Digital Projection M-vision Cine 230, 260 Hb, Hc, M-vision Cine 400 User Manual

							
Rev A December 2010 Page 6.9
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 6. Appendix

Video formats supported
Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
PC640x480 59.94xxxVESA DMT 
640x480 74.99xxxVESA DMT 
640x480 85xxxVESA DMT 
800x600 60.32xxxVESA DMT 
800x600 75xxxVESA DMT 
800x600 85.06xxxVESA DMT 
848x480 47.95xxxVESA CVT 
848x480 59.94xxxVESA CVT 
1024x768 60xxxVESA DMT 
1024x768 75.03xxxVESA DMT 
1024x768 85.03xxxVESA DMT 
1024x768 70.1xxxVESA DMT 
1280x720 47.95xxxVESA GTF 
1280 x 768 60xxxVESA DMT 
1280 x 768 60xxxVESA DMT Reduced Blanking
1280 x 768 75xxxVESA DMT 
1280 x 768 85xxxVESA DMT 
1280 x 800 50x xxVESA DMT
1280 x 800 60xxxVESA DMT 
1280 x 800 75xxxVESA DMT 
1280x1024 60.02xxxVESA DMT 
1280x1024 75.02xxxVESA DMT 
1280x1024 85.02xxxVESA DMT 
1440 x 900 60xxxVESA DMT 
1440 x 900 75xxxVESA DMT 
1400 x 1050 60xxxVESA DMT 
1400 x 1050 75xxxVESA DMT 
1600x1200 60xxxVESA DMT 
1920x1080 47.95xxxVESA CVT 
1600 x 1200 60xxxVESA DMT 
1920 x 1200 60xxxVESA DMT Reduced Blanking 
1680x1050 59.94xxxVESA CVT 
Apple Mac 640x480 66.59xxxVESA DMT 
832x624 74.54xxxVESA DMT  
						

							
Page 6.10 Rev A December 2010
6. Appendix Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
NTSC NTSC (M, 4.43) 59.94x x ITU-R BT.1700, SMPTE 170M
PAL PAL (B,G,H,I) 50x x ITU-R BT.1700 
PAL (N) 50x x ITU-R BT.1700 
PAL (M) 59.94x x ITU-R BT.1700 
SECAM SECAM (M) 50x x ITU-R BT.1700 
480i 59.94xxxSMPTE 125M, CEA-861-D 
576i 50xxxITU-R BT.601, CEA-861-D 
EDTV 480p 59.94xxxxxSMPTE 293M, CEA-861-D 
576p 50xxxxxITU-R BT.1358, CEA-861-D 
HDTV 1035i 60xxxxxSMPTE 260M 
1080i 50xxxxxSMPTE 274M, CEA-861-D 
1080i (Aus) 50xxxxxSMPTE 295M 
1080i 59.94xxxxxSMPTE 274M, CEA-861-D 
1080i 60xxxxxSMPTE 274M, CEA-861-D 
720p 50xxxxxSMPTE 296M, CEA-861-D 
720p 59.94xxxxxSMPTE 296M, CEA-861-D 
720p 60xxxxxSMPTE 296M, CEA-861-D 
1080p 23.98xxxxxSMPTE 274M, CEA-861-D 
1080p 24xxxxxSMPTE 274M, CEA-861-D 
1080p 25xxxxxSMPTE 274M, CEA-861-D 
1080p 29.97xxxxxSMPTE 274M, CEA-861-D 
1080p 30xxxxxSMPTE 274M, CEA-861-D 
1080p 50xxxxxSMPTE 274M, CEA-861-D 
1080p 59.94xxxxxSMPTE 274M, CEA-861-D 
1080p 60xxxxxSMPTE 274M, CEA-861-D  
						

							
Rev A December 2010 Page 6.11
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 6. Appendix

NotesInput connections
HDMI 1 & 2 inputs
19 way type A connector
1 TMDS Data 2+
2 TMDS Data 2 Shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 Shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 Shield
9 TMDS Data 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 not connected
15 SCL (DDC Clock)
16 SCA (DDC Data)
17 DDC/CEC Ground
18 +5 V Power
19 Hot Plug Detect
Composite video input
1 x 75 ohm BNC
PAL or NTSC video
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
pin view of panel connector
pin view of female connector 
						

