seconds before fade out.
On: Always display menu.
Line Display
5sec: Display the input settings for 5 seconds after input selection.
Off: Don’t display.
Source Display
On: Display the source of the input signals after input selection.
Off: Don’t display.
Logo
On: Display logo during startup for 5 seconds.
Off: Don’t display.
Language
Choose the OSD language between: English, Japanese, German,...

6.0  MENU AND PICTURE SETTING
34R699810 - Inti+ Series User Manual
Displays the type of the current video input signal. If PC input is selected, this item cannot be displayed.
Deep Color Depth
Display the bit depth (color depth) of the video signals input from the HDMI\
 terminals. Deep Color is not displayed
for YCbCr 4:2:2 signals.
Resolution
If the active input is PC input., its resolution is displayed.
H. Frequency
In the case of PC signal, the horizontal frequency is displayed.
V.  Frequency
In the...

7.0  ANAMORPHIC SETUPS
R699810 - Inti+ Series User Manual 35 
7.0 ANAMORPHIC SETUPS
7.1 Lens Zoom and Theatre System Kit
The Inti+ Series centralizes the controls and automation commands for the Theatre System Kit for a unique,
versatile and unexpectedly simple to operate 2.35:1 theatre experience using an anamorphic Lens.
• Integrated Constant Image Width (CIW) scaler for 2D content.
• Dedicated commands to control the lens position or picture size on a 2.35:1 screen.
7.2 Using the Remote Control...

7.0  ANAMORPHIC SETUPS
36R699810 - Inti+ Series User Manual
7.3 Installing a Motorized Anamorphic Lens
Plug the 12V Trigger output of the projector to the Anamorphic motorization
Connect the lens motorization to the 12V Trigger output 
Configure into Function “Menu ⇒⇒ ⇒
⇒ T rigger ⇒⇒
⇒
⇒ On (Anamo)”
The “Function  ⇒⇒
⇒
⇒  Tr igger” menu determines the 12V Trigger output located in the panel input at the rear of this unit.
This is a global parameter (for all inputs):
• Off: the 12V Trigger is always...

8.0  MAINTENANCE
R699810 - Inti+ Series User Manual 37 
8.0 MAINTENANCE
8.1 Clean Dirt on the Cabinet
Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and
wipe, followed by wiping again using a dry cloth.
Caution
Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come
off.
• Do not wipe with a stiff cloth.
• Do not wipe with force.
• Do not wipe with thinner or benzene.
• Do not spray...

8.0  MAINTENANCE
38R699810 - Inti+ Series User Manual
•Loosen the screw on the lamp trap at the rear of this unit.
• Open the lamp Cover and loosen the 2 screws on the lamp unit to release it.
• Pull out the lamp unit using the handle.
• Insert the new lamp unit until it is firmly in place.
• Tighten the screws of the lamp unit.
• Attach the lamp cover and fasten the lamp trap screw.
Resetting Lamp Time
After installing a new lamp, reset the lamp time using the OSD menu.
a) Turn On the unit.
b) Browse...

8.0  MAINTENANCE
R699810 - Inti+ Series User Manual 39 
8.5 Troubleshooting
Warning Messages Led
ID#
Operating LED
DescriptionSTANDBY / 
ONLAMP
orange LEDW ARNING
red LEDBlinking
1red---Unit is in standby mode
2g reen---Unit is in operate mode (during projection)
3blinking 
g reen--Ye s
Unit is in operate mode, but HIDE is ON. 
Press again on HIDE button to obtain a 
picture.
4blinking red--Ye sUnit is in cooldown mode. (switching off)
5/6-orange--
Lamp time has reached 2900 hours and/or 
prepare to...

9.0  MISCELLANEOUS
40R699810 - Inti+ Series User Manual
9.0 MISCELLANEOUS
9.1 RS-232C protocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable (female
- female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specifications for this unit are as follows:
RS-232C pin assignation
Command Format
When sending a command to this unit, use the following data format:
CAUTION
When in Cool Down mode, do not pull out...