Digital Projection Titan Hd-500, Hd-250 User Manual

							Rev B  02/2007 Page 4.15
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the  
 key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
  If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the  
 key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
 (see On Screen Display, 
in Setup Menu, later in this 
section).)
Main menu: Input
  Input 4. is not used on this 
projector.
Main menu: Setup
Using the menus
Navigating menus and submenus
When the menus are in use and the OSD is ON, the top level menu headings are 
always visible to the left of the screen.
Each menu item can lead to a number of submenus, which are displayed in the 
column to the right . The 
 symbol indicates that a submenu is available.
Each submenu can lead to further submenus, up to a maximum of three levels.
To display the menus, press 
 on the remote control or the keypad.
 The menus will always open at the same point they were last viewed. The 
example below shows the fi rst menu display following power on – the item that is 
currently selected (the Input menu) is highlighted in blue.
To select a menu, press 
 and , for example the Setup menu: •
•
• 
						

							Page 4.16 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Press  to open the menu. The blue highlight moves to the fi rst item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press 
 and  , for example the Lamp submenu.
Press 
 to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press 
.
There may be up to three levels of submenu, so to return to the top level, you 
may have to press 
 up to three times.
To close the menu display completely, press 
. •
•
••
Notes
Setup menu
Setup menu
 Lamp
Setup menu 
						

							Rev B  02/2007 Page 4.17
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press 
 and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press 
 and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of input signal.
Parameter list
To select from a list of parameters, 
press 
 and .
Menu controls
Some menus have controls, as shown in the examples below.
Notes
  Some  menus items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal. 
						

							Page 4.18 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Input menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Input is highlighted.
Press 
 to open the Input menu. The blue highlight moves to the fi rst item in 
the menu. The 
 symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7. Component
Press 
 to confi rm your selection. •
••
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Input Menu
  Input 4. is not used on this 
projector.
  For more information about 
the input connections, see 
section 2. Installation, and 
section 7. Appendix.
  When an input has been 
selected, the projector will 
automatically detect input mode 
settings such as line rate and 
resolution etc.
  To force the projector to re-
detect the input mode settings, 
press 
. 
						

							Rev B  02/2007 Page 4.19
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
Input Menu
 Presets
Input Menu
 Presets
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu (1 – 7)
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except Global
Press 
 and   to select Presets. 
 Press 
 to open the Presets submenu.
Recall Presets
Press  and   to select Recall Preset.
 Press 
 to open the Recal Presets A ~ H submenu. Any presets that have 
been saved are indicated by their description, for example D: in this example.
To recall a set of parameters that has been saved, press 
 and   to select 
one of the Presets.
 For Presets J to S, select Recall Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
 Press 
 to confi rm your selection.
 The Preset parameters will be loaded. •
•
•
•
Input menu continued 
						

							Page 4.20 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
Input Menu
 Presets
    Save Presets A ~ H Save Presets
Press  and   to select Save Preset.
 Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press 
 and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
 Press 
 to confi rm your selection.
 If this Preset has been used before, but only if the Input source has been 
changed, then the following  message will be displayed.
 Press 
 and   to select either OK or Cancel.
 Press 
 to confi rm your selection.
 The parameters will be saved to the selected preset, and the following message 
will be displayed. •
•
Input menu continued 
						

							Rev B  02/2007 Page 4.21
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Picture Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and Component inputs 
only.
 The Hue slider is available for 
NTSC inputs only.
Picture menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Picture is highlighted.
Press 
 to open the Picture menu. The blue highlight moves to the fi rst item in 
the menu.
Brightness
Press  and   to select Brightness.
 Press 
 and   to adjust the slider (-128 to +127).
Contrast
Press  and   to select Contrast.
 Press 
 and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press 
 and   to select Saturation.
 Press 
 and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a reference.
Press 
 and   to select Hue.
 Press 
 and   to adjust the slider (0 to 255). •
•
•
•
• 
						

							Page 4.22 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
  For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The 
projector’s gamma adjustment can be used to correct for this.
Press 
 and   to select Gamma.
 Press 
 and   to select from:
Parametric  Enables the gamma slider
User download  Applies the gamma settings made externally using the DP 
Userware on a personal computer
Graphics  To be defi ned.
NTSC  NTSC colour space, with a gamma of 2.2
PA L  PAL colour space, with a gamma of 2.2
Punch  Enhanced brightness and increased colour saturation for high 
ambient environments.
Parametric Gamma
Press  and   to select Parametric Gamma.
 Press 
 and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality defi nition on, for example, fi ne text.
Press 
 and   to select Phase.
 Press 
 and   to adjust the slider (0 to 31). •
•
•
Picture menu continued 
						

							Rev B  02/2007 Page 4.23
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
 Press 
 and   to select from:
Fill  This will best fi t the incoming source to fi ll either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope  Use with the TheaterScope Anamorphic System only. The 
2.35:1 source image is displayed using the full area of the 16:9 
DMD. This is then stretched to 2.35:1 by the lens.
Native  The image will be displayed pixel for pixel. The image will 
be centred, with a black border if smaller than 1280 x 720 or 
cropped if larger.
Sharpness
Press  and   to select Sharpness.
 Press 
 and   to adjust the slider. •
•
Picture menu continued 
						

							Page 4.24 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
  Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
  When using the menus, press 
OSD 
 or  to hide or 
reveal the On-Screen-Display.
Geometry Menu
  Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings (see 
next page).
Geometry menu
  To return to the main menu, press  up to three times.
 From the main menu:
Press 
 and   until Geometry is highlighted.
Press 
 to open the Geometry menu. The blue highlight moves to the fi rst item 
in the menu.
Horizontal Position
Press  and   to select H Position.
 Press 
 and   to adjust the slider.
Vertical Position
Press  and   to select V Position.
 Press 
 and   to adjust the slider.
Aspect Ratio
 Press  and   to select from:
Fill  This will best fi t the incoming source to fi ll either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.25:1 (5:4)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope  Use with the TheaterScope Anamorphic System only. The 
2.35:1 source image is displayed using the full area of the 16:9 
DMD. This is then stretched to 2.35:1 by the lens.
Native  The image will be displayed pixel for pixel. The image will 
be centred, with a black border if smaller than 1280 x 720 or 
cropped if larger. •
•
•
•