Digital Projection M-vision Cine 3d Connection Guide

							
Digital Projection M-Vision Cine 3D series  WIRING DETAILS  Connection Guide
Page 9Rev A  August 2011
Control connections
Wired Remote control connection
3.mm mini jack
Tip.Power
Ring.Signal
Sleeve.Ground
Serial control input
1.unused
2.Received.Data.(RX)
3.Transmitted.Data.(TX)
4.unused
5.Signal.Ground
6.unused
7.unused
8.unused
9.unused
Null-modem cable
(used.to.connect.the.projector.to.a.computer)
RX.2.---.3.TX
TX.3.---.2.RX
GND.5.---.5.GND
Notes
 Note that plugging in the remote 
control cable will disable the infra-
red.
 Only one remote connection should 
be used at any one time.
 The projector is a DTE, so use:
  a straight cable to connect to a 
modem, or
 a null-modem cable as shown here 
to connect to another DTE such as a 
computer.
 Trigger outputs are normally at 0V, 
and rise to +12V when triggered.
Sleeve
Ring
Tip
SleeveTip
Serial port settings
Baud.rate. 9,600.bps
Data.length.8.bits
Stop.bits..one
Parity. .none
Flow.control.none
pin view of female connector
Trigger 1 & 2 outputs
3.mm mini jack
Tip.Signal
Sleeve.Ground 
						

							12
English
3139 115 21261
Optional Connections
The optional equipment and connecting cords
are not supplied.  Refer to the operating
instructions of the connected equipment for
details.
Line Out Connection
Connect this output to any analog audio
equipment for playback or recording (CD
recorder, tape recorder or amplifier for example).
Use a cinch cable to connect the LINE OUT
terminals to the analog audio in terminals of the
equipment.
Connecting other equipment to your
system
Connect the audio left and right OUT terminals
of a  TV, VCR, Laser Disc player, DVD player or
CD Recorder to the AUX/CDR IN terminals.
Notes:
–Do not connect equipment to both the LINE
OUT and AUX/CDR IN terminals at the same time.
Otherwise, noise will be generated and malfunction
might occur.
–If you are connecting equipment with a mono
output (a single audio out terminal), connect it to
the AUX/CDR IN left terminal.  Alternatively, you
can use a “single to double” cinch cable (still be
mono sound).
Digital Out Connection
Connect this digital output when recording on
any audio equipment with digital input (CD
Recorder, Digital Audio Tape [DAT] deck, Digital
to Analog Conver ter and Digital Signal Processor,
for example).  Use a cinch cable to connect the
DIGITAL OUT terminal to the digital input
terminal of the equipment.
Inserting batteries into the
Remote Control
Inser t two batteries (Type R06 or AA) into the
remote control with the correct polarity as
indicated by the + and - symbols inside the
batter y compar tment.
1 2
CAUTION!
–Remove batteries if they are exhausted
or not to be used for a long time.
–Do not use old and new or different
types of batteries in combination.
–Batteries contain chemical substances, so
they should be disposed off properly.
Preparations
pg 001-032/C798/37-Eng 4/16/02, 6:38 PM12 
						

							13
English
3139 115 21261
Controls (main system’s illustration on page 3)
Controls on the system and
remote control
1
ECO POWER
– to switch the system on or to Eco Power
Standby mode.
2STANDBY ON y
– to switch the system on or to Standby mode.
3DISPLAY SCREEN
– to view the current status of the system.
4DISC TRAY
5DISC CHANGE
– to change disc(s).
6DISC 1 / DISC 2 / DISC 3 (CD DIRECT)
– to select a disc tray for playback.
7OPEN•CLOSE
– to open or close the disc tray.
8INTERACTIVE VU  METER
– to show the VU (volume unit) meter in music or
volume mode depending on the display mode
selected.
9VOLUME
– to increase or decrease the volume.
0Tape Deck Operation
AUTO REPLAY (AUTO RE.)
– to select continuous playback in either AUTO
PLAY or ONCE mode only.
DUBBING
– to dub a tape.
REC
– to star t recording on tape deck 2.
!SOUND NAVIGATION
– to select the desired sound feature : DSC or
VAC .
@JOG CONTROL
– to select the desired sound effect for the
selected sound feature.
DSC ..................DIGITAL, ROCK, POP, NEWAGE,
CLASSIC or ELECTRIC .
VAC ..................HALL, CONCERT, CINEMA,
DISCO, ARCADE or CYBER.
#INCREDIBLE SURROUND (IS)
– to activate or deactivate the surround sound
effect.
$wOOx ON•OFF
– to select enhanced or normal wOOx sound
effect.
wOOx LEVEL
– to select desired wOOx level :  WOOX 1,
WOOX 2 or WOOX 3.
%ç
– to open the tape deck door.
^TAPE DECK 2
&TAPE DECK 1
*SOURCE – to select the following:
CD / (CD 1•2•3)
– to select disc tray 1, 2 or 3.
TUNER / (FM•AM)
– to select waveband : FM or AM.
TAPE / (TAPE 1• 2)
– to select tape deck 1 or 2.
AUX / (CDR/DVD)
– to select a connected external source :
CDR/DVD or AUX (auxiliar y) mode.
(n
– to connect headphones.
)Mode Selection
PLAY PAUSE ÉÅ
for CD ................. to star t or interrupt playback.
for TAPE .............. to star t playback.
for PLUG & PLAY…(on the system only) to
initiate and star t plug & play
mode.
SEARCH• TUNING à   á
for CD ................. to search backward/forward.
for TUNER......... to tune to a lower or higher radio
frequency.
for TAPE .............. to rewind or fast forward.
for CLOCK .......(on the system only) to set the
hour.
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM13 
						

