Digital Projection Projector M Vision Cine 230 User Manual

							
Rev A December 2010
M-Vision Cine 230, Cine 260 HB, HC 
M-Vision Cine 400
High Brightness Digital Video Projector 
16:9 widescreen display
User Manual
111-260A 
						

							
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 
						

							
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Declaration of Conformity
Directives covered by this Declaration
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Equipment Directive.
Products covered by this Declaration
Large screen video projector type     The CE mark was first applied in: 
M-Vision Cine 230        October 2010 
M-Vision Cine 260  HB, HC     May 2010 
M-Vision Cine 400        October 2010
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of\
 the above EU directives, and the 
manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance C\
haracteristics of Information 
Technology Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteri\
stics of Information Technology 
Equipment.
EN 60950-1:2001 - Specification for Safety of Information Technology Equipment, including Electrical Business 
equipment.
The technical documentation required to demonstrate that the products me\
et the requirements of the Low Voltage 
directive has been compiled by the signatory below and is available for \
inspection by the relevant enforcement 
authorities.
Signed:   
Authority:     D.J. Quinn, Product Development Director
     
Date:    15 October 2010
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which 
must be observed when these products are taken into service to maintain \
compliance with the above directives. 
Details of these special measures are available on request, and are also\
 contained in the product manuals. 
						

							
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 
						

							
Rev A December 2010  Page v
Please read this user manual carefully before using the projector, and keep 
the manual handy for future reference.
A serial number is located on the back of the projector. Record it here: 
Symbols used in this guide
Warnings
 ELECTRICAL WARNING: this symbol indicates that there is a danger of 
electrical shock unless the instructions are closely followed.
 WARNING: this symbol indicates that there is a danger of physical 
injury to yourself and/or damage to the equipment unless the 
instructions are closely followed.
  NOTE: this symbol indicates that there is some important information that 
you should read.
Trademarks
IBM is a registered trademark of International Business Machines Corpora\
tion.
Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
Other product and company names mentioned in this user’s manual may be the 
trademarks of their respective holders.
Product revision
Because we at Digital Projection continually strive to improve our produ\
cts, we 
may change specifications and designs, and add new features without prio\
r 
notice. Projectors built prior to this revision of the User Manual may t\
herefore not 
include all the features described.
Manual revision
DateDescriptionRevision
December 2010Rev A
•
•
•
•
Important Information 
						

							
Page vi Rev A December 2010
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

General precautions
 Do not open the cabinet. There are no user serviceable parts inside.
  Use only the power cable provided.
 Ensure that the power outlet includes a Ground connection, as this 
equipment MUST be earthed.
 Take care to prevent small objects such as paper or wire from falling 
into the projector. If this does happen, switch off immediately, and have 
the objects removed by authorised service personnel.
 Do not expose the projector to rain or moisture, and do not place any 
liquids on top of the projector.
 Unplug before cleaning, and use a damp, not wet, cloth.
 Do not touch the power plug with wet hands.
 Do not touch the power plug during a thunder storm.
 Handle the power cable carefully and avoid sharp bends. Do not use a 
damaged power cable.
 There are no user-serviceable parts inside the lamp module. The whole 
module should be replaced.
  Only lamps supplied by Digital Projection and intended for this 
projector should be used. Fitting any other lamp could damage both 
projector and lamp, and will invalidate the warranty.
 Take care when removing the lamp module.
 NEVER touch the lamp or reflector.
 Take care not to touch the glass surface of the lamp module. If you 
do accidentally touch the glass, it should be cleaned before use. (see \
section 5. Maintenance.)
 Do not use the lamp for more than 2000 hours, as this may cause 
serious lamp failure, damage the lamp module and cause extra cost on 
replacement. 
 HID lamps produce high intensity light. Do not look directly at the ligh\
t 
coming from the lamp housing, or the lens, or allow items such as 
magnifying lenses to be placed in the light path. This could result in 
serious eye damage.
 Do not touch the ventilation outlets, as they will become hot in use.
 Do not cover or obstruct the ventilation outlets or inlets.
 Do not cover the lens whilst the projector is switched on. This could 
cause a fire
 Always allow the projector to cool for 5 minutes before disconnecting 
the power, moving the projector or changing the lamp.
 Never use strong detergents or solvents such as alcohol or thinners to 
clean the projector and lens.
Notes 
						

							
Rev A December 2010 Page vii
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual Important Information

Installation precautions
 The projector must be installed only by suitably qualified personnel, in\
 
accordance with local building codes.
  The projector should be installed as close to the power outlet as 
possible.
 The power connection should be easily accessible, so that it can be 
disconnected in an emergency.
 Ensure that there is at least 30cm (12in) of space between the 
ventilation outlets and any wall, and 10cm (4in) on all other sides.
 Do not install the projector close to anything that might be affected by\
 
its operational heat, for instance, polystyrene ceiling tiles, curtains \
etc.
 The projector weighs approximately 13 kg (29 lbs). Use safe handling 
techniques when lifting the projector.
 Do not stack more than three projectors.
 When stacking projectors, the stack MUST be vertical, to ensure that 
the stresses are distributed to all four chassis corners.
 Before installation, make sure that the surface, ceiling or rigging that\
 is 
to support the projector is capable of supporting the combined weight 
of all the projectors.
 Backup safety chains or wires should always be used with ceiling 
mount installations.
 Do not place heavy objects on top of the projector chassis. Only the 
chassis corners are capable of withstanding the weight of another 
projector.
 Do not drop or knock the projector.
 Place the projector in a dry area away from sources of dust, moisture, 
steam, smoke, sunlight or heat.
 Do not tilt the projector more than  ±12° in either direction when\
 in use, 
as this may cause serious lamp failure, damage the lamp module and 
cause extra cost on replacement.
Operation and configuration precautions
 Software update should NOT be carried out except by, or with the 
supervision of, Digital Projection Service personnel.
Notes
±12°
±12° 
						

							
Page viii Rev A December 2010
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

NotesCompliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 35 dB (A) according to ISO 3744 \
or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications o\
r 
changes to the unit EXCEPT those specified by Digital Projection in this manual. 
Failure to comply with this government regulation could void your right \
to operate 
this equipment.
This equipment has been tested and found to comply with the limits for a\
 Class B 
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference when the e\
quipment 
is operated in a residential environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accorda\
nce with the 
instruction manual, may cause harmful interference to radio communicatio\
ns.
European Waste Electrical and Electronic Equipment 
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and 
Electronic Equipment. Our products are designed with reuse, recycling 
and recovery of all components in mind. To this end, at end of life, your 
projector may be returned to Digital Projection Ltd or its agent so that\
 the 
environmental impact can be minimised. 
						

							
Rev A December 2010 Page ix
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual Important Information

Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: as above
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email [email protected], [email protected]
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email  [email protected]
Web Site www.digitalprojection.com
Notes 
						

							
Page x Rev A December 2010
Important Information Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual