Digital Projection M-vision Cine 230, 260 Hb, Hc, M-vision Cine 400 User Manual

							
Rev A December 2010 Page 2.13
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Notes
 For more detailed information 
about using the menus, see 
section 4. Controlling the 
projector.
 Do not try to stack more than 
three projectors.
 When stacking projectors, 
the stack MUST be vertical, to 
ensure that the stresses are 
distributed to all four chassis 
corners.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors.
 Do not place heavy objects 
on top of the projector 
chassis. Only the chassis 
corners are capable of 
withstanding the weight of 
another projector.
 Backup safety chains or 
wires should always be 
used with ceiling mount 
installations.
  If the projector is fitted with the 
fixed 0.73:1 lens then there are 
no mechanical controls for lens 
shift.
Stacking projectors
The projector is capable of supporting the weight of up to three other p\
rojectors 
safely. The stack should be positioned vertically and perpendicular to the scree\
n, 
and the lens shift controls used to align the image with the screen, to \
maintain a 
geometrically correct image.
Carefully lower each projector down onto the top of the others, making s\
ure that 
they are vertically aligned with each other, and protected from becoming pushed 
over.
Align the images from the projectors, using the Lens shift controls on the top of 
the projector.
•
•
Level adjustment
If the projector is to be operated from a flat surface such as a project\
or table, then 
adjustment of projector level should be made by turning the four feet un\
der the 
chassis.
Ideally, the projector should be positioned perpendicular to the screen, and th\
e lens 
shift controls used to align the image with the screen, to maintain a ge\
ometrically 
correct image.
Rear projection
To use rear projection, set Rear Projection to On, in the System menu, to reverse 
the image.
In rear-screen applications where space behind the projector is limited,\
 a mirror may 
be used to fold the optical path. The position of the projector and mirror must be 
accurately set. If you are considering this type of installation, contac\
t your dealer for 
assistance 
						

							
Page 2.14 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  For more information about pin 
connections and control codes 
see section 6. Appendix.
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 & 2  HDCP-compliant digital video inputs from HDMI or DVI sources.
RGB  15 pin D-type VGA style input from personal computer
Component 1 RCA phono connectors for RGBS, (using Video input for sync) 
or YPbPr
Component 2 BNC connectors for YPbPr
Video  RCA phono connector for composite video 
or used as sync input for Component 1
S-Video standard 4 pin S-Video connector
Input connection examples
Component 2
HDMI 1HDMI 2RGB
Component 1VideoS-Video 
						

							
Rev A December 2010 Page 2.15
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Input connection examples, continued 
						

							
Page 2.16 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 
 For more information about pin 
connections and control codes 
see section 6. Appendix.
 For more information about the 
Trigger outputs see Control 
Menu in section 4. Controlling 
the projector.
Control connections
The following connections are available:
remote control
If infrared signals from the remote control cannot reach the projector d\
ue to 
excessive distance or obstructions such as walls or cabinet doors, you c\
an connect 
an external IR repeater to the Remote control input, and position its IR\
 sensor within 
range of the operator.
rS232 connection
All of the projector’s features can be controlled via a serial connection, using the text 
strings described in Remote communications protocol, in section 6. Appendix.
The RS232 connection can also be used to download the firmware updates, \
issued 
from time to time by Digital Projection.
Trigger 1 & 2
The Trigger 1 and Trigger 2 outputs are interchangeable:
Screen trigger:  can be connected to an electrically operated screen, 
automatically deploying the screen when the projector 
starts up, and retracting the screen when the projector 
shuts down.
Aspect Ratio trigger: can be used to control screen shuttering for different 
aspect ratios
Projector
Computer
RS232
Trigger 1Remote control
Trigger 2 
						

							
Rev A December 2010 Page 2.17
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Power connection
Lift the cable lock up, push the mains connector in firmly, then push the lock down to 
secure the cable.
Notes
 Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power 
connection 
						

							
Page 2.18 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 
						

							
Rev A December 2010  Page 3.1
3. Getting Started
Contents
Positioning the screen and projector ........................................................................\
....................3.2
Switching the projector on ........................................................................\
.......................................3.2
Inserting batteries into the remote control ........................................................................\
...........3.2
Selecting an input signal or test pattern ........................................................................\
...............3.3
Input ........................................................................\
........................................................................3.3
Test pattern ........................................................................\
..............................................................3.3
Adjusting the lens........................................................................\
.......................................................3.3
Zoom ........................................................................\
.......................................................................3.3
Focus ........................................................................\
......................................................................3.3
Shift ........................................................................\
.........................................................................3.3
Adjusting the projected image ........................................................................\
................................3.4
Aspect ratio ........................................................................\
..............................................................3.4
Image quality settings ........................................................................\
................................................3.4
Switching the projector off ........................................................................\
.......................................3.4 
						

