Dream Vision Inti+ User Manual

2.0  INSTALLATION GUIDELINES
R699810 - Inti+ Series User Manual 11 
Precautions for Ceiling-mount
•To ceiling-mount this unit, special expertise and techniques are
necessary. Be sure to ask your dealer or specialist to perform
mounting.
• Do not mount at places that may be subjected to vibration and
shock.
• Depth of the screw holes (A) is 23 mm. Use at least 13mm long
screws but not longer than 23mm as you may damage inside
the projector.
• Install at a safe place in case this unit or a part of it may...

2.0  INSTALLATION GUIDELINES
12R699810 - Inti+ Series User Manual
brain will interpret the 3D-projection as two superposed pictures.
In general the perception of the 3D effect will vary according to your seat position and to the screen size. When a
movie is produced for 3D projection, the director knows at witch distance the effect will be perceived and witch
depth he intends to gives to the objects. In general, the recommended distance is three times the height of the
screen to obtain the best...

2.0  INSTALLATION GUIDELINES
R699810 - Inti+ Series User Manual 13 
•To avoid the use of keystone correction, and only use the vertical and horizontal shifts, make sure to not exceed
the values contained in the tab below: 
2.9.0.1 Adjust the picture position
The Inti+ Series projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control]
setting into the [Installation] menu, select the shift adjustment. Or use the direct access button on the Remote
Control Unit [Lens...

3.0  REMOTE CONTROL UNIT (RCU)
14R699810 - Inti+ Series User Manual
3.0 REMOTE CONTROL UNIT (RCU)
3.1 General View
3.2 Loading and replacing batteries
•Push the cover tab with the fingernail a little backwards and pull upwards the cover top. Slide the cover forward
to remove.
• Push the battery body towards the spring and lift up to remove. Insert two AAA size batteries, making sure the
polarities match the + and - marks inside the battery compartment.
• Insert the lower tab of the battery cover in the...

3.0  REMOTE CONTROL UNIT (RCU)
R699810 - Inti+ Series User Manual 15 
3.3 How to use the Remote Control Unit
The operable distance of the remote control unit is about 7m for direct reception and within 30 degree angle with
respect to the sensor.
CAUTION WHEN USING BATTERIES
Do not mix new and old batteries.Do not mix different type of batteries as they are different in characteristics. Insert
batteries according to the + and - marks on the battery case. Do not put batteries into fire or recharge them if...

4.0  GETTING STARTED
16R699810 - Inti+ Series User Manual
4.0 GETTING STARTED
4.1 General View
Front side
•Optical Lens & Lens cover. The lens cover is motorized on Inti+2 & +3.
• Operating LEDs: see section 4.3, page 17 for more details.
• Air Outlets: see “Air-Flow and Space Requirements”,  page 10.
Rear side
•Input Panel: connect your video source to the correct input.
• Operating and Navigation buttons described in section 4.4, page 18.
• Main Power: connect the power cord as shown below.
• Lamp...

4.0  GETTING STARTED
R699810 - Inti+ Series User Manual 17 
4.2 Connecting the Power Cord
•Before plugging in the Power Cord, ensure that all devices have been connected
to their respective inputs to this unit.
• Connect the power cord to the power input terminal of the projector.
4.3 Operating LEDs
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
Do not use a power voltage different from that which is indicated....

4.0  GETTING STARTED
18R699810 - Inti+ Series User Manual
4.4 Operating and Navigation Buttons
ButtonDescription
Power buttonTo turn On or Off the projector.
Input sourceTo switch input source.
OK (Enter)To select or to confirm action.
Up - down - left - rightTo navigate into On Screen Display (OSD) Menu.
MenuTo display On Screen Display (OSD) Menu.
BackTo return to previous menu or cancel action.
STANDBY/ON
INPUT
OK
MENU BACK
Power button
Up - down OK
Input source
Back
Menu
Left - right 

5.0  CONNECTIONS
R699810 - Inti+ Series User Manual 19 
5.0 CONNECTIONS
5.1 Caution when connecting a device to HDMI input
5.2 Connecting a Video Source to the Projector
Prior to connecting any device to this unit, switch the projector in standby mode. Never connect a HDMI
source to this unit when the projector is in operate mode. The HDMI termination is a self-powered
connection and can cause electric discharges.
ConnectionDevice
HDMI1, HDMI2
v1.4a with M3 lock holeHDMI or DVI-D sources: Blu-Ray Disc...

5.0  CONNECTIONS
20R699810 - Inti+ Series User Manual
For input resolution and refresh rates, check the “Compatible resolutions”,  page 47.
5.3 Connecting an Automation or Control device
Make sure to use a certified HDMI cable, especially when the distance between the different devices are
longer than 5 meters. If it is the case, the use of a split system or optical fiber cable is highly recommended.
ConnectionDevice
RS-232C (*)A utomation Device, Control Device or Computer with RS-232 capability....