Digital Projection Highlite 6000dsx User Manual

							connection should be attached to the external control equipment such as PC. The
OUT connection provides for daisy-chaining multiple projectors and operating them
with the same external equipment. To daisy-chain projectors, connect the IN termi-
nal of the second projector to the OUT connection of the first projector. A third pro-
jector would be connected to the second projector in the same manner and the pro-
cedure would be repeated until all the projectors are connected.
3 - REMOTE 1
This Mini D-Sub 15 pin terminal allows external control of the projector from either
a configured switcher or from an external control source. When the switcher is used,
connect to the REMOTE 1 terminal on the back of the switcher.
4 - REMOTE 2
Two 3.5mm stereo mini jack sockets allow direct wired connection to an individual
projector or a number of projectors. The IN connector allows direct connection of
the remote control unit. The OUT connector is used for daisy-chaining multiple pro-
jectors and operating them with the same remote control.
Plugging the cable into the projector will automatically disable the infra-red remote
receivers.
5 - INPUT 1 (RGB1) and INPUT 2 (RGB2)
Inputs with BNC terminals for connection of R, G, B, H and V outputs of external
equipment such as a switcher. If using a source with combined sync output, connect
it to the H/V terminal. The R, G, B terminals can also be used to connect component
video outputs (Y/Cb/Cr) of external equipment.
6 - INPUT 4 (Component (Y/Cb/Cr))
Inputs with RCA terminals for component video outputs (Y/Cb/Cr) of external
equipment such as DVD player.
This input accepts component signals only.
7 - INPUT 5 (VIDEO 1)
BNC composite video connection for external equipment such as a VCR or laser
disk player.
A—9
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
- 
						

							8 - INPUT 6 (VIDEO 2)
RCA composite video connection for external equipment such as a VCR or laser
disk player.
9 - INPUT 7 (S-VIDEO 1)
Two BNC connectors allow for S-Video connection for use with external equipment
such as a VCR or laser disk player that have separate Y and C video outputs.
10 - INPUT 8 (S-VIDEO 2)
Mini-DIN-4pin S-video connection for external equipment such as a VCR. This
input allows switching between S2 and S1 VIDEO input modes. See the S-Video
Mode Select section for more information.
RGB Digital Connectors & Optional SDI Board
There is a compartment above the terminal board on the front of the projector for
RGB Digital connectors and the optional SDI board. The compartment is opened by
pushing the left side of the panel.
A—10
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							11 - INPUT 9 (RGB (Digital))
DVI-D 24 pin connectors for double or triple stacking. Use the supplied DVI-D
cable to connect the OUTPUT terminal of the first projector to the second projec-
tors INPUT until all the projectors are connected.
The DVI-D cable must not exceed 5 m (16.4 feet) in length.
These connectors can also be used to accept TMDS standard digital signal output
from a digital ready computer. When used in this manner some 
graphics cards may cause flickering noise on the screen. 
The projectors support a maximum resolution of 1024x768 (4100gv and 5100gv)
or 1280x1024 (4000sx and 6000sx).
12 - INPUT 0 (SDI)
BNC SDI connection for use with equipment such as commercial type digital VTR.
Compatible with digital component signals complying with SMPTE 259M-C 
standard.
4000sx and 6000sx models are also compatible with digital component signals com-
plying with SMPTE 292M standard.
For further information on installing the optional SDI board contact your Digital
Projection Dealer.
A—11
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
-
-
OUTPUT OUTPUT
RGBDIGITAL
INPUT9 INPUT 0
SDI
11 
						

							OPTIONALLY AVAILABLE SDI BOARDS
SDI Board (all models)
This board accepts the input of non-compressed signal sources from equipment such
as commercial type digital VCR compatible with digital serial component signals of
the SMPTE 259-C standard and provides a high quality image without quantisation
noise.
BNC cable used with the SDI connector should be Belden 8281 cable, or 3C-2V
equivalent cable or better.
Included in option:-
SDI Board Shield Case
Connector Cable (Internal) Installation Manual
HDSDI Board (sx models only)
This board accepts the input of non-compressed signal sources from equipment such
as commercial type digital VCR compatible with digital serial component signals of
the SMPTE 292M standard and provides a high quality image without quantisation
noise. This board accepts the following image formats.
1920 x 1035/60/2:1 30 2:1 Interlace
1920 x 1080/60/2:1 30 2:1 Interlace
1280 x 720/60/1:1 60 Progressive
1920 x 1080/24sF 24 Progressice (Segmented Frame)
BNC cable used with the HDSDI connector should be 5C-FB equivalnt cable or
better.
Included in option:-
SDI Board Shield Case
Connector Cable (Internal) (2) Flat Cable
Set screw for Shield Case (2) Installation Manual
A—12
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
-
- 
						