							
Page 3.2 Rev A December 2010
3. Getting Started Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Switching the projector on
Connect the power cable between the mains supply and the projector.
Wait until the self-test has completed and the power indicator on the pro\
jector 
control panel shows steady blue. The lamp will be off and the projector will be in 
STANDBY mode.
Press POWER ON  on the remote control or POWER  on the projector 
control panel to switch the projector ON. The power indicator on the control 
panel will flash blue for approximately 30 seconds, whilst the projector\
 initialises. 
When the projector is ready for use, the power indicator will switch off.
•
•
Notes
 For more information about 
positioning the screen and 
projector, see Positioning 
the screen and projector, in 
section 2. of the User Manual: 
Installation.
 For more detailed information 
about:
  - using the control keys on the 
remote control or the projector 
control panel,
 - using the menus,
 see section 4. of the User 
Manual: Controlling the 
projector.
 If the red ISSUE indicator is 
illuminated continuously or 
flashing, see Error Codes in 
section 6 of the User Manual: 
Appendix, for more information
 Do not mix an old battery with 
a new one or different types of 
batteries.
 If you will not use the remote 
control for a long time, remove 
the batteries to avoid damage 
from battery leakage.
Inserting batteries into the remote control
Open the battery compartment and insert two AA size batteries, making sure 
they are inserted the correct way round, as shown below.
•
Positioning the screen and projector
Install the screen, ensuring that it is in the best position for viewing\
 by your 
audience.
Mount the projector, ensuring that it is at a suitable distance from the screen for 
the image to fill the screen, and that it is perpendicular to the sceen.\
•
•
Power 
connection
Projector 
control 
panel 
						

							
Rev A December 2010 Page 3.3
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 3. Getting Started

Selecting an input signal or test pattern
Input
Connect an video source to the projector. The signal should be automatically 
detected by the projector, and should be displayed within a two or three 
seconds.
If more than one signal is connected to the projector, then select which signal 
is to be displayed, using the  to   buttons on the remote control, or 
by pressing the SOURCE button on the projector control panel until the c\
orrect 
signal is displayed.
Test pattern
If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press  on the remote control, until the desired test pattern is displayed.
•
•
•
Notes
 For more information about 
connecting input signals, see 
Signal Inputs, in section 2. of 
the User Manual: Installation.
 For more detailed information 
about input connections, see 
Input signals in section 6. of 
the User Manual: Controlling 
the projector.
 For more information about lens 
shift, see Shifting the image in 
section 2. of the User Manual: 
Installation.
 If the projector is fitted with the 
fixed 0.73:1 lens then there are 
no mechanical controls for lens 
shift.
 Slide the badge in the 
direction shown below, then 
gently lift off by hand.
  Do NOT prise off using a tool.
Adjusting the lens
Zoom
Turn the smooth ring on the lens, closest to the case, to adjust the zoom\
 so that 
the image fills the screen.
Focus
Turn the knurled ring at the outer end of the lens, to adjust the focus u\
ntil the 
image is sharp.
Shift
Rotate the Digital Projection badge on top of the projector to reveal th\
e shift 
adjustment access holes. Use the 5mm allen wrench to adjust the horizont\
al and 
vertical position of the image.
•
•
•
Horizontal shift 
adjustment
Vertical shift 
adjustment
(Remove 
the badge)
Zoom 
ring
Focus 
ring 
						

							
Page 3.4 Rev A December 2010
3. Getting Started Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual
Adjusting the projected image
Aspect ratio
Press  on the remote control until the image is displayed in the corect aspect\
 
ratio.
Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
•
•
Notes
  For more detailed information 
about:
  - using all the control keys 
on the remote control or the 
projector control panel,
 - using the menus,
 see section 4. of the User 
Manual: Controlling the 
projector.
 For the picture setting 
adjustments shown here:
  - after 5 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the adjustment key must be 
pressed again.
 - to end the adjustment before 
5 seconds has elapsed, press 
a different adjustment key, or 
press the key again.
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power 
- moving the projector 
- changing the lamp
Switching the projector off
Press POWER OFF  on the remote control or POWER  on the 
projector control panel, then press the button a second time to confirm \
your 
intention to switch off. 
 
The lamp will switch off, and the power indicator on the control panel will flash 
blue for approximately 30 seconds until the lamp has cooled down.
Wait until the power indicator shows steady blue. The projector will now be in 
STANDBY mode.
Disconnect the power cable from the projector.
•
•
•