Digital Projection M-vision Cine 400 3d Series User Guides

							Digital Projection M-Vision Cine 400 3D seriesOPERATING THE PROJECTORInstallation and Quick-Start Guide
Revision A, May 2012 
Operating the projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. The projector begins a self-test.
2. When the self-test has completed, the power indicator on the projector control panel shows blue to indicate that the\
 projector is in 
STANDBY mode and the lamp is switched off. Press and hold for three seconds either of the following:
 ●The POWER button on the control panel
 ●The ON button  on the remote control
The power indicator on the control panel flashes blue for a few seconds whilst the lamp comes up to full brightness. When the projector is 
fully switched on and ready for use, the power indicator switches off.
Switching the projector off
1. Press POWER on the control panel or the POWER button  on the remote control, then press the button again to confirm.
The lamp will switch off, the power indicator on the control panel will start flashing in blue and the projector will be in STANDBY mode 
while cooling off.
2. Wait until the power indicator has stopped flashing and the fans have stopped working, then disconnect the power cable.
Notes
For full details of how to use the 
controls and the menu system, see 
the Operating Guide.
Even if the power indicator has 
stopped flashing, please allow 
the lamp to cool off for five 
minutes before:
 ●disconnecting the power
 ●moving the projector
 ●changing the lamp
Inst-07 
						

							Digital Projection M-Vision Cine 400 3D seriesOPERATING THE PROJECTORInstallation and Quick-Start Guide
Revision A, May 2012 
Adjusting the lens
Zoom
Turn the smooth ring on the lens, closest to the case, to adjust the zoom so that the image fills the screen.
Focus
Turn the knurled ring at the outer end of the lens, to adjust the focus u\
ntil the image is sharp.
Shift
1. To reveal the adjustment access holes, slide the Digital Projection badge\
 in the direction shown below, then gently lift it off by hand.
2. Use the 5mm Allen wrench to adjust the horizontal and vertical position of the image\
. 
Notes
Do NOT prise off the badge 
using a tool.
Lens shift controls are not available 
on projectors fitted with the fixed 
0.73:1 lens.
Inst-08
Horizontal shiftVertical shift 
						

							Digital Projection M-Vision Cine 400 3D seriesOPERATING THE PROJECTORInstallation and Quick-Start Guide
Revision A, May 2012 
Selecting an input signal or test pattern
Input signal
Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within 
two or three seconds.
If more than one signal is connected, select the image you want to displ\
ay in one of the following ways:
 ●Access the Main menu (either from the remote control or from the control panel) and t\
hen go to Input Select.
 ●On the remote control, select from the inputs using the number buttons 1 to 6
 ●On the control panel, press SOURCE to cycle through all the inputs.
Test pattern
If you have no image source connected to the projector, you can display a test pattern instead. To display a test pattern, do either of the 
following:
 ●Press the TEST button TEST on the remote control to cycle through all test patterns.
 ●Access the Service menu and select a test pattern.
Notes
For full details of how to use the 
controls and the menu system, 
see the Operating Guide.
Inst-09 
						

							Digital Projection M-Vision Cine 400 3D seriesOPERATING THE PROJECTORInstallation and Quick-Start Guide
Revision A, May 2012 
Adjusting the image
Orientation
To change the image orientation, access the System menu and then open the Rear Projection and Ceiling Mode settings.
Aspect ratio
To set up an aspect ratio for your image, do either of the following:
 ●Press the ASPECT RATIO button on the remote control to cycle through the available settings.
 ●Access the Main menu and then select the Aspect Ratio setting.
Picture
To change brightness and contrast, do either of the following:
 ●Press BRIGHTNESS  or CONTRAST  on the remote control, then use the arrow buttons to move the sliders.
 ●Access the Image menu and adjust the Brightness and Contrast settings.
3D
In the Main menu, use the 3D Control sub-menu.
Notes
For full details of how to use the 
controls and the menu system, 
see the Operating Guide.
Inst-10 
						

							M-Vision Cine 400 3D series
High Brightness Digital Video Projector
16:9 widescreen display
Revision A, May 2012 112-855A
CONNECTION GUIDE 
						

