Digital Projection Projector M-Vision Cine LED User Manual
Have a look at the manual Digital Projection Projector M-Vision Cine LED User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Rev E October 2014 Page 4.23 Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector Rear Projection • Use the and keys to select from: On Projected image is reversed, left to right Off Ceiling Mode • Use the and keys to select from: On Projected image is reversed, top to bottom Off Logo Display • Use the and keys to select from: On The Digital Projection logo is displayed during power up Off Notes To exit from the menus completely, you may need to press up to three times. Image changes made using the menus will take effect immediately. System menu continued
Page 4.24 Rev E October 2014 4. Controlling the projector Digital Projection M-Vision Cine LED User Manual Notes To select a different menu, press MENU once or twice, so that no items are highlighted, then use the the and keys to select a different page. To exit from the menus completely, you may need to press up to three times. For more information about the trigger output, see Control connections in section 6. Appendix. For more information about RS232 commands, see Remote communications protocol in section 6. Appendix. Control menu • To display the menus, press MENU on the remote control or the projector control panel. • Use the and keys to select the Control menu page, • To select a menu item, use the and keys until the item is highlighted. Trigger 1 & 2 The Trigger 1 and Trigger 2 outputs are interchangeable: Screen trigger: can be connected to an electrically operated screen, automatically deploying the screen when the projector starts up, and retracting the screen when the projector shuts down. Aspect Ratio trigger: can be used to control screen shuttering for different aspect ratios • For each Trigger setting, use the and keys to select from: Screen trigger occurs when the projector is in RUNNING mode 16:9 trigger occurs when 16:9 aspect ratio is selected Theaterscope trigger occurs when Theaterscope aspect ratio is selected 4:3 trigger occurs when 4:3 aspect ratio is selected 4:3 Narrow trigger occurs when 4:3 Narrow aspect ratio is selected RS232 trigger output follows the On or Off setting specified in a trig.1 or trig.2 command received from a PC via the RS232 serial input.
Rev E October 2014 Page 4.25 Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector Notes To set what a ‘blank’ screen looks like, use the Blank Screen setting in the System menu. To select a different menu, press MENU once or twice, so that no items are highlighted, then use the the and keys to select a different page. To exit from the menus completely, you may need to press up to three times. If a source has been disabled in the System menu, then a key programmed with that source will have no effect. Auto Source • Use the and keys to select from: On projector searches for an alternative input source when the current input source is disconnected Off projector shows a ‘blank’ screen when the current input source is disconnected Keys 1 to 5 The to keys on the remote control can each be programmed to switch to one of the seven input sources. • Use the and keys to select a Key, then press ENTER or SELECT. The Key submenu will appear: • Use the and keys to select from: HDMI 1 HDMI 2 RGB Component 1 Component 2 Video S-Video • Press ENTER or SELECT to confirm your selection. • Press MENU to return to the Control menu and select another key. Control menu continued
Page 4.26 Rev E October 2014 4. Controlling the projector Digital Projection M-Vision Cine LED User Manual Notes To select a different menu, press MENU once or twice, so that no items are highlighted, then use the the and keys to select a different page. To exit from the menus completely, you may need to press up to three times. Restore Defaults will restore all settings to factory defaults. If you are not sure this is what you want to do, then either: make a record of all settings first or select No, then press ENTER or SELECT Service menu • To display the menus, press MENU on the remote control or the projector control panel. • Use the and keys to select the Service menu page, The first eight items are for information only, and cannot be changed. • To select a menu item, use the and keys until the item is highlighted. Factory Reset • Press ENTER or SELECT to request a Factory Reset. The following message will be displayed. • Use the and keys to select from: Yes all settings will be restored to factory defaults No Press ENTER or SELECT to confirm your choice.