							14
English
3139 115 21261
Controls
*
≤
¡
0
9
)
§
º
ª
•
)
9
™
≥
@
6
∞
#
$
@
DEMOªSTOP/CLEARªÇ
for CD ................. to stop playback or to clear a
program.
for TUNER ........ to stop programming.
.................................(on the system only) to delete the
preset radio station.
for TAPE .............. to stop playback or recording.
................................. to reset tape counter number.
for DEMO .........(on the system only) to activate/
deactivate the demonstration.
for CLOCK .......(on the system only) to exit clock
setting or cancel timer.
for PLUG & PLAY…(on the system only) to exit
plug & play mode.
PREV / PRESET / NEXT í  ë
for CD ................. to skip to the beginning of the
current, previous, or next track.
for TUNER ........ to select a preset radio station.
for CLOCK .......(on the system only) to set the
minute.
¡DISPLAY
– to select different screen display mode :
NORMAL, MODE 1, MODE 2, or MODE 3.
™PROG (PROGRAM)
for CD ................. to program disc tracks.
for TUNER ........ to program preset radio stations.
for CLOCK .......(on the system only) to select 12-
or 24-hour clock mode.
£CLOCK•TIMER
– to view the clock, set the clock or set the timer.
≤MUTE
– to interrupt or resume sound reproduction.
∞CLOCK
– to view the clock display.
§REPEAT
– to playback track(s)/disc(s)/program repeatedly.
≥SHUFFLE
– to playback all available discs and their tracks/
program in random order.
•TIMER ON/OFF
– to activate or deactivate the timer.
ªSLEEP
– to activate, deactivate or set the sleep timer.
ºB
– to switch the system to Standby mode.
– to switch the system to Eco Power Standby
mode.Notes for remote control:
–First, select the source you wish to
control by pressing one of the source select
keys on the remote control (CD 123 or
TUNER, for example).
–Then select the desired function (É, í,
ë, for example).
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM14 
						

							15
English
3139 115 21261
Basic Functions
IMPORTANT!
Before you operate the system, complete
the preparation procedures.
Plug and Play
Plug and Play allows you to store all available
radio stations automatically.
If Plug and Play has not been installed
1When you turn on the system, "AUTO
INSTALL - PRESS PLAY" will be displayed.
2Press PLAYÉ on the system to star t
installation.
➜"INSTALL" will be displayed and followed by
"TUNER" and then "AUTO".
➜
PROG will star t flashing.
➜The system will search for all radio stations
on the FM band, then the AM band.
➜All available radio stations with sufficient signal
strength will be stored automatically.
➜The system will stop searching when all the
available radio stations are stored or when the
memor y for 40 preset radio stations is used.
➜The last preset radio station will play when
Plug and Play is completed.
To reinstall Plug and Play
1In Standby or Demonstration mode, press and
hold PLAYÉ on the system until "AUTO
INSTALL - PRESS PLAY" is displayed.
2Press PLAYÉ again to star t installation.
➜All previously stored radio stations will be
replaced.To exit without storing the Plug and Play

Press Çon the system.
Notes:
–When the power is turned on, the disc tray may
open and close to initialize the system.
–If you do not complete Plug and Play installation,
Plug and Play will be reinitiated the next time you
turn on the power.
–If no stereo frequency is detected during
Plug and Play, CHECK ANTENNA will be
displayed.
–During Plug and Play, if no button is pressed
within 15 seconds, the system will exit Plug and
Play mode automatically.
Demonstration mode
The system has a demonstration mode that
shows the various features offered by the system.
To activate the demonstration