							Digital Projection M-Vision Cine 400 3D series Connection Guide
Revision A, May 2012 
CONTENTS
Important information ............................................................Con-01
Symbols used in this guide ........................................................................\
.....Con-01
Special formatting ........................................................................\
....................Con-01
Product revision ........................................................................\
.......................Con-01
Signal inputs ........................................................................\
...Con-02
Component 1 and 2 ........................................................................\
..................Con-02
RGsB ........................................................................\
...............................Con-02
YPbPr/YCbCr ........................................................................\
..................Con-02
RGB  ........................................................................\
...........................................Con-02
HDMI 1 and 2 ........................................................................\
.............................Con-02
Supported signal input modes ..............................................Con-03
Control connections ...............................................................Con-06
Service port........................................................................\
...............................Con-06
LAN and RS232 ........................................................................\
.........................Con-06
Wired remote control ........................................................................\
...............Con-06
Trigger 1 and 2 outputs ........................................................................\
............Con-06
3D Sync ........................................................................\
.....................................Con-06
LAN IP configuration utility ...................................................Con-07
Wiring details ........................................................................\
..Con-08
Signal inputs  ........................................................................\
.............................Con-08
Component 1........................................................................\
...................Con-08
Component 2........................................................................\
...................Con-08
RGB input........................................................................\
........................Con-08
HDMI inputs ........................................................................\
....................Con-09
Control connections ........................................................................\
................Con-10
Wired remote control connection ............................................................Con-10
Serial control input ........................................................................\
..........Con-10
Trigger 1 & 2 outputs ........................................................................\
.......Con-10
LAN connection ........................................................................\
...............Con-11
3D sync connection ........................................................................\
.........Con-11 
						

							Digital Projection M-Vision Cine 400 3D seriesIMPORTANT INFORMATIONConnection Guide
Revision A, May 2012 Con-01
Important information
Symbols used in this guide
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
FURTHER INFORMATION
This symbol shows important additional information.
Special formatting
 ●Buttons on the projector control panel or the remote control appear in BLOCK CAPITALS, e.g. MENU. Where necessary, the name of a button is followed by an image, e.g. ON .
 ●Menu titles and menu items appear in Bold, e.g. the System menu.
 ●If the described state of the equipment is named, the state appears in C\
APITALS, e.g. STANDBY mode.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice. 
						

							Digital Projection M-Vision Cine 400 3D seriesSIGNAL INPUTSConnection Guide
Revision A, May 2012 
Signal inputs
Component 1 and 2
RGsB
In the Advanced Image menu, set Colorspace to Auto, or if necessary to 
RGB Video.
YPbPr/YCbCr
In the Advanced Image menu, set Colorspace to Auto, or if necessary to 
REC709 or REC601.
RGB
In the Advanced Image menu, set Colorspace to Auto, or if necessary to 
RGB PC.
HDMI 1 and 2
If you are using a Dual Pipe 3D signal, connect the left signal to one input 
and the right signal to the other.
If necessary, the images can be swapped using the 3D Settings sub-menu 
of the Main menu.
Notes
For a complete listing of pin 
configurations for all signal and 
control connectors, see Wiring 
Details later in this guide.
The projector does not support 
RGBS.
Con-02
RGB
Component 1
Component 2HDMI 2HDMI 1 
						

							Digital Projection M-Vision Cine 400 3D seriesSUPPORTED SIGNAL INPUT MODESConnection Guide
Revision A, May 2012 
Supported signal input modes
SignalResolutionFrame Rate 
(Hz)
3D Support
ComponentVGA RGBHVVGA YUVHDMI RGBHDMI YUV 8 bitHDMI YUV 10 bitHDMI YUV 12 bit
Frame PackingSide by Side (Horizontal)Top and Bottom
PC
640 x 48059.94
640 x 48074.99
640 x 48085
800 x 60060.32
800 x 60075
800 x 60085.06
848 x 48047.95
848 x 48059.94
1024 x 76860
1024 x 76875.03
1024 x 76885.03
1024 x 76870.1
1280 x 72047.95
1280 x 76860
1280 x 76860
1280 x 76875
1280 x 76885
1280 x 80050
1280 x 80060
1280 x 80075
1280 x 102460.02
1280 x 102475.02
1280 x 102485.02
1440 x 90060
Con-03
continued on next page... 
						

							Digital Projection M-Vision Cine 400 3D seriesSUPPORTED SIGNAL INPUT MODESConnection Guide
Revision A, May 2012 
SignalResolutionFrame Rate 
(Hz)
3D Support
ComponentVGA RGBHVVGA YUVHDMI RGBHDMI YUV 8 bitHDMI YUV 10 bitHDMI YUV 12 bit
Frame PackingSide by Side (Horizontal)Top and Bottom
PC (continued)
1440 x 90075
1400 x 105060
1400 x 105075
1600 x 120060
1920 x 108047.95
1600 x 120060
1920 x 120060
1680 x 105059.94
Apple Mac
640 x 48066.59
832 x 62474.54
480i59.94
576i50
EDTV480p59.94
576p50
Con-04
continued on next page...