							
Page 6.12 Rev A December 2010
6. Appendix Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

pin view of female connector
RGB input
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Component 1 input
3 x RCA phono connectors
RGsB      YPbPr   YCbCr
Green + Sync     Y    Y
Blue      Pb   Cb
Red      Pr   Cr
RGBS
connect Sync to Video input
Component 2 input
3 x 75 ohm BNC
RGsB      YPbPr   YCbCr
Green + Sync     Y    Y
Blue      Pb   Cb
Red      Pr   Cr
Notes
 In most cases, the Auto setting 
will determine the correct color 
space to use. If it does not, 
you can select the appropriate 
setting manually. 
  To select between RGB and 
YPrPb signals, see Advanced 
Menu, in 4.Controlling the 
Projector. 
						

							
Rev A December 2010 Page 6.13
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 6. Appendix

Control connections
Wired Remote control connection
3.5mm mini jack
Tip  Power
Ring Signal
Sleeve Ground
Trigger 1 & 2 output
3.5mm mini jack
Tip  Signal
Sleeve Ground
Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a modem)
RX  2 --- 3 TX
TX 3 --- 2 RX
GND 5 --- 5 GND
Serial port settings
Baud rate  38400 bps
Data length 8 bits
Stop bits one
Parity none
Flow control none
•
•
•
•
•
Notes
 Trigger outputs are normally 
at 0V, and rise to +12V when 
triggered.
 The projector is a DCE, so use:
a straight cable to connect to a 
computer, or
a null-modem cable as shown 
here to connect to another DCE 
such as a modem.
•
•
Sleeve
Ring
Tip
SleeveTip
pin view of female connector 
						

							
Page 6.14 Rev A December 2010
6. Appendix Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Remote communications protocol
Introduction
The projector can be controlled by using an external control system or a\
 PC via an 
RS232 serial interface, using a terminal-emulation program, such as Hype\
rTerminal.
There are 2 types of commands:
Key commands
Operation commands
All commands consist of ascii text strings starting with 2 letters:
ky for key commands.
op for operations commands.
All commands end with an ascii Carriage Return character.
Key Commands
Key commands are used to simulate remote control key presses, and use th\
e 
following format:
ky  [CR]
Example
ky pow.on [CR] simulates the POWER ON key being pressed.
The commands
Code transmittedDescription
0x01pow.onTurn power on.
0x09pow.offTurn power off.
0x15menuBring up or cancel menu display.
0x17enterKeypad enter.
0x18cur.downKeypad down arrow.
0x1Acur.upKeypad up arrow.
0x1Dcur.leftKeypad left arrow.
0x1Fcur.righKeypad right arrow.
0x80brightBring up or cancel brightness slide bar.
0x81contrastBring up or cancel contrast slide bar.
•
•
•
•
Notes
 Details of how to connect to 
the projector, using the serial 
control input, can be found 
earlier in this section.
 Note: spaces in the commands 
are necessary.
  eg  ky pow.on 
NOT kypow.on 
						

							
Rev A December 2010 Page 6.15
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 6. Appendix

Code transmittedDescription
0x82sharpBring up or cancel sharpness slide bar.
0x83nrBring up or cancel noise reduction slide bar.
0x85gam.swSwitch to the next gamma value.
0x8Bsrc.1Switch the active source to source 1.
0x8Csrc.2Switch the active source to source 2.
0x8Dsrc.3Switch the active source to source 3.
0x8Esrc.4Switch the active source to source 4.
0x8Fsrc.5Switch the active source to source 5.
0x93osc.swSwitch to the next Overscan mode.
0x98mem.1Recall user memory associated with the User Memory A key.
0x99mem.2Recall user memory associated with the User Memory B key.
0x9Amem.3Recall user memory associated with the User Memory C key.
0x9Dasp.swSwitch to the next aspect ratio setting.
0xA3bcolor.swSwitch Brilliant Color on or off.
0xAActemp.swSwitch to the next colour temperature value.
0xADpattern.swSwitch to the next test pattern. 
						

