Digital Projection Lightning 35hd-T, 40hd-t User Manual
Have a look at the manual Digital Projection Lightning 35hd-T, 40hd-t User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
105-453B January 2007 Page 4.19 Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual 4. Using the Menus Notes The Image Orientation controls allow the projected image to be fl ipped for rear or refl ected projection, or to correct for incorrectly oriented images. DMD Image orientation Press the IMAGE ORIENTATION button on the Advanced image menu: Choose from: FLIP HORIZONTAL Horizontal inverts the image left to right for rear projection. FLIP VERTICAL Vertical inverts the image top to bottom for when the projector is mounted upside down. FLIP BOTH Both inverts the image left to right and top to bottom for rear projection and inverted operation. NORMAL Normal restores the image to its correct orientation. Flip vertical • • • •
Page 4.20 105-453B January 2007 4. Using the Menus Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual Notes The buttons of the Main menu are always visible at the bottom of the display. To go back to a previous menu option that is no longer visible, call up the menu again using the appropriate Main menu button. For information about how to connect the projector, see Connecting the projector in section 2. Installation, and Connections in section 6. Appendix. To control more than one projector from a single computer, either open a separate browser window for each projector, or set a bookmark for each projector in Favourites. Confi g menu Menu buttons... Networking confi g Detailed status Touchscreen calibration Reset IP addresses Confi guration menu Press the CONFIG button on the Main menu: Networking confi guration Press the NETWORK CONFIG button on the Confi g menu, then choose from: Ethernet confi guration choices You can use either the Ethernet #1 port or the Wireless LAN port to connect the projector to a controlling computer, but the two ports should always be set differently. If you are connecting a number of projectors and computers in a self contained network, then you should confi gure the IP address and Netmask settings as shown in the example on the next page. If you are connecting a single projector to a computer using a crossed LAN cable or Wireless LAN, then you should leave the IP address and Netmask settings at their default values. Confi gure the computer to match the projector, but with the last number of the IP address different. • • •
105-453B January 2007 Page 4.21 Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual 4. Using the Menus Notes Do not make changes to the networking confi guration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made. When making these settings, leading zeroes must be used for numbers less than 3 digits in length. eg 192.168.010.001 When making a network connection, eg via the address box in a browser, leading zeroes are not necessary. Confi g menu... Network confi guration... Ethernet #1 Settings... IP address Netmask Menu buttons... Confi gure wireless LAN Making the IP address and Netmask settings Press the IP ADDRESS fi eld. Use the on-screen keypad to enter the IP address, remembering to include leading zeroes for numbers less than 3 digits in length. The numbers will appear in the fi eld at the top of the keypad as you type. If you make a mistake, press DELETE to undo your typing one character at a time, or press CANCEL to start again completely. Press ENTER to transfer the completed address from the keypad display to the IP ADDRESS fi eld. repeat for NETMASK. When all settings are complete, double check, then press APPLY. Example To connect a number of projectors and computers in a self contained network, using a hub: For each projector and computer, set the fi rst three IP address number groups the same, and the last number different (any number between 001 and 254). The example below follows the convention for a private non-resolvable network (cannot be seen on the internet). 172 . 016 . 010 . 001 . 002 . 003 etc Set the Netmask fi eld for all projectors and computers to 255 . 255 . 255 . 000 • • • • • •
Page 4.22 105-453B January 2007 4. Using the Menus Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual Notes Do not make changes to the networking confi guration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made. The buttons of the Main menu are always visible at the bottom of the display. To go back to a previous menu option that is no longer visible, call up the menu again using the appropriate Main menu button. Confi g menu... Network confi guration... Wireless LAN Settings... IP address Netmask Encryption Menu buttons... Confi gure ethernet #1 Confi gure encryption Wireless LAN Basic networking confi guration Follow the confi guration instructions exactly as described on the previous page for Ethernet #1 . •Confi guration menu, continued
