Digital Projection Thunder 9000gv User Manual

E – 15
Projector Orientation
An image can be projected from in front or behind a screen, and the
projector can be installed on the ceiling*.
Ceiling Front Projection
Use [Projector Options] →[Setup] →[Page 1] →[Orientation] to select
Ceiling Front. (See page E-36.)
Ceiling Rear Projection
Use [Projector Options] →[Setup] →[Page 1] →[Orientation] to select
Ceiling Rear. (See page E-36.)
Desktop Rear Projection
Use [Projector Options] →[Setup] →[Page 1] →[Orientation] to select
Desktop Rear. (See page...

E – 16
When used in standalone operation
Connecting Your PC Or Macintosh Computer
Connecting your PC or Macintosh computer to THUNDER 9000gv
Projector will enable you to project your computers screen image for an
impressive presentation.
To connect to a PC or Macintosh :
1. Turn off the power to your projector and computer.
2. Use a signal cable (not provided) to connect your PC or Macintosh
computer to the projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a...

E – 17
OUTPUT
INPUT3
OPTION
REMOTE1RGB
OUTIN
REMOTE2
REMOTE3INPUT7
INPUT8 INPUT5 INPUT6
OUT
LED
ON
OFF IN
INY
C S-VIDEO1
S-VIDEO2 VIDEO1 VIDEO2 R/Cr
B/CbCb
H/HV
V VH/HV B/CbG/Y G/YR/CrCr
SDI Y
INPUT2 INPUT1 INPUT4
OUTPUT
INPUT0
RGB DIGITALINPUT9
OUT
When Used with One Switcher (ISS-6020/ISS-6020G)
Up to 10 input signals can be accepted when the projector is connected to one Switcher. Using the projector with the Switcher allows easy
adjustment and signal selection.
•Select [Advanced Menu] → [Projector...

E – 18
When Used with Two or More Switchers  (100
Inputs)
Up to 100 inputs can be accepted using the ISS-6020 Switcher.
How to make connections:
1. Connect the REMOTE 1 terminal of the master Switcher to the RE-
MOTE 1 of the projector using the optional control cable (15p-15p/
CTL-6010).
2. Next connect the REMOTE 2 terminal of the master Switcher to the
REMOTE 1 terminal of the first slave Switcher using the same op-
tional control cable as mentioned above. Third, connect the REMOTE
2 terminal of the...

E – 19
Set the DIP switch (S8601) of the Switcher as follows:
The Projector
Slot 1 of the Master
Slot 2 of the Master
Slot 3 of the Master
Slot 4 of the Master
Slot 5 of the Master
Slot 6 of the Master
Slot 7 of the Master
Slot 8 of the Master
Slot 9 of the Master
Slot 10 of the MasterMaster
Slave 1
Slave 2
Slave 3
Slave 4
Slave 5
Slave 6
Slave 7
Slave 8
Slave 9
Slave 10 ISS-6020
ISS-6020GOutput toSetting of S8601
NOTE: Slave numbers 1 to 10 must correspond to the master’s slot numbers 1 to 10.
OPEN...

E – 20
REMOTE 1 Connector
Pin Configuration of Optional CTL-6010 Cable
REMOTE 1 connector
of the Switcher mini D-
sub 15 pin (female) REMOTE 1 connector of
the Projector mini D-sub
15 pin (female)
Shield (frame ground)
Pins without a number are open.
51423
10
11 12 13 14 156 978
This connector is used for either connecting the ISS-6020/ISS-6020G Switcher or a third
par ty external control device (Contact Closure). When the Switcher is used, connect it with
the optional control cable (15-15 pin; 50...

E – 21
When used in stand alone operation.
Pin No.
14
5
10
4,8,12,11SHORT/OPEN
SHORT
OPEN
SHORT
OPEN
SHORT
OPENFUNCTION
External control mode ON
External control mode OFF
POWER ON
POWER OFF
PICTURE MUTE ON
PICTURE MUTE OFF
*When the combinations other than specified in the above table are selected, the input will be forcefully switched to RGB 1.
*The term “SHORT” means to connect with pin 15
*When in the external control mode, the POWER, INPUT, PICTURE MUTE and SOUND MUTE buttons on the remote control...

E – 22
REMOTE2
INPUT7S-VIDEO1
Y
C IN
OUT
Operating Multiple Projectors with the Remote Control
You can operate multiple projectors with the same remote control in wireless operation.
To  do so:
1. Select [Advanced Menu] → [Projector Options] → [Setup] → [Page 5] → [Projector ID] and assign an ID number to each projector. See also page
E-37.
2. On the remote control specify the ID number of the projector to be adjusted. Press and hold the CTL and press MENU (ADDRESS) button to
enter the ID number.
You can...

E – 23
Using the RGB DIGITAL connectors
The Link mode function allows you to adjust or set multiple projectors using the RGB DIGITAL and OPTION connectors.
The DVI DIGITAL input accepts up to the XGA (1024 x 768 @85Hz) signal.
NOTE: The Auto Adjust feature does not work for DVI digital signal. When DVI signal is selected and the image position is not corrected, adjust the horizontal andvertical position using the Position screen. See page E-31 for more details.
Connection for Double Stacking in Link...

E – 24
Using The Menus
1. Press the MENU button on the remote control to display the menu.
2. Use the ▲ or ▼ button on the remote control to select the sub menu.
3. The right-oriented delta symbol indicates further choices are avail-
able. Press the 
 button to highlight the item you want to adjust or set
in the selected menu.
4. Press the ▲ or ▼ button on the  remote control to select the item.
5. Press the ENTER button on the remote control to display the adjust-
ment screen or dialog box.
6. Adjust...