							
Page 6.16 Rev A December 2010
6. Appendix Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Operation Commands
Operation commands are used to simulate menu operations and determine th\
e 
settings of the projector, and use the following format:
op   [CR]
The  string can take one of the following formats:
Description
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ascii text string.
Increment+Adds 1 to the current value.
Decrement-Subtracts 1 from the current value.
Execute(none)Performs an action.
Example
op aspect =1 [CR] sets the aspect ratio to Theaterscope.
op aspect ? [CR] asks what is the current aspect ratio.
op bright + [CR] increments the brightness setting.
op resync [CR] commands the projector to attempt to re-synchronise to the 
current input source.
The commands
OperationValuesNotes
aspect= ?0 = 16:9 
1 = Theaterscope 
2 = 4:3 
3 = 4:3 Narrow 
4 = Native
memory= ?0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D 
4 = Default
save.mem=0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D
bright= ? + -0 - 200
contrast= ? + -0 - 200
saturat= ? + -0 - 200
tint= ? + -0 - 200
sharp= ? + -0 - 200
noise.thresh= ? + -0 - 200
nr.simple= ? + -0 - 200
nr.mode= ?0 = Simple 
1 = Advanced
Notes
 Note: spaces in the commands 
are necessary.
  eg  op aspect=1 
NOT opaspect=1 
						

							
Rev A December 2010 Page 6.17
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 6. Appendix

OperationValuesNotes
nr.general= ? + -0 - 200
block.reduct= ? + -0 - 200
mosq.noise= ? + -0 - 200
overscan= ?0 = Off 
1 = Crop 
2 = Zoom
source.sel= ?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = YPrPb 2 
5 = S-Video 
6 = Video
resync(execute)
color.space= ?0 = Auto 
1 = YPbPr ( = REC709) 
2 = YCbCr ( = REC601) 
3 = RGB-PC 
4 = RGB-Video
video.stand= ?0 = Auto 
1 = NTSC 
2 = PAL 
3 = SECAM
gamma= ?0 = CRT 
1 = Film 
2 = Video 
3 = Punch 
4 = Graphics
color.temp= ?0 = 5500K 
1 = 6500K 
2 = 7500K 
3 = 9300K
dlp.frame= ?0 = Auto 
2 = 48 Hz 
3 = 50 Hz 
4 = 60 Hz
color.gamut= ?0 = Auto 
1 = REC709 
2 = SMPTE C 
3 = EBU 
4 = Native
bcolor= ?0 = Off 
1 = On
red.off= ? + -0-200
green.off= ? + -0-200
blue.off= ? + -0-200
red.gain= ? + -0-200
green.gain= ? + -0-200
blue.gain= ? + -0-200
vert.pos= ? + -0-200
horiz.pos= ? + -0-200 
						

							
Page 6.18 Rev A December 2010
6. Appendix Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

OperationValuesNotes
phase= ? + -0-200
tracking= ? + -0-200
sync.level= ? + -0-200
menu.pos= ?0 = Top left 
1 = Top right 
2 = Bottom left 
3 = Bottom right 
4 = Centre
blank.screen= ?0 = Black 
1 = Blue 
2 = White 
3 = Logo
auto.pow.off= ?0 = Off 
1 = On
auto.pow.on= ?0 = Off 
1 = On
rear.proj= ?0 = Off 
1 = On
ceil.mode= ?0 = Off 
1 = On
logo.disp= ?0 = Off 
1 = On
trig.1= ?0 = Screen 
1 = 16:9 
2 = Theaterscope 
3 = 4:3 
4 = 4:3 Narrow 
5 = RS232 
6 = On 
7 = Off
0: Trigger occurs when the projector is in 
RUNNING mode
trig.2= ?0 = Screen 
1 = 16:9 
2 = Theaterscope 
3 = 4:3 
4 = 4:3 Narrow 
5 = RS232 
6 = On 
7 = Off
0: Trigger occurs when the projector is in 
RUNNING mode
auto.source= ?0 = Off 
1 = On
model.name?
ser.number?
soft.version?
act.source?0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = YPrPb 2 
5 = S-video 
6 = Video
h.refresh?KHz
v.refresh?Hz