105-453B January 2007 Page 4.23 Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual 4. Using the Menus Notes Do not make changes to the networking confi guration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made. When entering the channel number, a leading zeroes must be used for single digit numbers: eg 02 If the WEP security key is to be used, then the projector must be set to the same method and number of bits as the computer or wireless access point. Confi g menu... Network confi guration... Wireless LAN... Encryption Settings... SSID Channel WEP key Mode Menu buttons... Confi gure ethernet #1 Confi gure wirelss LAN Encryption Press the ENCRYPTION button. To change the SSID, press the SSID fi eld. Use keypad to enter the (up to) 12 digits SSID. This will appear in the fi eld at the top of the keypad. Press ENTER to transfer the SSID from the keypad display to the SSID fi eld. To change the channel number, press the CHANNEL fi eld. Use keypad to enter the channel number (01 - 16, including a leading zero for single fi gure numbers). This will appear in the fi eld at the top of the keypad. Press ENTER to transfer the number from the keypad display to the Channel fi eld. To change the WEP Key, press WEP Key a number of times to cycle through the options. Choose from: Disabled 64 bits (0x1234567890) (10 hex digits) 128 bits (0x12345678901234567890123456) (26 hex digits) Pass Phrase (abcdefghijklmnopqrstuvwx) (24 characters) Press the WEP Key fi eld. Use keypad to enter the key. This will appear in the fi eld at the top of the keypad. Press ENTER to transfer the key from the keypad display to the WEP Key fi eld. To change the mode, press the MODE button to choose from: Infrastructure Access Point (usual mode for an established corporate network) Adhoc peer to peer (usual mode for a single computer and projector) • • • • •
Page 4.24 105-453B January 2007 4. Using the Menus Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual Notes The buttons of the Main menu are always visible at the bottom of the display. To go back to a previous menu option that is no longer visible, call up the menu again using the appropriate Main menu button. Touchscreen calibration should not normally be necessary except after many hours of heavy use. Confi g menu Menu buttons... Networking confi g Detailed status Touchscreen calibration Reset IP addresses Confi guration menu, continued Detailed status Press the DETAILED STATUS button. The Software release version and the total number of hours of operation are shown. Touchscreen calibration If you suspect that the LCD touchscreen has drifted out of calibration, press and hold the TOUCHSCREEN CALIBRATION button on the Confi g menu: A target appears in one corner of the screen. Press on the centre of the target and repeat as the target moves around the screen. After touching all four corners, you can wait a few seconds and carry out the calibration again, or exit by pressing the button in the centre of the screen. Reset IP addresses To reset these to their factory settings, press and hold the RESET IP ADDRESSES button. The button will turn grey - hold it until it turns yellow, then release.
105-453B January 2007 Page 4.25 Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual 4. Using the Menus Notes Software update should NOT be carried out except by, or with the supervision of, Digital Projection Service personnel. Engineering & Maintenance menu Controls Log fi les Menu buttons... Software update Engineering & Maintenance menu Press the ENGINEERING & MAINTENANCE button on the Main menu: Log fi les A single log fi le is created for each day that the projector is switched on. There will only be one fi le per day, regardless of how many times the projector has been switched on and off. The log fi les cannot be accessed from the projector touch screen. However, in the event of a problem with the projector, the log fi les can be downloaded to a remote computer via a network connection, and emailed to Digital Projection for analysis. To open a log fi le on a remote computer: Click on the log fi le name. Software update (only available via a browser, not when operating directly from the projector touch screen) This should NOT be carried out except by, or with the supervision of, Digital Projection Service personnel. •
Page 4.26 105-453B January 2007 4. Using the Menus Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual
105-453B January 2007 Page 5.1 5. Maintenance Contents Changing the lamp ............................................................................................................................. 5.2 Readind the lamp-hours meter ........................................................................................................... 5.3 Removing the lamp module ............................................................................................................... 5.4 Fitting the new lamp module .............................................................................................................. 5.4 Changing the fi lter ..............................................................................................................................5.5 Cleaning the projector and lens ...................................................................................................... 5.6
Page 5.2 105-453B January 2007 5. Maintenance Digital Projection LIGHTNING 35HD-T, 40HD-T User Manual Changing the lamp The lamp should be changed after 750 hours of use, as indicated on the lamp -hours meter. The meter is located on the front of the lamp module, and is accesible inside the lamp compartment door. To open the lamp compartment door: Give the catch half a turn anti-clockwise, to release the catch. • Notes Always allow the lamp to cool for 5 minutes before removing the lamp module. There are no user-serviceable parts inside the lamp module. The whole module should be replaced and returned to Digital Projection for re- furbishment. Do not use the lamp for more than 750 hours, as this may cause serious lamp failure, damage the lamp module and cause extra cost on replacement. Xenon lamps produce high intensity light. Do not look directly at the light coming from the lamp housing or the lens. Door catch Lamp module