Dolmar Lawn Mower Rm 72 13 H German Version Manual

SAFETY DECALS
Your machine must be used with care. Therefore, decals have been placed on the
machine, to remind you pictorially of the main precautions to take during use.
These decals are to be considered an integral part of the machine.
If a decal should fall off or become illegible, contact your retailer to replace it.
Their meaning is explained below.
EN 6SAFETY
Warning:Read Operator’s Man-
ual before operating this
machine.
Warning:Disconnect the igni-
tion key and read the instruc-
tions before...

2. IDENTIFICATION OF THE MACHINE AND PARTS
IDENTIFICATION OF THE MACHINE
The plate located under the driver’s seat
has the essential data and serial number
of each machine (7).
This number must be quoted when you
require technical assistance or spare
parts.
1.Acoustic power level according to
directive 2000/14/CE
2.Conformity mark according to direc-
tive 98/37/EEC
3.Year of manufacture
4.Nominal power (if indicated)
5.Operating engine speed in r.p.m
6.Type of machine
7.Serial number
8.Weight in kgs...

13. Collector channel:this is the part connecting the cutting deck to the grass-
catcher.
14. Grass-catcher:as well as collecting the grass cuttings, this is also a safety
element in that it stops any objects drawn up by the blade from being thrown
outside of the machine.
15. Stone-guard or deflector:this can be fitted in place of the grass-catcher
and prevents objects drawn up by the blade from being thrown outside of the
machine.
16. Engine:this moves the blade and drives the wheels. It is fully...

3. UNPACKING AND ASSEMBLY
For storage and transport reasons, some components of the machine are not
directly installed in the factory, but have to be assembled after their removal from
the packing. Final assembly is carried out by following these simple instructions.
For transport reasons the machine is supplied without engine
oil or fuel. Before starting up the engine, fill with oil and fuel following the
instructions given in the engine booklet.
UNPACKING
When unpacking the machine, take care to gather...

Push the pin in using a hammer, ensuring that it comes completely through to the
opposite side.
To avoid damaging the steering wheel with the hammer, use
an awl or a screw-driver of the same size as the pin to push it in the last part.
FITTING THE  SEAT
Fit the seat (1) onto the plate (2) using the
screws (3).
CONNECTING THE  BATTERY
The battery (1) is situated in a compart-
ment under the steering wheel and is
reached by removing the plastic cover (2)
held on by two screws (3).
Connect the two red...

To prevent the safety device in the electronics card from cut-
ting in, never start the engine until the battery is fully charged!
Follow the battery manufacturers instructions regarding
safe handling and disposal.
FITTING THE  GRASS-CATCHER
First of all assemble the frame, joining the upper part (1), including the opening,
to the lower part (2), using the supplied nuts and screws (3) and following the
indicated sequence.
Position the angle supports (4) and (5), respecting the right (R
) and left (L
)...

Hook all the plastic profiles to the frame
tubes with the help of a screwdriver (7).
Insert the handle (8) into the holes of the
canvas (9). Attach this to the frame using
the screws (10), following the indicated
sequence, and complete the assembly
screwing the four front and rear self-
threading screws (11).
Lastly, fit the stiffening bar (12) on the out-
side of the frame base, keeping the flat part towards the canvas and using the
nuts and screws supplied (13) in the sequence indicated.
EN 12UNPACKING...

4. COMMANDS AND CONTROL INSTRUMENTS
1. STEERING WHEEL
Turns the front wheels.
2. A
CCELERATOR LEVER
Regulates the engines r.p.m. The positions are indicated on a plate showing the
following symbols:
Position «CHOKE»  for starting up.
Position «SLOW»  for minimum engine speed
Position «FAST»  for maximum engine speed
EN 13 COMMANDS AND CONTROL INSTRUMENTS
1
2
A
B3B
A
6
1234567
7
54 

When moving from one area to another, put the lever in a position between
«SLOW» and «FAST» When cutting, go to the «FAST» position.
3. P
ARKING BRAKE LEVER
This lever is to stop the machine from moving when it has been parked, and must
always be engaged before leaving the machine.
The brake is engaged by fully pressing the pedal (11 - 21) and moving the lever to
position «A». When you take your foot off the pedal it will be blocked by the lever
in the down position.
To disengage the parking brake, press...

If the blade is engaged when safety conditions have not been complied with, the
engine shuts down (see page 26).
On disengaging the blade (Pos. «A»), a brake is simultaneously activated which
stops it rotating in five seconds.
7. C
UTTING HEIGHT ADJUSTING LEVER
There are seven positions for this lever, shown as «1» to «7» on the label, which
correspond to various heights of between 3 and 8 cm.
To go from one height to another, move the lever sideways and put into one of the
seven notches.
For mechanical...