Digital Projection Projector M-Vision Cine LED User Manual

							Rev E October 2014 Page 6.3
Digital Projection M-Vision Cine LED User  Manual 6. Appendix
ProblemPossible solutions
Image is split or otherwise scrambled.Check that the image source is not set to progressive scan.
Image is blurred.Check that the lens is focussed correctly.
Image is too bright, and lacks 
definition in the bright areas.
Decrease the contrast setting.
See section 4. Controlling the projector, Using the control keys and Main 
menu
Image appears ‘washed out’ and is too 
bright in the dark areas
Decrease the brightness setting.
See section 4. Controlling the projector, Using the control keys and Main 
menu
Colors in the image are swapped. 
for example, reds appear blue or vice 
versa.
Check that the Component signals are connected correctly.
See Section 4. Installation, Connecting the projector.
Projector does not respond to control 
commands from a computer.
Check that the serial cable is connected correctly.
Check that the baud rate is set correctly.
See this section 6. Appendix, Connections
Check that the correct control codes are being used.
See this section 6. Appendix. Serial communications protocol
Projector does not respond to control 
commands from the remote control.
Check that the infra red windows at the front and rear of the projector or on the IR 
repeater are not obstructed. Check that the batteries are in good condit\
ion.
If you are using an IR repeater, check that the cable is connected properly at both 
ends, and that the cable is not damaged.
See section 4. Controlling the projector, The remote control
In the event that this troubleshooting guide has not solved the problem,\
 
then contact your Digital Projection dealer or service centre. 
						

							Page 6.4 Rev E October 2014
6. Appendix Digital Projection M-Vision Cine LED User Manual
Error codes
If the projector detects an error, the red Issue indicator will flash, as shown in the 
chart below.
For example, if the fan fails, the red indicator will flash twice followed by a pause, 
then the sequence will repeat until the error condition is corrected.
Notes 
						

							Rev E October 2014 Page 6.5
Digital Projection M-Vision Cine LED User  Manual 6. Appendix
Specifications
Part numbers
Projector
0.73:1 fixed lens 110-001
1.56–1.86:1 zoom lens 110-002
1.85–2.40:1 zoom lens 110-003
Power cable 10A, Europe 102-163
Power cable 13A, North America 102-165
Power cable 10A, United Kingdom 102-180
Remote control 109-685
User manual on CD 110-288
Important Information 110-287
Getting Started Guide 111-185
Replacement parts
LED module 109-683
0.8x converter lens 109-727
1.25x converter lens 109-735
Optical
Digital Light Processor 1 x 0.95” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Colour system  3-cycle (nomal running mode): Red/Green/Blue 
5-cycle (Brilliant Color on): Red/Green/Blue/Yellow/Cyan
Contrast Ratio  10000:1 (±10%)
Colour temperature adjustable: 5500K - 9300K
Pixel fill factor  87%
Lamp life (typical)  60000 hours
Brightness 1000 ANSI lumens (±10%)
Uniformity  85%
Focus range
0.73:1 Fixed lens to be confirmed
1.56–1.86:1 zoom lens  2–7m (6.6 - 23ft)
1.85–2.40:1 zoom lens 2.5–10m (8.2 - 32.8ft)
Image width
0.73:1 fixed lens to be confirmed
1.56–1.86:1 zoom lens 0.86 to 5.6m (2.8 - 18.4ft) depending on lens converter
1.85–2.40:1 zoom lens 0.81 to 6.86m (2.7 - 22.2ft) depending on lens converter 
						

							Page 6.6 Rev E October 2014
6. Appendix Digital Projection M-Vision Cine LED User Manual
Lens aperture
0.73:1 fixed lens F/2.5
1.56–1.86:1 zoom lens F/2.5–2.76
1.85–2.40:1 zoom lens F/2.17–2.46
Lens shift (zoom lenses only)
Vertical ± 0.6 H (120%)
Horizontal ± 0.15 W (30%)
Electrical
Inputs HDMI x 2, RGB, Component x 2, Video, S-Video
Pixel clock (digital) up to 165MHz
Bandwidth (analog) 200MHz
Control inputs  1 x RS232 serial: 38400 baud, 8 bits, 1 stop bit, no parity
  1 x remote control
Mains voltage 100-240 VAC ±10%, 47-63Hz (single phase)
Power consumption
110V  normal running mode: 240W, Brilliant Color on: 280W, Standby: 
						

							Rev E October 2014 Page 6.7
Digital Projection M-Vision Cine LED User  Manual 6. Appendix
Dimensions
All dimensions in mm 
unless otherwise stated 
						