In Standby mode, press and hold DEMO
STOPÇon the system until "DEMO ON" is
displayed.
➜The demonstration will begin.
To deactivate the demonstration

Press and hold DEMO STOP Çon the system
until "DEMO OFF" is displayed.
➜The system will switch to Standby mode.
Note:
–Even if you remove the AC power cord and
reconnect it to the wall socket, the demonstration
will remain off until you activate it again.
FW- MINI HIFI SYSTEM
ECO POWER
CD 1•2•3
FM•AM
CDR / DVD
TAPE 1•2
PROGDUBBING REC CLOCK•
TIMERAUTO
REPLAY
STANDBY- ON
MUSIC LEVELINTERACTIVE VU METERVOLUMEVOLUME
PREVPRESETNEXTDEMO
STOP/
CLEARPLAY•
PAUSESEARCH•TUNING
CDTUNER
TAPE AUX
DISPLAY
ON•OFF LEVELWO OX
SOUNDNAVIGATION - JOG
SOURCE
WOOX
DYNAMIC
AMPLIFICATION
CONTROL
SURROUNDVAC
DSC
INCREDIBLE
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM15 
						

							16
English
3139 115 21261
Switching the system on
In Standby/Demonstration mode

Press STANDBY ON.
➜The system will switch to the last selected
source.

Press CD, TUNER, TAPE, AUX (or CD 123,
TUNER, TAPE 1/2 or AUX/CDR on the
remote control).
➜The system will switch to the selected source.

Press any one of the DISC DIRECT PLAY
buttons.
➜The system will switch to CD mode.
In Eco Power Standby mode

Press ECO POWER.
➜The system will switch to last selected source.

Press CD 123, TUNER, TAPE 1/2 or AUX/
CDR on the remote control.
➜The system will switch to the selected source.
Switching the system to Standby
mode
In Demonstration mode

Press and hold DEMO STOP Ç on the
system.
In any other source mode (except Eco
Power Standby mode)

Press STANDBY ON (or B on the remote
control).
➜The clock will appear on the display when the
system is in Standby mode.
Switching the system to Eco
Power Standby mode (< 1 Watt)

Press ECO POWER (or press and hold B on
the remote control).
➜"ECO POWER" will be displayed, then the
display screen will go blank.
➜The low power ECO POWER LED will be
lighted.
Note:
–If you have not deactivated the demonstration, it
will resume five seconds after the system switches
to Eco Power Standby or Standby mode.
Power Saving Automatic Standby
As a power-saving feature, the system will
automatically switch to Standby mode if you do
not press any buttons within 30 minutes after a
disc or tape has stopped playing.
Display mode
There are four different display modes for
selection.

Press DISPLAY repeatedly to select NORMAL,
MODE 1, MODE 2, or MODE 3.
NORMAL ........All available LEDs will light up
and the display screen will have
full brightness.  The VU meter will
be in music mode.
MODE 1 ..........All available LEDs will light up
and the display screen will have
full brightness.  The VU meter will
be in volume mode.
MODE 2 ..........All available LEDs will light up
and the display screen will be at
half brightness.  The VU meter
will be in music mode.
MODE 3 ..........The display screen will be at half
brightness.  The VU meter and all
LEDs will be off.
Volume Control
Adjust VOLUME to increase (turn knob
clockwise or press VOLUME +) or decrease
(turn knob counter-clockwise or press
VOLUME -) the sound level.
To listen through the headphones

Connect the headphones plug to the n socket
at the front of the system.
➜The speakers will be muted.
To switch off the volume temporarily

Press MUTE on the remote control.
➜Playback will continue without sound and
"MUTE" will be displayed.

To restore the volume, press MUTE again or
increase the VOLUME level.
Basic Functions
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM16 
						

							17
English
3139 115 21261
Sound Navigation
For optimal sound listening, select only one
of the following navigation sound controls
at a time : wOOx, DSC or VAC .
wOOx
There are three wOOx settings to enhance the
bass response.
1Press wOOx ON•OFF to
switch ON (enhanced) or OFF
(normal) the wOOx sound
effect.

When wOOx is switched on;
➜
WO OX and the last selected
wOOx level will appear on the display.