							Remote Control
All the functions of your HIGHlite Displaysprojector can be controlled using the
remote control.  The remote control unit can operate either by infra red or by direct
connection to the projector via a hard wire connection.
For infra red operation the remote control requires to be powered by 2 AAA
(HP16/RO3/LR03) alkaline batteries. The battery compartment is located on the
back of the remote control. To remove the compartment cover press and open as
shown below.
Insert the first battery into the compartment according to the (+) and (-) indications
inside the case and it to the back of the compartment. Insert the second battery by
pivoting it against the first and pushing down into place. When the batteries are
securely in place, replace the battery compartment cover.
When using infra red operation the remote control has an effective range of about
7m (23 feet) and at an angle of 30° above, below, to the left and to the right of the
remote control sensors located at the front and the rear of the projector.
The remote control should not be exposed to heat, steam, water or any other liquid.
If the remote control gets wet, wipe it dry immediately. 
When remote control buttons are pressed and held down the main unit function
keys may not operate.
You cannot operate the projector using the remote control if the remote ID is not
set to [00] or the remote ID is not the same as the projector ID. 
Very bright flourescent lighting or Infra Red translation systems may saturate the
projectors’ Infra Red receiver rendering the remote control inoperative.
A—13
0verview
OVERVIEW
LBV00072; Revision A - 25/09/2001
-
-
- 
						

							A—14
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							Installation Guidelines...................................................... B—1
Screen Requirements................................................... B
—1
Positioning the Projector  .............................................. B
—4
Installation ....................................................................... B—7
Attaching the Power Cable Stopper ........................... B—7
Lens Installation .......................................................... B—8
Setting Up the Projector ................................................. B—11
Reflecting the Displayed Image ............................... B—12
Shutter Mechanism ................................................... B—12
Turning Off the Projector ........................................... B—12
Startup Screen (Language Select) ................................. B—13
Connecting Signal Sources ............................................ B—15
System Installation
Section B: System Installation
INSTALLATION
LBV00072; Revision A - 25/09/2001 
						

							System Installation
INSTALLATION
LBV00072; Revision A - 25/09/2001 
						

							This installation section explains how to install the projector for optimum results.
To do this, it is necessary to determine the following:
1. The type of screen and whether front or rear projection is to be used.
2. The projector location and therefore the type of lens to be used.
3. The method of mounting for the projector.
4. The type of input source to be used with the projector.
Screen Requirements
As virtually all commercially available screens will give a pleasing image you
should choose according to your individual requirements. However, to achieve 
optimum results we recommend a low gain (1.2 - 1.3), non-perforated screen for
front projection, this will keep hot spotting and light loss to a minimum whilst 
providing wide viewing angles. 
Regardless of the type of screen used, it is important that your screen is of sufficient
height to display the images at the aspect ratios intended to be used. Use the 
following tables to check that you are able to display the full image on your screen.
If you have insufficient height, you will have to reduce the overall image size in
order to display the full image on your screen.
B—1
System Installation
Installation Guidelines
INSTALLATION
LBV00072; Revision A - 25/09/2001
Screen Width
(metres)
2.40
3.00
3.60
4.20
4.80
6.00
10.004 x 3
1.80
2.25
2.70
3.15
3.60
4.50
7.505 x 4
1.92
2.40
2.88
3.36
3.84
4.80
8.008 x 5
1.5
1.87
2.25
2.62
3.00
3.75
6.2514 x 9
1.54
1.93
2.31
2.70
3.09
3.86
6.4316 x 9
1.35
1.69
2.02
2.36
2.70
3.38
5.63Screen Height (metres) Needed to Display Full Image with Aspect Ratio: 
						

							For optimum viewing, the screen should be a flat surface perpendicular to the floor.
The bottom of the screen should be 1.2m (4 feet) above the floor and the front row
of the audience should not have to look up more than 30° to see the top of the
screen (see opposite).
The distance between the front row of the audience and the screen should be at least
twice the screen height and the distance between the back row and the screen should
be a maximum of 8 times the screen height. The screen viewing area should be
within a 60° range from the face of the screen.
If you intend to use a rear projection screen you must ensure you have sufficient
distance behind the screen for the projector to be correctly located Rear projection
has the advantage that the projector cannot be seen and higher ambient light levels
can be tolerated. Although the image can be flipped to rear projection and displayed
without the need for extra mirrors or equipment, it makes the installation more 
complicated and advice should be sought from your local dealer before attempting
an installation in this way.
B—2
System Installation
INSTALLATION
LBV00072; Revision A - 25/09/2001
Screen Width
(feet)
8 0
10 0
12 0
14 0
16 0
20 0
30 04 x 3
6 0
7 6
9 0
10 6
12 0
15 0
22 65 x 4
6 5
8 0
9 7
11 2
12 10
16 0
24 08 x 5
5 0
6 3
7 6
8 9
10 0
12 6
18 914 x 9
5 2
6 5
7 9
9 0
10 8
12 10
19 416 x 9
4 6
5 8
6 9
7 11
9 0
11 4
16 11Screen Height (feet/inches) Needed to Display Full Image with Aspect Ratio: