Digital Projection Projector M Vision Cine 230 User Manual

							
Rev A December 2010 Page 4.21
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 4. Controlling the projector

Source Enable
Press ENTER or SELECT.
The Source Enable submenu will appear:
Use the  and  keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
For each source, use the  and  keys to select from:
On the selected source will be included in an automatic input source 
search
Off the selected source will not be included in an automatic input 
source search
To return to the System menu, press MENU  once.
•
•
•
•
System menu continuedNotes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times. 
						

							
Page 4.22 Rev A December 2010
4. Controlling the projector Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Menu Position
Use the  and  keys to select from:
Top left
Top right
Bottom left
Bottom right
Centre
Blank Screen
This option determines what appears on screen when the projector is sear\
ching for 
a valid input source.
Use the  and  keys to select from:
Digital Projection logo
Black screen
Blue screen
White screen
Auto Power On
Use the  and  keys to select from:
On    When power is connected, the projector starts up imediately.
Off   When power is connected, the projector goes into Standy mode, 
and does not start until POWER ON  on the remote control 
or POWER  on the projector control panel is pressed.
Auto Power Off
When the projector is searching for a valid input source, this option de\
termines what 
appears on screen.
Use the  and  keys to select from:
On    The projector automatically goes into Standby mode if no input 
source is detected for 20 minutes.
Off   The projector stays on until POWER OFF   on the remote 
control or POWER  on the projector control panel is pressed.
•
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
System menu continued 
						

							
Rev A December 2010 Page 4.23
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 4. Controlling the projector

Rear Projection
Use the  and  keys to select from:
On   Projected image is reversed, left to right
Off
Ceiling Mode
Use the  and  keys to select from:
On   Projected image is reversed, top to bottom
Off
Logo Display
Use the  and  keys to select from:
On   The Digital Projection logo is displayed during power up
Off
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
System menu continued 
						

							
Page 4.24 Rev A December 2010
4. Controlling the projector Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 For more information about 
the trigger output, see Control 
connections in section 
6.  Appendix. 
 For more information about 
RS232 commands, see Remote 
communications protocol in 
section 6.  Appendix.
Control menu
To display the menus, press MENU  on the remote control or the projector 
control panel.
Use the  and  keys to select the Control menu page,
To select a menu item, use the  and  keys until the item is highlighted.
Trigger 1 & 2
The Trigger 1 and Trigger 2 outputs are interchangeable:
Screen trigger: can be connected to an electrically operated screen, 
automatically deploying the screen when the projector 
starts up, and retracting the screen when the projector 
shuts down.
Aspect Ratio trigger: can be used to control screen shuttering for different 
aspect ratios
For each Trigger setting, use the  and  keys to select from:
Screen  trigger occurs when the projector is in RUNNING mode
16:9  trigger occurs when 16:9 aspect ratio is selected
Theaterscope trigger occurs when Theaterscope aspect ratio is selected
4:3 trigger occurs when 4:3 aspect ratio is selected
4:3 Narrow trigger occurs when 4:3 Narrow aspect ratio is selected
 RS232 trigger output follows the On or Off setting specified in a trig.1 or 
trig.2 command received from a PC via the RS232 serial input.
•
•
•
• 
						

							
Rev A December 2010 Page 4.25
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 4. Controlling the projector

Notes
 To set what a ‘blank’ screen 
looks like, use the Blank 
Screen setting in the System 
menu.
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 If a source has been disabled in 
the System menu, then a key 
programmed with that source 
will have no effect.
Auto Source
Use the  and  keys to select from:
On  projector searches for an alternative input source when the current 
input source is disconnected
Off projector shows a ‘blank’ screen when the current input source is 
disconnected
Keys 1 to 5
The  to   keys on the remote control can each be programmed to switch 
to one of the seven input sources.
 Use the  and  keys to select a Key, then press ENTER or SELECT.
The Key submenu will appear:
Use the  and  keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
Press ENTER or SELECT  to confirm your selection.
Press MENU  to return to the Control menu and select another key.
•
•
•
•
•
Control menu continued 
						

							
Page 4.26 Rev A December 2010
4. Controlling the projector Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 To select a different menu, 
press MENU  once or 
twice, so that no items are 
highlighted, then use the 
 and  keys to select a 
different page.
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Restore Defaults will restore 
all settings to factory 
defaults.
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press ENTER or 
SELECT
Service menu
To display the menus, press MENU  on the remote control or the projector 
control panel.
Use the  and  keys to select the Service menu page,
The first eight items are for information only, and cannot be changed.
To select a menu item, use the  and  keys until the item is highlighted.
Factory Reset
Press ENTER or SELECT  to request a Factory Reset.
 The following message will be displayed.
Use the  and  keys to select from:
Yes   all settings will be restored to factory defaults
  No
Press ENTER or SELECT to confirm your choice.
•
•
•
•
• 
						

							
Rev A December 2010 Page 4.27
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 4. Controlling the projector

Blue Only
This is useful for color-calibrating the projector or other video compon\
ents.
Use the  and  keys to select from:
On only the blue signal is displayed - green and red are turned off
Off    all three signals - red, green and blue - are displayed
Test Patterns
Use the  and  keys to select from:
Test Pattern Off
White
Black
Red
Green
Blue
Cyan
Magenta
Yellow
Chequerboard
Greyscale
Alignment grid
To turn the test pattern Off, press any other key.
Altitude
For use at high altitudes where the air is thinner, the fan speed can be increased.
Use the  and  keys to select from:
Low normal speed fan
High   high speed fan
•
•
•
•
Notes
 To exit from the menus 
completely, you may need to 
press  up to three times.
 Image changes made using 
the menus will take effect 
immediately.
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 If the projector frequently 
overheats when used in a high 
altitude environment, then 
it may help to use the High 
Altitude setting.
  In most cases, the Low Altitude 
setting should be satisfactory.
Service menu continued 
						

							
Page 4.28 Rev A December 2010
4. Controlling the projector Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 
						

							
Rev A December 2010  Page 5.1
5. Maintenance
Contents
Changing the lamp module ........................................................................\
......................................5.2
Cleaning the fans ........................................................................\
........................................................5.3 
						

							
Page 5.2 Rev A December 2010
5. Maintenance Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Changing the lamp module
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the captive finger screw securing the lamp door, and remove the door.
Unscrew the two cross-head screws securing the lamp module to the projec\
tor
Lift the wire handle up and use it to pull out the lamp module.
Fit a new lamp module, pushing it firmly into place.
Tighten the two cross-head screws.
Locate the two lugs at the bottom of the lamp door into the slots, and r\
e-fit the 
door. Tighten the finger screw.
•
•
•
•
•
•
•
Notes
 Always allow the lamp to cool 
for 5 minutes before: 
- disconnecting the power 
- moving the projector 
- changing the lamp
 There are no user-serviceable 
parts inside the lamp module. 
The whole module should be 
replaced.
 Only lamps supplied by 
Digital Projection and 
intended for this projector 
should be used. Fitting any 
other lamp could damage 
both projector and lamp, and 
will invalidate the warranty.
  At the end of life, the lamp 
will not strike, and the Issue 
indicator on the control panel 
will flash red. (Typical lamp life 
is 2000 hours)
 Do not use the lamp for more 
than 2000 hours, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement. 
 Take care not to touch the 
glass surface of the lamp 
module. If you do accidentally 
touch the glass, it should be 
cleaned before use.
 HID lamps produce high 
intensity light. Do not look 
directly at the light coming 
from the lamp housing or the 
lens.
  Opening the lamp door will 
switch the projector OFF. The 
projector cannot be operated 
until the door is fully closed.