When wOOx is switched off;
➜The display will show "WOOX NORM" and
WO OX will disappear from the display.2When wOOx is switched on, adjust wOOx
LEVEL (or press wOOx LEVEL on the
remote control) to select the desired wOOx
level: WOOX 1, WOOX 2 or WOOX 3.
Note:
–Some discs or tapes might be recorded in high
modulation, which causes a distortion at high
volume. If this occurs, deactivate wOOx or reduce
the volume.
DSC (Digital Sound Control)
The DSC feature enables you to adjust the
system to suit your type of music.
1Press DSC.
➜DSC button lights up
2Adjust the JOG
CONTROL (or press
DSC on the remote
control repeatedly) to select
the desired Digital Sound
Control effect : DIGITAL, ROCK, POP, NEWAGE,
CLASSIC or ELECTRIC .
➜The selected DSC will be highlighted.
Note:
–For a neutral sound effect, select CLASSIC .
VAC (Virtual Ambience Control)
The VAC feature enables you to adjust the
system to select a type of environment.
1Press VAC.
➜VAC button lights up.
2Adjust the JOG
CONTROL (or press
VAC  on the remote
control repeatedly) to
select the desired Vir tual
Ambience Control effect : HALL, CONCERT,
CINEMA, DISCO, ARCADE or CYBER.
➜The selected VAC will be highlighted.
Note:
–When you select VAC, Incredible Surround will
switch on automatically.
Automatic DSC-wOOx / VAC-wOOx
selection
The best wOOx setting is generated
automatically for each DSC or VAC selection.
You can manually select the wOOx setting that
best suits your listening environment.
Incredible Surround
The Incredible Surround magnifies the vir tual
distance between the front speakers for an
incredibly wide, enveloping, stereo effect.

Press INCREDIBLE
SURROUND (or IS on
the remote control)
repeatedly to activate/
deactivate the surround
sound effect.
➜If activated, 
will appear on the display and the INCREDIBLE
SURROUND button lights up.
➜If deactivated, “IS OFF” will be displayed.
Basic Functions
SURROUNDVAC
DSC
INCREDIBLE
SURROUNDVAC
DSC
INCREDIBLE
SURROUNDVAC
DSC
INCREDIBLE
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM17 
						

							18
English
3139 115 21261
CD Operation
FW- MINI HIFI SYSTEM
DISC
CHANGEOPEN•
CLOSE
D C3CHANGER
ECO POWER
CD 1•2•3
FM •AM
CDR / DVD
TAPE 1•2
PROGDUBBING REC CLOCK•
TIMERAUTO
REPLAY
STANDBY- ON
3 DISC DIRECT PLAYDISC 3
CD SYNCHRO RECORDINGCD / CD-
R/CD-
RW COMPATIBLE
MUSIC LEVELINTERACTIVE VU METERVOLUMEVOLUME
PREVPRESETNEXTDEMO
STOP/
CLEARPLAY•
PAUSESEARCH•TUNING
DISC 2DISC 1
CDTUNER
TAPE AUX
DISPLAY
ON•OFF LEVELWO OX
SOUNDNAVIGATION - JOG
SOURCE
WOOX
DYNAMIC
AMPLIFICATION
CONTROL
SURROUNDVAC
DSC
INCREDIBLE
IMPORTANT!
–This system is designed for regular discs.
Therefore, do not use any accessories such
as disc stabilizer rings or disc treatment
sheets, etc., as offered on the market,
because they may jam the changer
mechanism.
–Do not load more than one disc into
each tray.
Discs for Playback
This system can playback all digital audio CD,
finalized digital audio CD-Recordable (CDR)
discs and finalized digital audio CD-Rewritable
(CDRW)discs.
Loading Discs
1
Press CD to select CD mode.
2Press OPEN•CLOSE to open the disc tray.3Load up to two discs on the individual disc trays.
To load the third disc, press DISC CHANGE.
➜The disc tray will rotate until the empty tray
is ready for loading.
3CD CHANGER
CLOCK.TIMERVOLUMEDEMOPRESET TUNINGSHUFFLE
TIMERPLAY    
MODE
SIDESET CLOCKTIMER SETBANDRECORDDUBBINGCD    TAPEPROGRAM
CLEARRDS
MODE1
2
3TIMER DBB PROGRAMAMPMSHUFFLEFMMW
LW SW
STEREONRFRONT
BACKRECORD
HSD2
21
OPEN•CLOSE
1
4Press OPEN•CLOSE to close the disc tray.
➜"READING" will be displayed.  The selected
disc tray, total number of tracks and the playing
time will appear on the display.
➜A lighted button indicates that a disc is loaded
in the disc tray.
Notes:
–Load the discs with the label side facing up.
–To ensure good system performance, wait until
the disc tray completely reads the disc(s) before
proceeding.
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM18 
						

							19
English
3139 115 21261
CD Operation
Disc Playback
a disc is loaded in the disc tray
the current selected disc tray is empty
the current selected disc tray is loaded 
or playing
To playback all discs on the disc tray

Press PLAYÉ.
➜All the available discs will playback once, then
stop.
➜During playback, the selected disc tray, track
number and elapsed playing time of the current
track will appear on the display.
To playback one disc only

Press the DISC DIRECT PLAY button : DISC 1,
DISC 2 or DISC 3.
➜The selected disc will playback once, then
stop.
To interrupt playback

Press PAUSEÅ.

