Digital Projection Titan Hd-500, Hd-250 User Manual
Have a look at the manual Digital Projection Titan Hd-500, Hd-250 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Rev B 02/2007 Page 4.45 Digital Projection TITAN HD-500, HD-250 User Manual 4. Controlling the projector Notes Restore Defaults will restore all settings to factory defaults. If you are not sure this is what you want to do, then either: make a record of all settings fi rst or select No, then press . Following a restore to factory defaults, the projector will perform a self-test and enter Standby mode. This process will take up to 10 seconds. During this time the projector will not respond to any commands. When complete, all settings will be restored to factory condition and all user settings will be removed except for downloaded colour and gamma parameters. Restore Defaults Press and to select Restore Defaults. Press . The following message will be displayed. Press and to select from: Ye s Press to confi rm your that you really wish to restore all default settings. All settings will be restored to factory defaults. or No Press or to exit without making the change. • • Setup menu, continued
Page 4.46 Rev B 02/2007 4. Controlling the projector Digital Projection TITAN HD-500, HD-250 User Manual Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Information Menu Information Menu Projector Information The Lamp 2 information applies only to the HD-500. The HD- 250 has only one lamp. Information Menu Source Information Information menu To return to the main menu, press up to three times. From the main menu: Press and until Information is highlighted. Press to open the Information menu. The blue highlight moves to the fi rst item in the menu. Projector Information Press and to select Projector Information. Press to open the Projector Information submenu. Source Information Press and to select Source Information. Press to open the Source Information submenu. • • •
Rev B 02/2007 Page 4.47 Digital Projection TITAN HD-500, HD-250 User Manual 4. Controlling the projector Digital Projection Information Press and to select Digital Projection. Press to see the DP Information screen. • Information menu continuedNotes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Information Menu DP Contact Information
Page 4.48 Rev B 02/2007 4. Controlling the projector Digital Projection TITAN HD-500, HD-250 User Manual
Page 5.2 Rev B 02/2007 5. Userware Digital Projection TITAN HD-500, HD-250 User Manual
Rev B 02/2007 Page 6.1 6. Maintenance Contents Changing the lamp module .............................................................................................................. 6.2 Changing the air fi lter ........................................................................................................................ 6.3 Cleaning ................................................................................................................................................ 6.4 Projector .......................................................................................................................................... 6.4 Lens ................................................................................................................................................ 6.4 Lamp module ................................................................................................................................... 6.4
Page 6.2 Rev B 02/2007 6. Maintenance Digital Projection TITAN HD-500, HD-250 User Manual Changing the lamp module Turn the power OFF and allow the lamp to cool for 5 minutes. Unscrew the three door screws, and detach the rear door - the door is tethered, so cannot be removed completely. Disconnect the timer cable from the lamp module. Loosen the two captive fi nger screws securing the lamp module. Pull the lamp module to the right, then to the rear to remove it from the projector. Insert a new lamp module, manoeuvreing it carefully so that the plug on the top of the module mates properly with the socket in the roof of the cabinet. Tighten the two lamp fi xing screws. Reconnect the timer cable. Re-fi t the rear door, making sure that the door tether is not trapped, and tighten the four screws. • • • • • • • • • Notes Always allow the lamp to cool for 5 minutes before: - disconnecting the power - moving the projector - changing the lamp There are no user-serviceable parts inside the lamp module. The whole module should be replaced. At the end of life, the lamp will not strike, and the Lamp Indicator on the control panel will show red. (Typical lamp life is 1500 hours) Do not use the lamp for more than 1500 hours, as this may cause serious lamp failure, damage the lamp module and cause extra cost on replacement. Take care not to touch the glass surface of the lamp module. If you do accidentally touch the glass, it should be cleaned before use. HID lamps produce high intensity light. Do not look directly at the light coming from the lamp housing or the lens. The fi lter should be changed at the same time as the lamp is changed - see next page. The projector cannot be operated until the door is fully closed. Door screws Lamp screws Timer cable
Rev B 02/2007 Page 6.3 Digital Projection TITAN HD-500, HD-250 User Manual 6. Maintenance Changing the air fi lter Turn the power OFF and allow the lamp to cool for 5 minutes. Unscrew the three door screws, and remove the rear door. Pull out the air fi lter. Fit a new air fi lter. Re-fi t the rear door, making sure that the door tether is not trapped, and tighten the three screws. • • • • • Notes Always allow the lamp to cool for 5 minutes before: - disconnecting the power - moving the projector - changing the lamp The air fi lter should be changed regularly: - In a clean environment such as an offi ce, change after 1500 hours, at the same time as the lamp is changed. - In a dusty or smoky environment such as a theatre or public area, more frequent changes may be necessary. Opening the rear door will switch the projector OFF. The projector cannot be operated until the door is fully closed.
Page 6.4 Rev B 02/2007 6. Maintenance Digital Projection TITAN HD-500, HD-250 User Manual Notes Never use strong detergents or solvents such as alcohol or thinners to clean the projector and lens. NEVER touch the lamp or refl ector. Cleaning Turn the projector off before cleaning. Projector Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Lens Use a blower or lens paper to clean the lens, taking care not to scratch the glass. Lamp module Use a blower or lens paper to clean ONLY the glass window, taking care not to scratch the glass.