Rev E October 2014 Page 4.27 Digital Projection M-Vision Cine LED User Manual 4. Controlling the projector Blue Only This is useful for color-calibrating the projector or other video components. • Use the and keys to select from: On only the blue signal is displayed - green and red are turned off Off all three signals - red, green and blue - are displayed Test Patterns • Use the and keys to select from: Test Pattern Off White Black Red Green Blue Cyan Magenta Yellow Chequerboard Greyscale Alignment grid • To turn the test pattern Off, press any other key. Altitude For use at high altitudes where the air is thinner, the fan speed can be increased. • Use the and keys to select from: Low normal speed fan High high speed fan Notes To exit from the menus completely, you may need to press up to three times. Image changes made using the menus will take effect immediately. Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. If the projector frequently overheats when used in a high altitude environment, then it may help to use the High Altitude setting. In most cases, the Low Altitude setting should be satisfactory. Service menu continued
Page 4.28 Rev E October 2014 4. Controlling the projector Digital Projection M-Vision Cine LED User Manual
Rev E October 2014 Page 5.1 5. Maintenance Contents Changing the LED module ...............................................................................................................5.2 Cleaning the fans ................................................................................................................................5.2
Page 5.2 Rev E October 2014 5. Maintenance Digital Projection M-Vision Cine LED User Manual Changing the LED module • The LED module should be changed only by qualified and authorised service personnel. • Contact your Digital Projection Dealer. Notes The LED module in this projector should be changed ONLY by authorised and qualified service personnel. Always switch the projector OFF before cleaning the fans. The fans should be cleaned regularly: • In a clean environment such as an office, after 500 hours. • In a dusty or smoky environment such as a theatre or public area, more frequent cleaning may be necessary. Cleaning the fans • Turn the power OFF and wait until the fans stop. • Use a vacuum cleaner to clean the inlet and outlet fans, as shown below .
Rev E October 2014 Page 6.1 6. Appendix Contents Troubleshooting ..................................................................................................................................6.2 Error codes ......................................................................................................................................6.4 Specifications ......................................................................................................................................6.5 Part numbers ....................................................................................................................................6.5 Optical .............................................................................................................................................6.5 Electrical ..........................................................................................................................................6.6 Physical ...........................................................................................................................................6.6 Dimensions ..........................................................................................................................................6.7 Video formats supported ..................................................................................................................6.8 Input connections .............................................................................................................................6.10 HDMI 1 & 2 inputs ...........................................................................................................................6.10 Composite video input .....................................................................................................................6.10 S-Video input ..................................................................................................................................6.10 RGB input .......................................................................................................................................6.11 Component 1 input ...........................................................................................................................6.11 Component 2 input ...........................................................................................................................6.11 Control connections ........................................................................................................................6.12 Wired Remote control connection .....................................................................................................6.12 Trigger 1 & 2 output ........................................................................................................................6.12 Serial control input ..........................................................................................................................6.12 Null-modem cable .........................................................................................................................6.12 Serial port settings ........................................................................................................................6.12 Remote communications protocol ...............................................................................................6.13 Introduction ....................................................................................................................................6.13 Key Commands ..............................................................................................................................6.13 Example .....................................................................................................................................6.13 The commands ............................................................................................................................6.13 Operation Commands .....................................................................................................................6.15 Example .....................................................................................................................................6.15 The commands ............................................................................................................................6.15
Page 6.2 Rev E October 2014 6. Appendix Digital Projection M-Vision Cine LED User Manual Troubleshooting ProblemPossible solutions The red ISSUE indicator is illuminated continuously or flashing. Check the Error codes detailed on the next page. The projector will not power up.Note that the blue POWER indicator light will be OFF when the projector is in normal RUNNING MODE. Check that the mains plug is plugged in and that the mains supply is swi\ tched on. Check any external fuses or breakers. The projector will not power up shortly after being switched off. To protect the LED module, the projector cannot be switched on when in it is in cool-down mode. Wait until the power indicator shows steady blue. showing that it is in standby mode. The projector shuts down after it has been in use for some time. The projector may be overheating. Check that the air inlets and outlets are clear of any obstruction. See section 5. Maintenance, Cleaning the fans It is possible to increase the speed of the fans for use in a high altitude environment: See section 4. Controlling the projector, System menu No image is displayed.Check that the input source is switched on and connected to the projector correctly. Check that the correct image source is selected. Check that the brightness and contrast settings are set correctly. See section 4. Controlling the projector, Using the control keys and Main menu The projector may be overheating. Check that the air inlets and outlets are clear of any obstruction. The image does not fit the screen correctly. Check that the projector and screen size are positioned correctly , and that the zoom is adjusted correctly. See section 2. Installation, Screen size vs throw distance Check the aspect ratio setting. See section 4. Controlling the projector, Main menus Uneven image quality.Check that the projector is parallel to the screen. Check that the screen is flat, and securely mounted.