To resume playback, press PLAYÉ again.
To stop playback

Press Ç.
To search for a particular passage during
playback

Press and hold à or á and release it when
the desired passage is located.
➜During searching, the volume will be reduced.
To select a desired track

Press í or ë repeatedly until the desired
track appears on the display.

If playback is stopped, press PLAYÉ to star t
playback.
Note:
–In Shuffle mode, pressingí will cause the
player to skip only to the beginning of the current
track.
To skip to the beginning of the current
track during playback

Press í once.Replace discs during playback
1Press DISC CHANGE.2To change the inner disc, press DISC
CHANGE again.
➜"DISC CHANGE" will be displayed and the
disc will stop playing.
➜The disc tray will close to retrieve the inner
disc, then reopen with the inner disc accessible.
Programming the disc tracks
Programming tracks is possible when playback is
stopped. Up to 40 tracks can be stored in the
memor y in any order.
1Load the desired discs on the disc tray (refer to
“Loading Discs”).
2Press PROG to star t programming.
➜PROG will star t flashing.
3Press CD (CD 1•2•3) or DISC 1/2/3 button
to select a disc.
4Press í or ë repeatedly to select the desired
track.
5Press PROG to store the track.
¶Repeat steps 3–5 to store other discs and
tracks.
6Press PLAYÉ to star t program playback.
➜"PLAY PROGRAM" will be displayed.

To end programming without star ting playback,
press Ç once .
➜The total number of tracks programmed and
the total playing time will appear on the display.
Notes:
–If the total playing time is more than 
99:59
or if one of the programmed tracks has a number
greater than 30, then 
--:-- will appear on the
display instead of the total playing time.
–If you attempt to program more than 40 tracks,
PROGRAM FULL will be displayed.
–If you press any of the DISC DIRECT PLAY
buttons, the system will playback the selected disc
or track, and the stored program will be ignored
temporarily. The 
PROG symbol also will disappear
temporarily from the display. It will reappear when
playback of the selected disc ends.
–During programming, if no button is pressed
within 20 seconds, the system will exit the Program
mode automatically.
pg 001-032/C798/37-Eng 4/16/02, 6:39 PM19 
						

							20
English
3139 115 21261 To review the program

Stop playback and press í or ë repeatedly.

To exit review mode, press Ç.
To erase the entire program

Press Ç once when playback is stopped or
twice during playback.
➜"PROGRAM CLEARED" will be displayed.
➜
PROG will disappear from the display.
Note:
–The program will be erased when the system is
disconnected from the power supply or when the
disc tray is opened.
Repeat
The current track, a disc, all available discs or all
programmed tracks can be played repeatedly.
1Press REPEAT on the remote control
repeatedly to select various repeat modes.

In normal playback
➜"TRACK" – to repeat the current track.
"DISC" – to repeat the entire disc.
"ALL DISC" – to repeat all available discs.
➜
RPT  appears on the display.

In program playback
➜"TRACK" – to repeat the current
programmed track.
"PROGRAM" – to repeat all programmed
tracks.
➜
RPT  and PROG will appear on the display.

The selected track/disc(s)/program will now be
played repeatedly until you press Ç.
2To resume normal playback, press REPEAT
until the "OFF" mode is displayed.
➜
RPT  will disappear from the display.
Note:
–Selecting SHUFFLE during repeat playback will
cancel all repeat modes.
CD Operation
Shuffle
All the available discs and their tracks or all the
programmed tracks can be played in random
order.
1Press SHUFFLE on the remote control.
➜"SHUFFLE" and SHUFF  will appear on the
display.

The discs and the tracks will be played in
random order until you press Ç.
2To resume normal playback, press SHUFFLE
again.
➜
SHUFF  will disappear from the display.
When select REPEAT mode during
shuffling

In normal shuffled playback
➜"TRACK" and "ALL DISC" repeat modes are
available for selection.
➜
RPT  and SHUFF  will appear on the
display.

In program shuffled playback
➜"TRACK" or "PROGRAM" repeat modes are
available for selection.
➜
RPT , SHUFF  and PROG will appear on the
display.
For Recording, please refer to “Ta p e
Operation/Recording”.
pg 001-032/C798/37-Eng 4/16/02, 6:40 PM20