							Page 6.8 Rev E October 2014
6. Appendix Digital Projection M-Vision Cine LED User Manual
Video formats supported
Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
PC640x480 59.94xxxVESA DMT 
640x480 74.99xxxVESA DMT 
640x480 85xxxVESA DMT 
800x600 60.32xxxVESA DMT 
800x600 75xxxVESA DMT 
800x600 85.06xxxVESA DMT 
848x480 47.95xxxVESA CVT 
848x480 59.94xxxVESA CVT 
1024x768 60xxxVESA DMT 
1024x768 75.03xxxVESA DMT 
1024x768 85.03xxxVESA DMT 
1024x768 70.1xxxVESA DMT 
1280x720 47.95xxxVESA GTF 
1280 x 768 60xxxVESA DMT 
1280 x 768 60xxxVESA DMT Reduced Blanking
1280 x 768 75xxxVESA DMT 
1280 x 768 85xxxVESA DMT 
1280 x 800 50x xxVESA DMT
1280 x 800 60xxxVESA DMT 
1280 x 800 75xxxVESA DMT 
1280x1024 60.02xxxVESA DMT 
1280x1024 75.02xxxVESA DMT 
1280x1024 85.02xxxVESA DMT 
1440 x 900 60xxxVESA DMT 
1440 x 900 75xxxVESA DMT 
1400 x 1050 60xxxVESA DMT 
1400 x 1050 75xxxVESA DMT 
1600x1200 60xxxVESA DMT 
1920x1080 47.95xxxVESA CVT 
1600 x 1200 60xxxVESA DMT 
1920 x 1200 60xxxVESA DMT Reduced Blanking 
1680x1050 59.94xxxVESA CVT 
Apple Mac 640x480 66.59xxxVESA DMT 
832x624 74.54xxxVESA DMT  
						

							Rev E October 2014 Page 6.9
Digital Projection M-Vision Cine LED User  Manual 6. Appendix
Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
NTSC NTSC (M, 4.43) 59.94x x ITU-R BT.1700, SMPTE 170M
PA L PAL (B,G,H,I) 50x x ITU-R BT.1700 
PAL (N) 50x x ITU-R BT.1700 
PAL (M) 59.94x x ITU-R BT.1700 
SECAM SECAM (M) 50x x ITU-R BT.1700 
480i 59.94xxxSMPTE 125M, CEA-861-D 
576i 50xxxITU-R BT.601, CEA-861-D 
EDTV 480p 59.94xxxxxSMPTE 293M, CEA-861-D 
576p 50xxxxxITU-R BT.1358, CEA-861-D 
HDTV 1035i 60xxxxxSMPTE 260M 
1080i 50xxxxxSMPTE 274M, CEA-861-D 
1080i (Aus) 50xxxxxSMPTE 295M 
1080i 59.94xxxxxSMPTE 274M, CEA-861-D 
1080i 60xxxxxSMPTE 274M, CEA-861-D 
720p 50xxxxxSMPTE 296M, CEA-861-D 
720p 59.94xxxxxSMPTE 296M, CEA-861-D 
720p 60xxxxxSMPTE 296M, CEA-861-D 
1080p 23.98xxxxxSMPTE 274M, CEA-861-D 
1080p 24xxxxxSMPTE 274M, CEA-861-D 
1080p 25xxxxxSMPTE 274M, CEA-861-D 
1080p 29.97xxxxxSMPTE 274M, CEA-861-D 
1080p 30xxxxxSMPTE 274M, CEA-861-D 
1080p 50xxxxxSMPTE 274M, CEA-861-D 
1080p 59.94xxxxxSMPTE 274M, CEA-861-D 
1080p 60xxxxxSMPTE 274M, CEA-861-D  
						

							Page 6.10 Rev E October 2014
6. Appendix Digital Projection M-Vision Cine LED User Manual
NotesInput connections
HDMI 1 & 2 inputs
19 way type A connector
1 TMDS Data 2+
2 TMDS Data 2 Shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 Shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 Shield
9 TMDS Data 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 not connected
15 SCL (DDC Clock)
16 SCA (DDC Data)
17 DDC/CEC Ground
18 +5 V Power
19 Hot Plug Detect
Composite video input
1 x RCA phono connector
PAL or NTSC video
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
pin view of panel connector
pin view of female connector 
						

							Rev E October 2014 Page 6.11
Digital Projection M-Vision Cine LED User  Manual 6. Appendix
pin view of female connector
RGB input
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Component 1 input
3 x RCA phono connectors
RGsB   YPbPr  YCbCr
Green + Sync     Y    Y
Blue      Pb   Cb
Red      Pr   Cr
RGBS
connect Sync to Video input
Component 2 input
3 x 75 ohm BNC
RGsB   YPbPr  YCbCr
Green + Sync     Y    Y
Blue      Pb   Cb
Red      Pr   Cr
Notes
 In most cases, the Auto setting 
will determine the correct color 
space to use. If it does not, 
you can select the appropriate 
setting manually. 
  To select between RGB and 
YPrPb signals, see Advanced 
Menu, in 4.Controlling the 
Projector. 
						

							Page 6.12 Rev E October 2014
6. Appendix Digital Projection M-Vision Cine LED User Manual
Control connections
Wired Remote control connection
3.5mm mini jack
Tip  Signal
Ring Not connected
Sleeve Ground
Trigger 1 & 2 output
3.5mm mini jack
Tip  Signal
Sleeve Ground
Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a modem)
RX  2 --- 3 TX
TX 3 --- 2 RX
GND 5 --- 5 GND
Serial port settings
•	Baud rate  38400 bps
•	Data length 8 bits
•	Stop bits one
•	Parity none
•	Flow control none
Notes
 Trigger outputs are normally 
at 0V, and rise to +12V when 
triggered.
 The projector is a DCE, so use:
•	a straight cable to connect to a 
computer, or
•	a null-modem cable as shown 
here to connect to another DCE 
such as a modem.
Sleeve
Ring
Tip
SleeveTip
pin view of female connector